• Relay output warning for power failure and port break alarm
• Broadcast storm protection
• Transparent transmission of VLAN tagged packets
• -40 to 75°C operating temperature range (T models)

• 20 KA lightning surge protection
• Two passive 10 / 100 / 1000 Ethernet ports
• One ground position
• Flexibly designed for various Ethernet devices including PoE

  To prevent Ethernet devices from possible damage caused by surge voltages as a result of lightning strikes, PLANET has released a new Ethernet Lightning Arrest Box especially made in the current Ethernet environment.   The ELA-100 Ethernet Lightning Arrest Box provides two passive 10 / 100 / 1000Base-T interfaces for connection of two Ethernet devices and one ground position for earth. The ELA-100 Ethernet Lightning Arrest Box is the ideal solution to preventing damages to Ethernet devices from surge voltages caused by lightning strikes.

• 8-Port 10/100/1000Base-T RJ-45 copper • 2 100/1000Base-X mini-GBIC/SFP slots, SFP type auto detection   Industrial Case / Installation • IP30 aluminum case protection • DIN-rail and wall mount design • Redundant Power Design 　- 12 to 48V DC, redundant power with polarity reverse protect function 　- AC 24V power adapter acceptable • Supports EFT protection 6000 VDC for power line • Supports 6000 VDC Ethernet ESD protection • -40 to 75 degrees C operating temperature   Layer 2 Features • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth • Storm Control support 　- Multicast / Unknown-Unicast • Supports VLAN 　- IEEE 802.1Q Tagged VLAN 　- Up to 255 VLANs groups, out of 4095 VLAN IDs 　- Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad) 　- Private VLAN Edge (PVE) 　- Protocol-based VLAN 　- MAC-based VLAN 　- Voice VLAN • Supports Spanning Tree Protocol 　- STP, IEEE 802.1D Spanning Tree Protocol 　- RSTP, IEEE 802.1w Rapid Spanning Tree Protocol 　- MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN 　- BPDU Guard • Supports Link Aggregation 　- 802.3ad Link Aggregation Control Protocol (LACP) 　- Cisco ether-channel (Static Trunk) 　- Maximum 5 trunk groups, up to 10 ports per trunk group 　- Up to 20Gbps bandwidth (duplex mode) • Provides Port Mirror (many-to-1) • Port Mirroring of the incoming or outgoing traffic on a particular port • Supports E.R.P.S. (Ethernet Ring Protection Switching)   Quality of Service • Ingress Shaper and Egress Rate Limit per port bandwidth control • 8 priority queues on all switch ports • Traffic classification 　- IEEE 802.1p CoS 　- IP TOS / DSCP / IP Precedence 　- IP TCP/UDP port number 　- Typical network application • Strict priority and Weighted Round Robin (WRR) CoS policies • Supports QoS and In/Out bandwidth control on each port • Traffic-policing policies on the switch port • DSCP remarking   Multicast • Supports IGMP Snooping v1, v2 and v3 • Supports MLD Snooping v1 and v2 • Querier mode support • IGMP Snooping port filtering • MLD Snooping port filtering • MVR (Multicast VLAN Registration)   Security • IEEE 802.1x Port-based / MAC-based network access authentication • Built-in RADIUS client to co-operate with the RADIUS servers • TACACS+ login users access authentication • RADIUS / TACACS+ users access authentication • IP-based Access Control List (ACL) • MAC-based Access Control List • Source MAC / IP address binding • DHCP Snooping to filter untrusted DHCP messages • Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding • IP Source Guard prevents IP spoofing attacks • Auto DoS rule to defend DoS attack • IP address access management to prevent unauthorized intruder   Management • Switch Management Interfaces 　-Web switch management 　-Remote Telnet management 　-SNMP v1, v2c, and v3 switch management 　-SSH / SSL secure access • Four RMON groups (history, statistics, alarms, and events) • IPv6 IP Address / NTP / DNS management • Built-in Trivial File Transfer Protocol (TFTP) client • BOOTP and DHCP for IP address assignment • Firmware upload/download via HTTP / TFTP • DHCP Relay • DHCP Option 82 • User Privilege levels control • NTP (Network Time Protocol) • System Log • Link Layer Discovery Protocol (LLDP) Protocol • Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues • Reset button for system reboot or reset to factory default • PLANET Smart Discovery Utility for deploy management   PLANET IGS-10020MT is an Industrial 10-Port Full Gigabit Managed Ethernet Switch specially designed to build a full Gigabit backbone to transmit reliable but high speed data in heavy industrial demanding environments and forward data to remote network through fiber optic. It provides 8-port 10/100/1000Base-T copper and 2 extra 100/1000Base-X SFP fiber optic interfaces delivered in an IP30 rugged strong caiise with redundant power system. Besides support for 20Gbps switch fabric to handle extremely large amounts of video, voice and important data in a secure topology, the IGS-10020MT provides user-friendly but advanced IPv6 / IPv4 management interfaces and abundant L2 / L4 switching functions. It is the best investment for industrial business expanding or upgrading its network infrastructure    IPv6 / IPv4 Full-functioned Secure Switch for Building Automation Networking The IGS-10020MT is the ideal solution to fulfilling the demand of IPv6 management Gigabit Ethernet Switch, especially in the Industrial hardened environment. It supports both IPv4 and IPv6 management functions and can work with original network structure. It provides advanced Layer 2 to Layer 4 data switching and redundancy, Quality of Service traffic control, network access control and authentication, and Secure Management features to protect customer’s industrial and building automation network connectivity with reliable switching recovery capability that is suitable for implementing fault tolerant and mesh network architectures.    Redundant Ring, Fast Recovery for Surveillance System The IGS-10020MT supports redundant ring technology and features strong rapid self-recovery capability to prevent interruptions and external intrusions. It incorporates advanced ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) technology, Spanning Tree Protocol (802.1s MSTP), and redundant power input system into customer’s industrial automation network to enhance system reliability and uptime in harsh factory environments. In certain simple Ring network, the recovery time of data link can be as fast as 20 ms.    Environmentally Hardened Design With IP30 aluminum industrial case protection, the IGS-10020MT provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. It also possesses an integrated power supply source with wide range of voltages (12 to 48V DC or 24V AC) for worldwide high availability applications requiring dual or backup power inputs. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-10020MT can be placed in almost any difficult environment.    Flexible and Extendable Solution The 2 mini-GBIC slots built in the IGS-10020MT support dual-speed, 100Base-FX and 1000Base-SX/LX SFP (Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can flexibly choose the suitable SFP transceiver according to the transmission distance or the transmission speed required to extend the network efficiently. The IGS-10020MT supports SFP-DDM(Digital Diagnostic Monitor) function that can easily monitor real-time parameters of the SFP for network administrator, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.

