• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard • Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568 • One fiber-optic, 1310nm wavelength, connector type and distance vary with model    - FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm    - FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm • Data Transfer Rate:   - TP: 10/100Mbps     - FX: 100Mbps • Duplex mode support:  - Full or half-duplex mode by auto-negotiation (TP)   - Full or half-duplex mode by DIP switch (FX) • LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL • DIP switch: 2 DIP switches   - Rear DIP switch: FX duplex mode selection   - Side DIP switch: LFP (Link Fault Pass-through) mode selection • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets     PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard • Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568 • One fiber-optic, 1310nm wavelength, connector type and distance vary with model    - FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm    - FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm • Data Transfer Rate:   - TP: 10/100Mbps     - FX: 100Mbps • Duplex mode support:  - Full or half-duplex mode by auto-negotiation (TP)   - Full or half-duplex mode by DIP switch (FX) • LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL • DIP switch: 2 DIP switches   - Rear DIP switch: FX duplex mode selection   - Side DIP switch: LFP (Link Fault Pass-through) mode selection • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets     PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• 1-port 10/100Base-T RJ-45 with auto negotiation and auto-MDI/MDI-X function • 1 100Base-FX SC interface, providing long distance up to 2km on IFT-802T • 1 100Base-FX SC interface, providing long distance for 15km on IFT-802TS15 • 1 Mini-GBIC slot, providing multi choice of SFP modules on IFT-805AT   Industrial Conformance • 12V to 48V DC, redundant power with polarity reverse protect function • -40 to 75 degrees C operating temperature • IP30 metal case • Relay alarm for port breakdown • Supports 6KV DC Ethernet ESD protection • Supports 6KV DC EFT protection for power line • Free Fall, Shock and Vibration Stability • DIN-rail and wall-mountable hardware design   Layer 2 Features • Complies with the IEEE 802.3, IEEE 802.3u Fast Ethernet standard • Auto-MDI / MDI-X detection and auto negotiation in half-duplex / full-duplex modes for 10 /100Base-TX RJ-45 port • Store-and-Forward Switching Architecture • Features Store-and-Forward mode with wire-speed filtering and forwarding rates • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • Supports packet size of up to 1522bytes • CSMA/CD Protocol • Automatic source address learning and aging   Distance Extension with High Performance and Steady Network Communication PLANET 10/100Base-TX to 100Base-FX Industrial Media Converter IFT-80xT series extends communication distance with stable performance via fiber optic wire, in which the extended distance could be up to 2km with the IFT-802T, up to 15km with the IFT-802TS15 or up to 20km with the IFT-805AT (depending on SFP module). The IFT-80xT series is specifically equipped with durable components and strong housing case to operate reliably in electrically harsh and climatically demanding environments. The industrial level media converter provides a high level of immunity to electromagnetic interference and heavy electrical surges which are usually found on plant floors or traffic control cabinets on sidewalk. Being able to operate under the temperature range from -40 to 75 degrees C allows the IFT-80xT series to be placed in almost any difficult environment.   Robust Media Converter Performance PLANET IFT-80xT 10/100Base-TX to 100Base-FX Industrial Media Converter series efficiently converts data between 10/100Base-TX and 100Base-FX network. The IFT-80xT series provides the flexibility to all kinds of 10/100Mbps Ethernet Media on RJ-45 port and performs highly stable fiber performance.   Easy Installation and Wide Range of Power Usages The IFT-80xT series is packaged in a compact IP-30 case that allows either DIN rail or panel mounting to have efficient usage of cabinet space. It provides an integrated power supply with a wide range of voltages for worldwide operation. It also offers dual-redundant, reversible polarity 12V DC to 48V DC power supply inputs for high availability applications requiring dual or backup power inputs.   

