• Hot Swap power supply for CCR1072
• No need for Router reboot

  CCR1072-1G-8S+ is equipped with two redundant Hot Swap 12v 150W AC/DC power supplies - if one of them goes out of order, second one will take over. Hot Swap 12v 150W AC/DC power supplies for CCR1072-1G-8S+ are now available for purchase separately. You can replace them on the go to ensure zero downtime, no need to even restart the router!

• 24V/1.6A
• Suitable for all Routerboards

  The MikroTik 24V/1.6A power adapter can be used on all common RouterBOARD models.

• Internal Power Supply
• 24V/1.6A
• Suitable for CCR1009-7G-1C-1S+ & CRS317-1G-16S+RM

   

• 48V/1.46A
• for Routerboard RB800

  The MikroTik 48V / 1,46A Power supply can be used to RB800.

• 48V/2A
• for Routerboard CRS112-8P-4S-IN, hEX PoE

  The MikroTik 48V / 2A Power supply can be used to CRS112-8P-4S-IN or hEX PoE. It’s providing 30% more current than the old model 48POW (48 V 1.46 A 70 W), allowing more power per port.

• 5V, 1A Power Supply
• MicroUSB Connector
• Suitable for:
• hAP mini
• hAP lite
• cAP lite

5V power injector for USB, is just injector cable, 5V power supplies must be sourced locally - we do not sell those.   Accepts DC Plug, 1.1MM x 3.5MM

• passive PoE
• Input 12-28V
• Max 1A
• Ethernet 10/100/1000

  The mUPS is a PoE injector with battery backup capability with a 12 V battery connector. It works just like a Gigabit PoE injector, but when power is lost, it switches over to the 12 V battery. Even if your power source is 28 V, the connected RouterBOARD will not reboot when the power source is lost, it will switch over to the 12 V battery transparently. The LEDs indicate DC line or battery usage, the charging of battery and low battery level (<50%).   In RouterOS it is possible to detect when running on battery power by monitoring the input voltage with scripting, since the voltage will change without a RouterOS reboot.   The mUPS is a simple and compact device to make your network more reliable, or for situations where stable power input is not available, like solar or automotive installations. You can use the mUPS with any single 12V battery (AGM, Gel, Lead Acid, regular car batteries, deep cycle marine batteries, etc.).   Note: 12 V battery not included and must be mounted elsewhere.  

• 10/100/1000 Ethernet ports: 2
• Short detection time: ~50us
• Short protection delay: ~20ms
• After short recovery time: ~1s
• Measurement update time: ~45ms
• PoE in 12 - 28 V
• DC in 12 - 28 V
• Battery connector: Female tab terminal 6.3 x 0.8 mm
• Battery charging current: 1 A max
• Poe out max current limit: 1 A

• 24V/0.8A
• Suitable for all Routerboards

  The MikroTik 24V/0.8A power adapter can be used on all common RouterBOARD models.

• Hot Swap power supply for CCR1072
• No need for Router reboot

  Hot Swap -48v 150W DC power supplies for CCR1072-1G-8S+ are now available for purchase separately. You can replace them on the go to ensure zero downtime, no need to even restart the router!

• passive PoE
• Input 9-48V
• Max 2A
• Ethernet Cable Length up to 60m
• Ethernet 10/100/1000

  The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device.   Helps reducing number of wires that lead up the tower.   For using with any RouterBOARD that supports 9-48V PoE.   The GPOE has shielded connectors.

• 48 to 24V
• 10/100/1000Mbit/s
• Gigabit PoE Converter
• 802.3af support
• 802.3at PoE plus support

  This device lets you use any 48V PoE source (including Passive PoE, Telecom PoE, 802.3af and 802.3at) to power RouterBOARD devices.   Simply plug any 48V PoE powered ethernet cable into one port, and any 8-30V capable RouterBOARD device into the other. This device is capable to provide high power output - up to 24W (up to 1A at 24V).   You can power it with virtually any 42-57V PoE solutions available on market today (Passive, Telecom, 802.3af and 802.3at PoE plus supported)   The device is a rugged metallic design, with high quality components and integrated heatsink design. The case also has mounting holes so you can attach it to a wall.   Ethernet shield pins are inside the Ethernet connectors, so that shielded ethernet can be used, to ground either at the converter itself, or at the devices at both ends. Supports 10/100/1000Mbps Ethernet

• passive PoE
• Max 2A
• Ethernet Cable Length up to 60m
• Ethernet 10/100

  Low-cost passive PoE base unit for powering passive PoE devices over ethernet. Simply connect your power source to the injector, and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires that lead up the tower, and in other situations.   For using with RouterBOARDS that support 10-28V PoE powering, input needs to be at least 18V to accomodate any losses in cables.

This device lets you use any 48V PoE source (including Passive PoE, Telecom PoE, 802.3af and 802.3at) to power RouterBOARD devices.   Simply plug any 48V PoE powered ethernet cable into one port, and any 8-30V capable RouterBOARD device into the other. This device is capable to provide high power output - up to 24W (up to 1A at 24V).   You can power it with virtually any 42-57V PoE solutions available on market today (Passive, Telecom, 802.3af and 802.3at PoE plus supported) The device is a rugged metallic design, with high capacity components and integrated heatsink design. The case also has mounting holes so you can attach it to a wall.   Ethernet shield pins are inside the Ethernet connectors, so that shielded ethernet can be used, to ground either at the converter itself, or at the devices at both ends.