• 5-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function

  Layer 2 Features

• Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX Ethernet standard
• Supports auto-negotiation and 10/100Mbps half/full duplex mode
• High performance Store and Forward architecture; runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (switching fabric): 1Gbps
• Integrated address look-up engine, supporting 1K absolute MAC addresses
• Automatic address learning and address aging

  Industrial Case & Installation

• IP30-rated metal case
• DIN rail and wall-mount design
• 12 to 48V DC, redundant power with polarity reverse protection function and connective removable terminal block for master and slave power, 24V AC power support
• Lower Power Consumption device in full load operation mode
• Supports EFT protection for 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 degrees C operating temperature
• Free fall, shock-proof and vibration-proof for industries

  Slim Type with More Practicability and Convenience The IGS-501T advanced, slim-type, industrial, hardened Gigabit Ethernet Switch with IP30 metal case consists of 5 10/100/1000Mbps auto negotiation ports and thus, it operates reliably in heavy industrial demanding environments. Its compact IP30 standard metal case features either DIN rail or wall mount for the efficient use of cabinet space.   Stable Performance under Difficult Environments The IGS-501T provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C coupled with hazardous location certification (Class 1 Division 2), the IGS-501T can be placed in almost any difficult environment. The IGS-501T also possesses an integrated power supply source with a wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust Switch Performance The IGS-501T offers high performance switch architecture. With the 5 10/100/1000Mbps Gigabit Ethernet ports providing non-blocking switch fabric and wire-speed throughput as high as 10Gbps and the 2K MAC address table, the IGS-501T can perform wire-speed packets transfer without risk of packet loss.   The flow control function enables the IGS-501T to provide fast and reliable data transfer. The Gigabit port with 9K Jumbo frame supported can handle extremely large amounts of data transmission in industrial topology that forward data to central control room.   Plug and Play All of the RJ-45 copper interfaces in the IGS-501T support 10/100/1000Mbps auto negotiation for optimal speed detection through RJ-45 Category 6, 5 or 5e cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.

Physical Port

• 4 10/100/1000BASE-T Gigabit Ethernet RJ45 ports
• 2 100/1000BASE-X mini-GBIC/SFP slots for SFP type auto detection
• One RJ45 console interface for basic management and setup

  Industrial Case and Installation

• IP30 metal case
• DIN rail and wall-mount design
• 12~48V DC, redundant power with polarity reverse protect function
• 24V AC power input acceptable
• Supports 5000V DC Ethernet ESD protection
• -40 to 75 degrees C operating temperature

  Layer 2 Features

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support

- Broadcast/Multicast/Unicast

• Supports VLAN

- IEEE 802.1Q tagged VLAN - Up to 255 VLANs groups, out of 4094 VLAN IDs- Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad) - Private VLAN Edge (PVE) - Protocol-based VLAN- MAC-based VLAN- Voice VLAN

• Supports Spanning Tree Protocol

- IEEE 802.1D Spanning Tree Protocol (STP) - IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) - IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN - BPDU Guard

• Supports Link Aggregation

- 802.3ad Link Aggregation Control Protocol (LACP) - Cisco ether-channel (static trunk) - Maximum 4 trunk groups with 4 ports per trunk group - Up to 8Gbps bandwidth (duplex mode) - Provides port mirror (1-to-1)

• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loopsv
• Supports ERPS (Ethernet Ring Protection Switching)

  Layer 3 IP Routing Features

• Supports maximum 32 static routes and route summarization

  Quality of Service

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification

- IEEE 802.1p CoS - IP TOS/DSCP/IP precedence - IP TCP/UDP port number - Typical network application

• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing policies on the switch port
• DSCP remarking

  Multicast

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)

  Security

• IEEE 802.1X Port-based/MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers
• TACACS+ login users access authentication
• RADIUS/TACACS+ users access authentication
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Source MAC/IP address binding
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management

• Switch Management Interfaces

- Console/Telnet Command Line Interface - Web switch management - SNMP v1 and v2c switch management - SSH/SSL and SNMP v3 secure access

• Four RMON groups (history, statistics, alarms, and events)
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• Firmware upload/download via HTTP/TFTP
• DHCP Relay
• DHCP Option 82
• User Privilege levels control
• Network Time Protocol (NTP)
• Link Layer Discovery Protocol (LLDP)
• SFP-DDM (Digital Diagnostic Monitor)
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• Reset button for system reboot or reset to factory default
• PLANET Smart Discovery Utility for deployment management