• 1-port 10/100Base-T RJ-45 with auto negotiation and auto-MDI/MDI-X function • 1 100Base-FX SC interface, providing long distance up to 2km on IFT-802T • 1 100Base-FX SC interface, providing long distance for 15km on IFT-802TS15 • 1 Mini-GBIC slot, providing multi choice of SFP modules on IFT-805AT   Industrial Conformance • 12V to 48V DC, redundant power with polarity reverse protect function • -40 to 75 degrees C operating temperature • IP30 metal case • Relay alarm for port breakdown • Supports 6KV DC Ethernet ESD protection • Supports 6KV DC EFT protection for power line • Free Fall, Shock and Vibration Stability • DIN-rail and wall-mountable hardware design   Layer 2 Features • Complies with the IEEE 802.3, IEEE 802.3u Fast Ethernet standard • Auto-MDI / MDI-X detection and auto negotiation in half-duplex / full-duplex modes for 10 /100Base-TX RJ-45 port • Store-and-Forward Switching Architecture • Features Store-and-Forward mode with wire-speed filtering and forwarding rates • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • Supports packet size of up to 1522bytes • CSMA/CD Protocol • Automatic source address learning and aging   Distance Extension with High Performance and Steady Network Communication PLANET 10/100Base-TX to 100Base-FX Industrial Media Converter IFT-80xT series extends communication distance with stable performance via fiber optic wire, in which the extended distance could be up to 2km with the IFT-802T, up to 15km with the IFT-802TS15 or up to 20km with the IFT-805AT (depending on SFP module). The IFT-80xT series is specifically equipped with durable components and strong housing case to operate reliably in electrically harsh and climatically demanding environments. The industrial level media converter provides a high level of immunity to electromagnetic interference and heavy electrical surges which are usually found on plant floors or traffic control cabinets on sidewalk. Being able to operate under the temperature range from -40 to 75 degrees C allows the IFT-80xT series to be placed in almost any difficult environment.   Robust Media Converter Performance PLANET IFT-80xT 10/100Base-TX to 100Base-FX Industrial Media Converter series efficiently converts data between 10/100Base-TX and 100Base-FX network. The IFT-80xT series provides the flexibility to all kinds of 10/100Mbps Ethernet Media on RJ-45 port and performs highly stable fiber performance.   Easy Installation and Wide Range of Power Usages The IFT-80xT series is packaged in a compact IP-30 case that allows either DIN rail or panel mounting to have efficient usage of cabinet space. It provides an integrated power supply with a wide range of voltages for worldwide operation. It also offers dual-redundant, reversible polarity 12V DC to 48V DC power supply inputs for high availability applications requiring dual or backup power inputs.   

• 1-port 10/100Base-T RJ-45 with auto negotiation and auto-MDI/MDI-X function • 1 100Base-FX SC interface, providing long distance up to 2km on IFT-802T • 1 100Base-FX SC interface, providing long distance for 15km on IFT-802TS15 • 1 Mini-GBIC slot, providing multi choice of SFP modules on IFT-805AT   Industrial Conformance • 12V to 48V DC, redundant power with polarity reverse protect function • -40 to 75 degrees C operating temperature • IP30 metal case • Relay alarm for port breakdown • Supports 6KV DC Ethernet ESD protection • Supports 6KV DC EFT protection for power line • Free Fall, Shock and Vibration Stability • DIN-rail and wall-mountable hardware design   Layer 2 Features • Complies with the IEEE 802.3, IEEE 802.3u Fast Ethernet standard • Auto-MDI / MDI-X detection and auto negotiation in half-duplex / full-duplex modes for 10 /100Base-TX RJ-45 port • Store-and-Forward Switching Architecture • Features Store-and-Forward mode with wire-speed filtering and forwarding rates • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • Supports packet size of up to 1522bytes • CSMA/CD Protocol • Automatic source address learning and aging   Distance Extension with High Performance and Steady Network Communication PLANET 10/100Base-TX to 100Base-FX Industrial Media Converter IFT-80xT series extends communication distance with stable performance via fiber optic wire, in which the extended distance could be up to 2km with the IFT-802T, up to 15km with the IFT-802TS15 or up to 20km with the IFT-805AT (depending on SFP module). The IFT-80xT series is specifically equipped with durable components and strong housing case to operate reliably in electrically harsh and climatically demanding environments. The industrial level media converter provides a high level of immunity to electromagnetic interference and heavy electrical surges which are usually found on plant floors or traffic control cabinets on sidewalk. Being able to operate under the temperature range from -40 to 75 degrees C allows the IFT-80xT series to be placed in almost any difficult environment.   Robust Media Converter Performance PLANET IFT-80xT 10/100Base-TX to 100Base-FX Industrial Media Converter series efficiently converts data between 10/100Base-TX and 100Base-FX network. The IFT-80xT series provides the flexibility to all kinds of 10/100Mbps Ethernet Media on RJ-45 port and performs highly stable fiber performance.   Easy Installation and Wide Range of Power Usages The IFT-80xT series is packaged in a compact IP-30 case that allows either DIN rail or panel mounting to have efficient usage of cabinet space. It provides an integrated power supply with a wide range of voltages for worldwide operation. It also offers dual-redundant, reversible polarity 12V DC to 48V DC power supply inputs for high availability applications requiring dual or backup power inputs.   

• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard • Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568 • One fiber-optic, 1310nm wavelength, connector type and distance vary with model   - FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm   - FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm • Data Transfer Rate:   - TP: 10/100Mbps      - FX: 100Mbps • Duplex mode support:     - Full or half-duplex mode by auto-negotiation (TP) - Full or half-duplex mode by DIP switch (FX) • LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL • DIP switch: 2 DIP switches - Rear DIP switch: FX duplex mode selection - Side DIP switch: LFP (Link Fault Pass-through) mode selection • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets   PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard • Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568 • One fiber-optic, 1310nm wavelength, connector type and distance vary with model   - FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm   - FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm • Data Transfer Rate:   - TP: 10/100Mbps      - FX: 100Mbps • Duplex mode support:     - Full or half-duplex mode by auto-negotiation (TP) - Full or half-duplex mode by DIP switch (FX) • LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL • DIP switch: 2 DIP switches - Rear DIP switch: FX duplex mode selection - Side DIP switch: LFP (Link Fault Pass-through) mode selection • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets   PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard
• Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568
• LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL
• IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets
• One fiber-optic, 1310nm wavelength, connector type and distance vary with model
• FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm
• FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm
• Data Transfer Rate:
• TP: 10/100Mbps
• FX: 100Mbps
• Duplex mode support:
• Full or half-duplex mode by auto-negotiation (TP)
• Full or half-duplex mode by DIP switch (FX)
• DIP switch: 2 DIP switches
• Rear DIP switch: FX duplex mode selection
• Side DIP switch: LFP (Link Fault Pass-through) mode selection

  PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u, 100BASE-TX and 100BASE-FX Ethernet standards
• One 10/100BASE-TX port with RJ45 connector
• One 100BASE-FX port with ST/SC/WDM connector supporting multi-mode or single-mode fiber optic cable
• Auto-negotiation and auto-MDI / MDI-X for 10/100BASE-TX port
• Back-pressure and IEEE 802.3x compliant flow control and full wire-speed forwarding rate
• Link Loss Return (LLR) switch on each fiber optic is to aid in troubleshooting remote network connections
• Link Loss Carry Forward (LLCF) works with LLR in diagnosing network connections

  Distance Extended with Fiber Optic Cable PLANET FST-80x Smart Media Converter series provides media conversion between 10/100BASE-TX and 100BASE-FX interfaces, such as multi-mode ST/SC connectors (2km), single-mode SC connector (15/35/50km) and single fiber connector using the wavelength-division multiplexing (WDM) technology (20/60km) to enable to extend links over long distances using fiber optic cable.    Enhanced Smart Management Features The FST-80x series provides auto MDI/MDI-X on their TP port and store-and-forward mechanism to eliminate faulty packets. Use the DIP switch from the FST-80x to configure the available smart functions, such as the half/full duplex, auto-negotiation / force and 10/100Mbps options for TP and fiber interfaces. Besides, the Link Loss Return (LLR) and Link Loss Carry Forward (LLCF) functions can immediately alarm network administrator once there is a media link issue, thus helping to monitor the status of the entire network.    Easy Installation The FST-80x series can be connected easily and cost-effectively as these smart media converters can be used as a standalone unit when powered on by its DC adapter, or used as a slide-in module connected to PLANET 19-inch, 16-slot web smart/managed media converter chassis (MC-1600MR/MC-1600MR48 and MC-1610MR/MC-1610MR48). When working with the web smart/managed media converter chassis, the status of the FST-80x can be monitored via the local RS-232 console and remote web interface.

• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard • Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568 • One fiber-optic, 1310nm wavelength, connector type and distance vary with model   - FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm   - FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm • Data Transfer Rate:   - TP: 10/100Mbps      - FX: 100Mbps • Duplex mode support:     - Full or half-duplex mode by auto-negotiation (TP) - Full or half-duplex mode by DIP switch (FX) • LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL • DIP switch: 2 DIP switches - Rear DIP switch: FX duplex mode selection - Side DIP switch: LFP (Link Fault Pass-through) mode selection • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets   PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• 100-Gigabit Ethernet Verbindungen
• QSFP28-Modul für Entfernungen bis 100m
• niedriger Stromverbrauch
• geringe Latenzen

Verwenden Sie dieses QSFP-Modul für Entfernungen bis zu 100 Metern zu Ihren CCR2216-, CRS504- oder CRS518-Setups hinzu und genießen Sie echte Geschwindigkeit und ultimative Zuverlässigkeit. Dieses optische Modul bietet vier unabhängige Vollduplex-Kanäle mit bis zu 25 Gbit/s Bandbreite pro Kanal und einer Gesamtbandbreite von 100 Gbit/s. Das Modul verfügt über integrierte digitale Diagnosefunktionen wie optische Leistungsüberwachung.

• 100-Gigabit Ethernet Verbindungen
• QSFP28 Direct Attach Kabel
• 1m oder 3m Kabellänge
• niedriger Stromverbrauch
• geringe Latenzen

Verbinden Sie problemlos zwei beliebige MikroTik 100-Gigabit-Helden (CCR2216 und CRS504) - dieses Kabel verfügt über integrierte QSFP28-Module. Einfach einstecken und die Geschwindigkeit genießen! Das Kabel ist einen Meter lang, was für die meisten Setups ausreichen sollte, es ist aber auch eine 3-Meter-Version erhältlich. Es ist ziemlich flexibel – Sie können Ihre Geräte getrennt oder übereinander halten