        An Ideal Fiber Switch with Limited Space PLANET IGS-5225-4T2S is the smallest, fully-managed Gigabit fiber switch in the industrial networking industry that features 4 10/100/1000Mbps copper ports, 2 100/1000X SFP ports and redundant power system in an IP30 rugged but compact-sized case, can be installed in any difficult environment without space limitation. Within such slim enclosure, it provides user-friendly yet advanced IPv6/IPv4 management interfaces, abundant L2/L4 switching functions and Layer 3 static routing capability. The IGS-5225-4T2S can operate stably under the temperature range from -40 to 75 degrees C and allows either DIN rail or wall mounting for efficient use of cabinet space. With 2 dual-speed SFP fiber slots, it can be flexibly applied to extend the connection distance.   Redundant Ring, Fast Recovery for Critical Network Applications The IGS-5225-4T2S supports redundant ring technology and features strong, rapid self-recovery capability to prevent interruptions and external intrusions. It incorporates advanced ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) technology, Spanning Tree Protocol (802.1s MSTP), and redundant power input system into customer’s industrial automation network to enhance system reliability and uptime in harsh factory environments. In a certain simple Ring network, the recovery time of data link can be as fast as 20ms.   SMTP/SNMP Trap Event Alert The IGS-5225-4T2S provides event alert function to help to diagnose the abnormal device owing to whether or not there is a break of the network connection, or the rebooting response.   Effective Alarm Alert for Better Protection The IGS-5225 series supports a Fault Alarm feature which can alert the users when there is something wrong with the switches. With this ideal feature, the users would not have to waste time finding where the problem is. It will help to save time and human resource.   Layer 3 IPv4 and IPv6 Software VLAN Routing for Secure and Flexible Management To help customers stay on top of their businesses, the IGS-5225 series not only provides ultra high transmission performance and excellent Layer 2 technologies, but also IPv4/IPv6 software VLAN routing feature which allows to crossover different VLANs and different IP addresses for the purpose of having a highly-secure, flexible management and simpler networking application.   Robust Layer 2 Features The IGS-5225 series can be programmed for advanced switch management functions such as dynamic port link aggregation, Q-in-Q VLAN, private VLAN, Rapid Spanning Tree Protocol, Layer 2 to Layer 4 QoS, bandwidth control and IGMP snooping. The IGS-5225 series provides 802.1Q tagged VLAN, and the VLAN groups allowed will be maximally up to 255. Via aggregation of supporting ports, the IGS-5225-4T2S allows the operation of a high-speed trunk combining multiple ports. It enables a maximum of up to 10 trunk groups with 8 ports per trunk group, and supports fail-over as well.   Efficient Management For efficient management, the IGS-5225 Managed Ethernet Switch series is equipped with console, Web and SNMP management interfaces. With the built-in Web-based management interface, the IGS-5225 series offers an easy-to-use, platform-independent management and configuration facility. For text-based management, the IGS-5225 series can be accessed via Telnet and the console port. Moreover, it also offers secure remote management via any standard-based management software by supporting SNMPv3 connection which encrypts the packet content at each session.   Powerful Security The IGS-5225 series offers comprehensive Layer 2 to Layer 4 Access Control List (ACL) for enforcing security to the edge. It can be used to restrict network access by denying packets based on source and destination IP address, TCP/UDP ports or defined typical network applications. Its protection mechanism also comprises 802.1X Port-based and MAC-based user and device authentication. With the private VLAN function, communication between edge ports can be prevented to ensure user privacy. The network administrators can now construct highly-secure corporate networks with considerably less time and effort than before.   Flexibility and Extension Solution The additional two mini-GBIC slots built in the IGS-5225-4T2S support dual speed, 100BASE-FX and 1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can flexibly choose the suitable SFP transceiver according to not only the transmission distance but also the transmission speed required. The distance can be extended from 550 meters (multi-mode fiber) to 10/50/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.   Intelligent SFP Diagnosis Mechanism The IGS-5225 series supports SFP-DDM (Digital Diagnostic Monitor) function that greatly helps network administrator to easily monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.   1588 Time Protocol for Industrial Computing Networks The IGS-5225 series is ideal for telecom and Carrier Ethernet applications, supporting MEF service delivery and timing over packet solutions for IEEE 1588 and synchronous Ethernet.   Modbus TCP provides Flexible Network Connectivity for Factory Automation With the supported Modbus TCP/IP protocol, the IGS-5225 series can easily integrate with SCADA systems, HMI systems and other data acquisition systems in factory floors. It enable administrators to remotely monitor the industrial Ethernet switch’s operating information, port information and communication status, thus easily achieving enhanced monitoring and maintenance of the entire factory.

• 5x 10/100/1000BASE-T Gigabit Ethernet RJ45 copper ports
• 1x SFP slot, supporting 1000BASE-X and 100BASE-FX transceiver in dual modes 

Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus, end-span PSE
• Backward compatible with IEEE 802.3af Power over Ethernet
• Up to 4 ports of IEEE 802.3af/at devices powered
• Up to 120-watt PoE budget
• Supports PoE power up to 36 watts for each PoE port
• Each port supports 54V DC power to PoE powered device
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m 

Layer 2 Switching:

• Features Store-and-Forward mode with wire-speed filtering and forwarding rates
• IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
• 4K MAC address table size
• 10K jumbo frame
• IEEE 802.1Q VLAN transparency
• Automatic address learning and address aging
• Supports CSMA/CD protocol 

Industrial Case and Installation:

• IP40 metal case
• DIN-rail, wall-mount or side wall-mount design
• 12~56V DC redundant power with reverse polarity protection
• Fault alarm for power input failed
• Supports 6KV DC Ethernet ESD protection
• -40 to 75 degrees C operating temperature 
• 4 real-time PoE power usage indicators

Cost-effective Full PoE+ Power Solution Ideal for Hardened Environment:
Featuring Plug and Play designed to be installed in heavy industrial demanding environments, the IGS-614HPT is a PLANET Industrial-grade, DIN-rail type Unmanaged Gigabit Ethernet PoE+ Switch with four 10/100/1000BASE-T ports featuring IEEE 802.3at PoE+, one extra 10/100/1000BASE-T RJ45 copper and one 100/1000BASE-X fiber optic interface for uplink connection. The IGS-614HPT is designed with redundant power system and is able to operate reliably, stably and quietly in any hardened environment without affecting its performance. It comes with a total power budget of up to 120 watts for different kinds of PoE applications and operating temperature ranging from -40 to 75 degrees C in a rugged IP40 metal housing. Convenient and Reliable Power System:
To facilitate the 802.3at PoE+ usage with commonly used 12~48V DC power input for transportation and industrial-level applications, the IGS-614HPT adopts 12~48V DC to 54V power boost technology to solve power source issue but does not require special power supplies. The IGS-614HPT provides an integrated power solution with a wide range of voltages (12~48V DC) for worldwide operability. It also provides dual-redundant, reversible polarity 12~56V DC power supply inputs for high availability applications. Fiber Optic Link Capability for Flexible Distance Extension:
The additional mini-GBIC slot built in the IGS-614HPT supports SFP auto-detection and dual speed as it features 100BASE-FX and 1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can flexibly choose the suitable SFP transceiver according to the transmission distance or the transmission speed required to extend the network efficiently. The distance can be extended from 550 meters to 2 kilometers (multi-mode fiber) and 10/20/30/40/50/60/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications to uplink to backbone switch and monitoring center in long distance. Environmentally Hardened Design:
With the IP40 metal industrial case, the IGS-614HPT provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb-side traffic control cabinets without air conditioning. It features a ventilated construction in which a cooling fan is not necessary, thereby making its operation noiseless. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-614HPT can be placed in almost any difficult environment. Robust Protection:
The IGS-614HPT provides contact discharge of ±6KV DC and air discharge of ±8KV DC for Ethernet ESD protection. It also supports ±6KV surge immunity to improve product stability and protects users’ networks from devastating ESD attacks, making sure the flow of operation does not fluctuate. Intelligent LED Indicator for Real-time PoE Usage:
The IGS-614HPT helps users to monitor current status of PoE power usage easily and efficiently by its advanced LED indication. Called “PoE Power Usage”, the front panel of the Industrial Gigabit PoE+ Switch has four orange LEDs indicating 30W, 60W, 90W and 120W of PoE power usage. Flexible and Easy Installation with Limited Space:
The compact sized IGS-614HPT is specially designed to be installed in a narrow environment, such as wall enclosure. It can be installed by fixed wall mounting or DIN rail, thereby making its usability more flexibly and easily in any space-limited location.

• 4-port 10/100/1000Base-T RJ-45 with IEEE 802.3af / 802.3at PoE Injector
• 2-port SFP slot interface, SFP supports 1000Base-X and 100Base-FX transceiver via DIP switch configured

Power over Ethernet

• Complies with IEEE 802.3af / IEEE 802.3at Power over Ethernet Plus End-Span PSE
• Up to 4 IEEE 802.3af / 802.3at devices powered

 

• Supports PoE Power up to 30.8 watts for each PoE port
• Provides DC 52V power over RJ-45 Ethernet cable to PD with Ethernet port
• Auto-detects EEE 802.3af/at equipment and protects devices from being damaged by incorrect installation
• Remote power feeding up to 100m

Layer 2 Features

• Supports Auto-Negotiation and 10/100Mbps half / full duplex and 1000Mbps full duplex mode
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x PAUSE frame flow control (full-duplex)
• Automatic address learning and address aging

Industrial Case / Installation

• IP30 aluminum metal case protection
• Dual SFP Ports Auto Link Redundant Mode Support
• DIN Rail and Wall Mount Design
• 48V DC redundant power with polarity reverse protect function and removable terminal block for master and slave power
• Supports EFT protection 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 degrees C operating temperature

  Long Distance High Power PoE and Gigabit Data Extension Solution The PLANET IGS-624HPT is an Industrial Gigabit 802.3at PoE+ Switch providing non-blocking wire-speed performance and great flexibility for Gigabit Ethernet extension in harsh industrial environment. It provides 4-port 10/100/1000Base-T copper with 802.3af/at PoE injector and 2 extra 100/1000Base-X SFP fiber optic interfaces delivered in an IP30 rugged strong case with redundant power system. The IGS-624HPT is well suited for applications in deploying surveillance system, and securing control and wireless service in climatically demanding environments with wide temperature range from -40 to 75 degrees C.   High Power PoE for Security and Public Service Applications To fulfill the demand of High Power PoE for network applications, the IGS-624HPT provides 4 10/100/1000Mbps ports featuring both IEEE 802.3af and IEEE 802.3at Power over Ethernet Plus (PoE+) that combine up to 30-watt of power output and data per port over one Cat.5E / 6 Ethernet cable. With totally 120-watt PoE output capability on the whole system, the IGS-624HPT is designed specifically to satisfy the growing demand of higher power consuming network PD (powered devices) such as PTZ (Pan, Tilt & Zoom) / Speed Dome network cameras, multi-channel (802.11a / b / g / n) outdoor wireless LAN access points and other PoE network devices by providing double PoE power, rather than the current conventional 802.3af PoE.    Intelligent LED Indicator for Real-time PoE Usage The IGS-624HPT helps users to monitor current status of PoE power usage easily and efficiently by its advanced LED indication. Called “PoE Power Usage”, the front panel of the Industrial Gigabit PoE+ Switch has four orange LEDs indicating 30W, 60W, 90W and 120W of PoE power usage.    Convenient and Reliable Power System To facilitate the 802.3at High Power PoE usage with the commonly used 48V DC power input in transportation and industrial-level applications, the IGS-624HPT adopts 48V DC to 52V DC power boost technology to solve power source issue which is not required for special power supplies to achieve the level of High Power PoE+ output. To enhance the operation reliability and flexibility, the IGS-624HPT is equipped with two DC power input connectors for redundant power supply installation.      High Power Budget for PoE Extension With 30-watt PoE output capability, the IGS-624HPT can extend much longer distance by using PLANET PoE Extender for powering up the IEEE 802.3af PoE PD devices which can be installed over more than 100 meters away. By daisy-chaining multiple PLANET PoE Extenders, it offers the great flexibility of doubling, tripling or quadrupling the distance of PoE network.    Environmentally Hardened Design The IGS-624HPT is equipped with the rugged IP30 metal case for easy deployment in heavy Industrial demanding environments. With IP30 industrial case protection, the IGS-624HPT provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-624HPT can be placed in almost any difficult environment. The IGS-624HPT also allows either DIN rail or wall mounting for efficient use of cabinet space.   Fiber-Optical Link Capability Extend the Range of Network Deployment The two SFP slots are compatible with 100Base-FX or 1000Base-SX / LX / WDM through SFP (Small Form Factor Pluggable) fiber-optic transceivers. The fiber optical uplink capability guarantees the throughput to all nodes hooked into the network and the Gigabit Ethernet distance can be extended from 550 meters (Multi-Mode fiber cable) up to 10/20/30/40/50/70/120 kilometers (Single-Mode fiber or WDM fiber).      Adjustable 6-Port Switch Mode or 4 + 2 Fiber Redundant Mode Via the built-in DIP switch, the IGS-624HPT can be configured as 6-port Ethernet switch or 4+2 fiber redundant mode. With the 6-port switch mode, the IGS-624HPT can operate in Store-and-Forward mechanism with high performance; on the other hand, when in the 4+2 fiber redundant mode, it provides rapid fiber redundancy of link for highly critical Ethernet applications. The redundant mode also supports auto-recovering function. If the destination port of a packet is link down, it will forward the packet to the other port of the backup pair.

•  8-Port 10/100/1000BASE-T RJ45 copper

  Industrial Case/Installation

• IP30 metal case protection
• DIN-rail and wall mount design
• Redundant power design

- 12 to 48V DC, redundant power with polarity reverse protect function - AC 24V power adapter acceptable

• Supports EFT 6000VDC protection for power line
• Supports 6000VDC Ethernet ESD protection
• -40 to 75 degrees C operating temperature

  Layer 2 Features

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance Store and Forward architecture, broadcast storm control, runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Supports VLAN

- IEEE 802.1Q tagged VLAN - Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad) - Protocol VLAN - Voice VLAN - Private VLAN - Management VLAN - GVRP

• Supports Spanning Tree Protocol

- STP (Spanning Tree Protocol) - RSTP (Rapid Spanning Tree Protocol) - MSTP (Multiple Spanning Tree Protocol) - STP BPDU Guard, BPDU filtering and BPDU forwarding

• Supports Link Aggregation

- IEEE 802.3ad Link Aggregation Control Protocol (LACP) - Cisco ether-channel (static trunk)

• Provides port mirror (many-to-1)
• Loop protection to avoid broadcast loops

  Quality of Service

• Ingress and egress rate limit per port bandwidth control
• Storm control support

- Broadcast/Unknown unicast/Unknown multicast

• Traffic classification

- IEEE 802.1p CoS - TOS/DSCP/IP precedence of IPv4/IPv6 packets

• Strict priority and Weighted Round Robin (WRR) CoS policies

  Multicast

• Supports IPv4 IGMP snooping v2 and v3
• Supports IPv6 MLD snooping v1, v2
• IGMP querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering

  Security

• Authentication

- IEEE 802.1X port-based network access authentication - Built-in RADIUS client to co-operate with the RADIUS servers - RADIUS/TACACS+ login user access authentication

• Access control list

- IPv4/IPv6 IP-based ACL - MAC-based ACL

• MAC security

- Static MAC - MAC filtering

• Port security for source MAC address entries filtering
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP source guard prevents IP spoofing attacks
• DoS attack prevention
• SSH/SSL

  Management

• IPv4 and IPv6 dual stack management
• Switch management interface

- Web switch management - Telnet command line interface - SNMP v1, v2c and v3 - SSH and SSL secure access

• User privilege levels control
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System maintenance

- Firmware upload/download via HTTP/TFTP - Configuration upload/download through web interface - Dual images - Hardware reset button for system reboot or reset to factory default

• SNTP Network Time Protocol
• Cable diagnostics
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• SNMP trap for interface link up and link down notification
• Event message logging to remote Syslog server
• Four RMON groups (history, statistics, alarms and events)
• PLANET smart discovery utility

   Perfect, Slim-type Managed Switch with More Practicability and Convenience PLANET IGS-801M is an Industrial 8-Port Full Gigabit Managed Ethernet Switch specially designed to transmit reliable but high-speed data in heavy industrial demanding environments. It provides 8-Port 10/100/1000BASE-T copper interfaces delivered in an IP30 rugged strong case with redundant power system. Besides support for 16Gbps switch fabric to handle extremely large amounts of video, voice and important data in a secure topology, the IGS-801M provides user-friendly but advanced IPv6/IPv4 management interfaces and abundant L2/L4 switching functions. It is the best investment for industrial business expanding or upgrading its network infrastructure.    Environmentally Hardened Design With IP30 industrial case protection, the IGS-801M provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb-side traffic control cabinets. It also possesses an integrated power supply source with wide range of voltages (12 to 48V DC or 24V AC) for worldwide high availability applications requiring dual or backup power inputs. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-801M can be placed in almost any difficult environment.   Robust Layer 2 Features The IGS-801M can be programmed for advanced switch management functions such as dynamic port link aggregation, 802.1Q VLAN and Q-in-Q VLAN, Multiple Spanning Tree Protocol (MSTP), loop and BPDU guard, IGMP snooping, and MLD snooping. Via the link aggregation, the IGS-801M allows the operation of a high-speed trunk to combine with multiple ports, and supports fail-over as well. Also, the Link Layer Discovery Protocol (LLDP) is the Layer 2 protocol included to help discover basic information about neighboring devices on the local broadcast domain.    Efficient Traffic Control The IGS-801M is loaded with robust QoS features and powerful traffic management to enhance services to business-class data, voice and video solutions. The functionality includes broadcast/multicast storm control, per port bandwidth control, IP DSCP QoS priority and remarking. It guarantees the best performance for VoIP and video stream transmission, and empowers the enterprises to take full advantage of the limited network resources.   Powerful Security PLANET IGS-801M offers comprehensive IPv4/IPv6 Layer 2 to Layer 4 Access Control List (ACL) for enforcing security to the edge. It can be used to restrict network access by denying packets based on source and destination IP address, TCP/UDP ports or defined typical network applications. Its protection mechanism also comprises 802.1X port-based user and device authentication, which can be deployed with RADIUS to ensure the port level security and block illegal users. With the protected port function, communication between edge ports can be prevented to guarantee user privacy. Furthermore, port security function allows to limit the number of network devices on a given port.   Advanced Network Security The IGS-801M also provides DHCP snooping, IP source guard and dynamic ARP inspection functions to prevent IP snooping from attack and discarded ARP packets with invalid MAC address. The network administrators can now construct highly-secure corporate networks with considerably less time and effort than before.   Friendly and Secure Management For efficient management, the IGS-801M is equipped with web, Telnet and SNMP management interfaces. With the built-in web-based management interface, the IGS-801M offers an easy-to-use, platform-independent management and configuration facility. By supporting the standard SNMP, the switch can be managed via any standard management software. For text-based management, the switch can be accessed via Telnet. Moreover, the IGS-801M offers secure remote management by supporting SSH, SSL and SNMP v3 connections which encrypt the packet content at each session.

• 5-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function

  Layer 2 Features

• Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX Ethernet standard
• Supports auto-negotiation and 10/100Mbps half/full duplex mode
• High performance Store and Forward architecture; runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (switching fabric): 1Gbps
• Integrated address look-up engine, supporting 1K absolute MAC addresses
• Automatic address learning and address aging

  Industrial Case & Installation

• IP30-rated metal case
• DIN rail and wall-mount design
• 12 to 48V DC, redundant power with polarity reverse protection function and connective removable terminal block for master and slave power, 24V AC power support
• Lower Power Consumption device in full load operation mode
• Supports EFT protection for 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 degrees C operating temperature
• Free fall, shock-proof and vibration-proof for industries

  Slim type with more practicability and convenience After PLANET ISW/IFT Fast Ethernet Switch/Converter series become popular, PLANET has released the advanced industrial hardened Fast Ethernet Switch series with slim type, IP30 metal case. The compact, IP30 standard metal case allows either DIN rail or wall mounting to have the efficient use of cabinet space. The ISW-501T, one of the new models, is equipped with five 10/100Mbps auto negotiation ports and operates reliably in heavy industrial demanding environments.   Stable operating performance under difficult environments The ISW-501T provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C, the ISW-501T can be placed in almost any difficult environment. The ISW-501T also possesses an integrated power supply source with wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust switch performance The ISW-501T offers high performance switch architecture. With the five 10/100Mbps Fast Ethernet ports providing non-blocking switch fabric and wire-speed throughput as high as 1Gbps and the 2K MAC Address table, the ISW-501T can perform wire-speed packets transfer without risk of packet loss. The flow control function enables the ISW-501T to provide fast and reliable data transfer.   All of the RJ-45 copper interfaces in the ISW-501T support 10/100Mbps auto negotiation for optimal speed detection through RJ-45 Category 3, 4 or 5 cables. The standard auto-MDI / MDI-X support can detect the type of connection to any Ethernet device without requiring special-through or crossover cables.  

• 5-Port 10/100Mbps RJ-45 with aouto MDI/MDI-X function
• 4-Port support 48V DC power to PoE Powered Device (Port-1 to Port-4)

  IEEE 802.3af PoE

• Complies with IEEE 802.3af Power over Ethernet End-Span PSE
• Up to 4 IEEE 802.3af devices powered
• Supports PoE Power up to 15.4 Watts for each PoE port
• Auto detect powered device (PD)
• Circuit protection prevent power interference between ports
• Remote power feeding up to 100m

  Layer 2 Features  

• Supports Auto-Negotiation and 10/100Mbps Half / Full Duplex and Auto MDI/MDI-X
• High performance Store and Forward architecture, runt / CRC filtering eliminates 　　 
• erroneous packets to optimize the network bandwidth
• Prevents packet loss with back pressure (Half-Duplex) and IEEE 802.3x PAUSE frame
• flow control (Full-Duplex)
• Automatic address learning and address aging
• Integrated address look-up engine, support 2K absolute MAC addresses
• CSMA / CD Protocol
• Industrial Case / Installation

IP-30 Aluminum metal case protection

• DIN Rail and Wall Mount Design
• Redundant Power Design
• 24V or 48V DC, redundant power with polarity reverse protect function
• Supports EFT protection 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 Degree C operation temperature 

  The PLANET ISW-504PT PoE Industrial Ethernet Switch is designed to transmit power and data over single Ethernet cable to remote PoE capable devices and operates reliably in heavy industrial demanding environments. The ISW-504PT provides 5 10/100Mbps copper ports with 4-Port IEEE 802.3af Power over Ethernet inject interfaces delivered in an IP-30 rugged strong case. Supporting up to 15.4Watts power per port for any remote IEEE 802.3af powered device (PD) such as PoE IP cameras and PoE wireless LAN access point, the ISW-504PT is an ideal solution to deploy surveillance system and wireless service in climatically demanding wide temperature range(-40 to 75 Degree C)environments.   IEEE 802.3af Power over Ethernet PSE Industrial Switch   PoE feature is more often supported in the industrial Ethernet devices for efficient operation in harsh environments. The ISW-504PT in-line power follows standard IEEE 802.3af and allows giving power to 4 PoE compliant devices at the distance up to 100 meters through the 4-pair Cat 5 / 5e UTP wire. With Data and Power over Ethernet from one unit, the ISW-504PT shall reduce cables deployment and eliminates the need for dedicated electrical outlets on the wall, ceiling or any unreachable place. A wire carries both data and (power lowering), the installation costs, simplifying the installation effort and eliminating the need for electricians or extension cords.Furthermore, there is only 24V DC input in some industrial environments, the ISW-504PT series supports 24V DC or 48V DC dual voltages input and able to provide more wide range of industrial IEEE 802.3af PoE applications.   Wide Temperature conquers installation in harsh environments The ISW-504PT provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under wide temperature range from -40 to 75 Degree C, the ISW-504PT can be placed in almost any difficult environment. It also offers dual-redundant, reversible polarity 24V DC or 48V DC power inputs for high availability applications requiring backup power inputs.     Robust Switch performance The ISW-504PT offers high performance switch architecture with 5 10/100Mbps UTP ports. It provides non-blocking switch fabric, wire-speed throughput as high as 1Gbps and the 2K MAC Address table. It also performs wire-speed packets transfer without risk of packet loss and the Flow Control function is default enabled to provide fast and reliable data transfer. All of the RJ-45 copper interfaces support 10/100Mbps Auto-Negotiation for optimal speed detection through RJ-45 Category 3, 4, 5, 5e or 6 cable. The standard Auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.

• 4-port 10/100Base-TX RJ-45 with auto MDI/MDI-X function
• 1-port 100Base-FX interface for up to 2km (Multi-mode fiber 50µm/125µm) on ISW-511
• 1-port 100Base-FX interface for up to 15km (Single-mode fiber 9µm/125µm) on ISW-511S15

  Layer 2 Features

• Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Ethernet standard
• Supports auto negotiation and 10/100Mbps half / full duplex mode for each copper port
• High performance Store and Forward architecture
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (Switching Fabric): 1Gbps
• Integrated address look-up engine, support 2K absolute MAC addresses
• 1 Mbit on-chip frame buffer
• Automatic address learning and address aging
• CSMA/CD Protocol

  Industrial Case / Installation

• IP-30 metal case / protection
• DIN rail and wall mount design
• 12 to 48V DC, redundant power with polarity reverse protect function and connective removable terminal block for master and slave power
• Supports EFT protection 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -10 to 60 degrees C operating temperature 

    New slim type with more practicability and convenience PLANET has released the ISW-511 / ISW-511S15, an advanced industrial hardened Ethernet Switch with new slim type, IP-30 metal case. They each are equipped with 4 10/100Base-TX auto-negotiation ports. The ISW-511 has one 100Base-FX multi-mode SC interface for transmission distance up to 2km, and the ISW-511S15 has one 100Base-FX single-mode SC interface for transmission distance up to 15km. Both of them operate reliably in Heavy Industrial demanding environments. The compact, IP-30 standard metal case allows either DIN rail or wall mounting for efficient use of cabinet space.   Stable Operating Performance under Difficult Environments The ISW-511 / ISW-511S15 provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -10 to 60 degrees C, the ISW-511 / ISW-511S15 can be placed in almost any difficult environment. The ISW-511 / ISW-511S15 also possesses an integrated power supply source with wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust Switch performance The ISW-511 / ISW-511S15 each provides four 10/100Base-TX Ethernet ports and one 100Base-FX optic-fiber SC interface, and boasts a high performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 1Gbps. With 2K MAC address table, they offer wire-speed packets transfer performance without risk of packet loss. The Flow Control function allows the ISW-511 / ISW-511S15 for fast and reliable data transfer.   All of the RJ-45 copper interfaces in the ISW-511 / ISW-511S15 support 10/100Mbps auto negotiation for optimal speed detection through RJ-45 Category 3, 4 or 5 cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.

• 8-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function

  Layer 2 Features

• Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX Ethernet standard
• Supports auto-negotiation and 10/100Mbps half/full duplex mode
• High performance Store and Forward architecture; runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (switching fabric): 1.6Gbps
• Integrated address look-up engine, supporting 1K absolute MAC addresses
• Automatic address learning and address aging

  Industrial Case & Installation

• IP30-rated metal case
• DIN rail and wall-mount design
• 12 to 48V DC, redundant power with polarity reverse protection function and connective removable terminal block for master and slave power, 24V AC power support
• Lower Power Consumption device in full load operation mode
• Supports EFT protection for 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 degrees C operating temperature
• Free fall, shock-proof and vibration-proof for industries

   Slim Type with more Practicability and Convenience PLANET ISW-801T, an Industrial 8-port Fast Ethernet Switch, provides non-blocking wire-speed performance in harsh industrial environment. It also provides 8-port 10/100BASE-TX RJ45 copper interfaces delivered in an IP30 rugged, strong case with redundant power system. Its slim case is suitable for such applications as surveillance system deployments, control management and wireless service in climatically demanding environments with wide temperature range from -40 to 75 degrees C.   Energy Saving with Lower Power Consumption The ISW-801T, adopting the advanced green networking technology, provides the IEEE 802.3az protocol based power saving. This feature makes the ISW-801T consume very low power in full load operation mode, which helps conserve energy effectively but maintains high performance efficiently.   Stable Performance under Difficult Environments The ISW-801T provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb-side traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C, the ISW-801T can be placed in almost any difficult environment. The ISW-801T also possesses an integrated power supply source with wide range of voltages (12 to 48V DC, 24V AC) for worldwide high availability applications requiring dual or backup power inputs.    Robust Switch Performance Built in a high-performance switch architecture, the ISW-801T comes with eight 10/100Mbps Fast Ethernet ports providing non-blocking switch fabric and wire-speed throughput as high as 1.6Gbps, and the 1K MAC address. Thus, the ISW-801T can transfer wire-speed packets without the risk of packet loss. The flow control function enables the ISW-801T to provide fast and reliable data transfer.   All of the RJ45 copper interfaces in the ISW-801T support 10/100Mbps auto negotiation for optimal speed detection through RJ45 Category 5 or 5e cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight-through or crossover cables.

• Speziell für raue Umgebungen entwickelt
• CCTV, Fabrik, Küstengebiete, staubige Umgebung usw.
• Drei verschiedene Modelle erfüllen die Anforderungen verschiedener Geschäftsszenarien
• Einzigartiges Industriedesign gewährleistet stabilen Betrieb bei -40℃ bis 80℃
• 8 KV Schutz: Die Abschirmung gegen Spannungsspitzen
• IP40 gegen 1mm Eindringlinge in staubigen Bedingungen
• ERPS Plug-and-Play, ohne komplizierte Konfiguration
• Lokales Netzwerk SON, einfache Konfiguration auch ohne Cloud
• Ruijie Cloud: Einfaches Management auch in rauen Umgebungen

• Speziell für raue Umgebungen entwickelt
• CCTV, Fabrik, Küstengebiete, staubige Umgebung usw.
• Drei verschiedene Modelle erfüllen die Anforderungen verschiedener Geschäftsszenarien
• Einzigartiges Industriedesign gewährleistet stabilen Betrieb bei -40℃ bis 80℃
• 8 KV Schutz: Die Abschirmung gegen Spannungsspitzen
• IP40 gegen 1mm Eindringlinge in staubigen Bedingungen
• ERPS Plug-and-Play, ohne komplizierte Konfiguration
• Lokales Netzwerk SON, einfache Konfiguration auch ohne Cloud
• Ruijie Cloud: Einfaches Management auch in rauen Umgebungen

• Speziell für raue Umgebungen entwickelt
• CCTV, Fabrik, Küstengebiete, staubige Umgebung usw.
• Drei verschiedene Modelle erfüllen die Anforderungen verschiedener Geschäftsszenarien
• Einzigartiges Industriedesign gewährleistet stabilen Betrieb bei -40℃ bis 80℃
• 8 KV Schutz: Die Abschirmung gegen Spannungsspitzen
• IP40 gegen 1mm Eindringlinge in staubigen Bedingungen
• ERPS Plug-and-Play, ohne komplizierte Konfiguration
• Lokales Netzwerk SON, einfache Konfiguration auch ohne Cloud
• Ruijie Cloud: Einfaches Management auch in rauen Umgebungen

• 5-Port 10/100/1000BASE-T Gigabit RJ45-Kupfer mit IEEE 802.3at/af PoE-Injektor (Port 1 bis Port 4)
• Bandbreite (non-blocking): 10 Gbit/s
• Gesamt-PoE-Leistungsbudget: 120W
• Vollaluminiumgehäuse
• Hutschienen- oder Wandmontage
• -40°C bis +75°C

  TSW100 - 5-Port, unmanaged Gigabit-Ethernet-Switch mit Power over Ethernet Unterstützung (802.3af- und 802.3at-Standards) Dieses Gerät ist als Power Source Equipment (PSE) klassifiziert. Bei Verwendung auf diese Weise ermöglicht der TSW100-Switch die Zentralisierung der Stromversorgung, liefert bis zu 30 Watt Leistung pro Port und reduziert den Aufwand für die Installation einer Stromversorgung. Er verfügt über Ethernet-Ports mit 10/100/1000 Mbit/s, um eine wirtschaftliche Lösung mit hoher Bandbreite für Ihr Industrial Ethernet Netzwerk bereitzustellen.

• 5-Port 10/100/1000BASE-T Gigabit RJ45-Kupfer mit IEEE 802.3at/af PoE-Injektor (Port 1 bis Port 4)
• Bandbreite (non-blocking): 10 Gbit/s
• Gesamt-PoE-Leistungsbudget: 60W
• Vollaluminiumgehäuse
• Hutschienen- oder Wandmontage
• -40°C bis +75°C

• TSW101 ist der erste unmanaged Switch von Teltonika Networks für Automobile.
• Ausgestattet mit fünf Gigabit-Ethernet-Ports, von denen vier die Standards IEEE802.3af und IEEE802.3at PoE+ unterstützen.
• Eine große Auswahl an unterstützten Versorgungsspannungen (9-30 VDC) und eine kompakte Größe ermöglichen den Einbau in viele Automobilanwendungen.
• Dieses als Power Source Equipment (PSE) klassifizierte Gerät ermöglicht eine Zentralisierung der Stromversorgung – mit bis zu 30 Watt pro einzelnem Port und einer maximalen Ausgangsleistung von 60 Watt.
• 10/100/1000-Mbit/s-Ethernet-Ports für optimierte Lösungen mit hoher Bandbreite.
• Ideal, um beides bereitzustellen: Stromversorgung im Fahrzeug und gleichzeitig eine Ethernet-Datenverbindung.

• 5 Gigabit Ethernet Ports
• 10Gbps Bandbreite (nicht blockierend)
• Plug-and-Play
• Robustes Aluminiumgehäuse
• 4-Pin Stecker zur Versorgung (mit 1x Dig. In u. 1x Dig. Out)
• Passiv POE-In auf Port 1

Der TSW110 ist ein Layer-2-Unmanaged-Switch, der eine vereinfachte Version des TSW100 darstellt. Er kann über den ersten LAN-Port mit Strom versorgt werden und verfügt über fünf 10/100/1000-Mbit/s-Ethernet-Ports für eine wirtschaftliche Lösung mit hoher Bandbreite.Er bietet eine breite Palette an unterstützten Versorgungsspannungen (9-30 V). Ideal für professionelle Anwendungen mit hoher Bandbreite für eine zuverlässige Datenverbindung.  

• 8-Port 10/100/1000BASE-T Gigabit RJ45-Kupfer mit IEEE 802.3at/af PoE-Injektor
• Bandbreite (non-blocking): 20 Gbit/s
• Gesamt-PoE-Leistungsbudget: 240W
• Vollaluminiumgehäuse
• Hutschienen- oder Wandmontage
• -40°C bis +75°C

TSW200 ist ein industrieller Unmanaged Switch von Teltonika Networks. TSW200 ist mit 2 SFP-Ports für die Glasfaserkommunikation über große Entfernungen und 8 Gigabit-Ethernet-Ports ausgestattet, die die Power-over-Ethernet-Standards IEEE802.3af und IEE802.3at unterstützen. Als Power Source Equipment (PSE) klassifiziert, ermöglicht es eine Zentralisierung der Stromversorgung, stellt bis zu 30 Watt pro Port bereit und reduziert den Installationsaufwand. Es verfügt über 10/100/1000-Mbit/s-Ethernet-Ports, um eine wirtschaftliche Lösung mit hoher Bandbreite für Ihr industrielles Ethernet-Netzwerk bereitzustellen. Dieser robuste, unmanaged Industrie-Switch ist ideal für professionelle Anwendungen mit hoher Bandbreite, bei denen beides erforderlich ist: zuverlässige Datenverbindung und Stromversorgung.

• 8-Port 10/100/1000BASE-T Gigabit RJ45-Kupfer 
• 2x SFP Port
• Bandbreite (non-blocking): 20 Gbit/s
• Vollaluminiumgehäuse
• Hutschienen- oder Wandmontage
• -40°C bis +75°C

Der TSW210 ist ein industrieller Unmanaged Switch zur Zentralisierung Ihrer Ressourcen. Ausgestattet mit 2 SFP-Ports für Glasfaserkommunikation mit großer Reichweite und 8 Gigabit-Ethernet-Ports mit bis zu 1000 Mbit/s Download-/Upload-Geschwindigkeit. Das langlebige, robuste Aluminiumgehäuse mit DIN-Schienen- und Oberflächenmontageoptionen machen den TSW210 perfekt für industrielle Umgebungen. 2-polige industrielle DC-Steckdose mit einem Eingangsspannungsbereich von 7-57 VDC.

• 8-Port 10/100/1000BASE-T Gigabit RJ45-Kupfer 
• 2x SFP Port
• Bandbreite (non-blocking): 20 Gbit/s
• Vollaluminiumgehäuse
• Hutschienen- oder Wandmontage
• -40°C bis +75°C

Der TSW212 ist ein L2 Managed Ethernet-Switch mit zusätzlichen L3-Funktionen wie DHCPv6-Client-Unterstützung und statischem IPv6-Routing. Dieser Switch unterstützt Protokolle wie EtherNet/IP, PROFINET und MRP und verfügt über 8 Gigabit Ethernet-Ports und 2 SFP-Ports für eine robuste Glasfaserkommunikation mit großer Reichweite. Managed Switch:
L2 mit zusätzlichen L3-Funktionen für erweiterte Managementmöglichkeiten Profinet & mehr:
Unterstützt Profinet für die automatisierte Datenverarbeitung sowie weitere Protokolle wie EtherNet/IP und MRP Ethernet & SFP:
8 x Gigabit Ethernet Ports und 2 x SFP Ports für Glasfaserkommunikation WitchOS:
Teltonika Networks OS für Switches, intuitiv gestaltet für unbegrenzte Konfigurationen

• 4-Port 10/100/1000BASE-T Gigabit RJ45-Kupfer 
• Passive-PoE In
• Bandbreite (non-blocking): 8 Gbit/s
• Vollaluminiumgehäuse
• Hutschienenmontage
• -40°C bis +75°C

• Der TSW304 ist der erste Unmanaged Switch von Teltonika Networks mit integrierter, eingebauter DIN-Hutschienenhalterung.
• Ausgestattet mit vier Gigabit-Ethernet-Ports, die die Ethernet-Standards IEEE 802.3, IEEE 802.3u und 802.3az unterstützen.
• Der TSW304 wurde im Hinblick auf eine einfache Installation entwickelt und verfügt über eine kompakte Größe mit einem stoßfesten Gehäuse, das mit seiner integrierten DIN-Halterung einhergeht.
• 10/100/1000-Mbit/s-Ethernet-Ports für wirtschaftliche Lösungen mit hoher Bandbreite für zuverlässigen Datendurchsatz.
• 2-polige Industriesteckdose und breite Palette unterstützter Versorgungsspannungen (7-57 VDC und 9-40 VAC).