• Cost-Effective VDSL2 Profile 17a/30a CO / CPE bridge solution • One box design, CO / CPE selectable via DIP Switch • Defines symmetric band plan for the transmission of upstream and downstream signals • Complies with IEEE 802.3, 10Base-T, IEEE 802.3u, 100Base-TX and IEEE 802.3x, Flow control Ethernet 　standards • DMT (Discrete Multi-Tone) line coding • Half duplex Back pressure and IEEE 802.3x Full Duplex Pause frame flow control • Built-in POTS splitter to share voice and data • Two RJ-11 connectors for each VDSL port, one for VDSL connection and one for POST connection • Voice and data communication can be shared simultaneously based on the existing telephone wire • Four 10/100Mbps RJ-45 port, Auto-Negotiation and Auto-MDI/MDI-X • Supports up to 1536 bytes packet size, IEEE 802.1Q VLAN tag transparent • Hardware IGMP Snooping for Multimedia service • VDSL2 stand-alone transceiver for simple bridge modem application • Advantage of minimum installation time (Simply as Plug-and-Play) • Selectable target profile and target SNR margin • Supports extensive LED indicators for network diagnosis   100/100Mbps Downstream / upstream, high Performance Ethernet over VDSL Solution PLANET VC-234 is an Ethernet-over-VDSL2 Bridge with high performance. It is designed based on two core networking technology, Ethernet and VDSL2 (Very-high-data-rate Digital Subscriber Line 2). The VDSL2 technology offers absolutely fastest data transmission speed over existing copper telephone lines without the need of rewiring. The VC-234 supports ultra-high performance to the pervasive telephone line network with up to 100/100Mbps symmetric data rate within 300m and 20/4Mbps for 1.4km long range connections.     Implementing with Existing Telephone Copper Wires The VC-234 is also a Long Reach Ethernet (LRE) Bridge providing four RJ-45 Ethernet ports and two RJ-11 phone jacks, in which one is for VDSL connection and the other one is for POTS (Plain Old Telephone Service) connection. The VC-234 has built-in POTS splitter to share the existing phone line with POTS; therefore it is no need of replacing the existing copper wiring. Just plug the VC-234 into the existing RJ-11 telephone jack and a high-performance VDSL2 network can be connected. The VC-234 is ideal to be used as an Ethernet extender to an existing Ethernet network.   Delivering High-Demand Service Connectivity for ISP / Triple Play Devices The VC-234 provides excellent bandwidth to satisfy the triple play devices for home entertainment and communication. With the capability of 100/100Mbps symmetric data transmission, the VC-234 enables many multi-media services to work on the local Internet, such as VOD (Video on Demand), Voice over IP, Video phone, IPTV, Internet caching server, distance education, and so on.   Easy & Flexible Installation The Ethernet-over-VDSL2 Bridge comes with a plug-and-play design and is fully compatible with all kinds of network protocols. Moreover, the operating status of each individual port and the whole system can be watched via the rich diagnostic LEDs on the front panel. The VC-234 offers two modes, CPE and CO, for application: CPE mode is used at client side and CO mode is at central side. The CPE or CO mode can be adjusted by using a built-in DIP switch. For point-to-point connection, a CPE mode VC-234 and a CO mode VC-234 must be setup as one pair of converters to perform the connection.   Providing Superior Upstream and Downstream Transmission Performance The VC-234 also defines symmetric band plan for the transmission of upstream and downstream signals; the band plan performs higher transmission quality in short range for central side (CO) in symmetric mode. In all, when the VC-234 is in profile 17a operation mode, it provides long distance transmit with Ultra-high performance to the pervasive telephone line network, and when the VC-234 is in 30a operation mode, it gives short distance transmits with upstream and downstream transmission giving wire speed performance.

- Kosteneffiziente VDSL2 Profil 17a/30a CO / CPE Brückenlösung
nur kompatibel mit VC-201A/204/231 und 234 - Ein-Gehäuse-Design, CO / CPE wählbar über DIP-Schalter
- Definiert einen symmetrischen Bandplan für die Übertragung von Upstream- und Downstream-Signalen
- Entspricht IEEE 802.3, 10Base-T, IEEE 802.3u, 100Base-TX und IEEE 802.3x, Flow control Ethernet
　Normen
- DMT (Diskreter Mehrton) Leitungscodierung
- Halbduplex-Rückdruck und IEEE 802.3x-Vollduplex-Pausenrahmen-Flusskontrolle
- Ein RJ-11-Anschluss für VDSL-Port mit VDSL-Anschluss, zusätzlicher Splitter für POST-Anschluss
- Sprach- und Datenkommunikation können gleichzeitig auf Basis der vorhandenen Telefonleitung genutzt werden
- Ein 10/100Mbps RJ-45 Anschluss, Auto-Negotiation und Auto-MDI/MDI-X
- Unterstützt bis zu 1536 Bytes Paketgröße, IEEE 802.1Q VLAN Tag transparent
- VDSL2 Stand-Alone-Transceiver für einfache Bridge-Modem-Anwendung
- Vorteil der minimalen Installationszeit (einfach als Plug-and-Play)
- Wählbares Zielprofil und Ziel-SNR-Marge
- Unterstützt umfangreiche LED-Anzeigen zur Netzwerkdiagnose
- Arbeitet mit den Media Chassis der PLANET MC-Familie zusammen (MC-700 / MC-1500/ MC-1500R / MC-1500R48)
- Kompakte Größe, einfache Installation
100/100Mbps Downstream / Upstream, Hochleistungs-Ethernet über VDSL Lösung
PLANET VC-231 ist ein Ethernet-over-VDSL2-Konverter mit hoher Leistung. Er wurde auf der Grundlage von zwei zentralen Netzwerktechnologien entwickelt: Ethernet und VDSL2 (Very-high-data-rate Digital Subscriber Line 2). Die VDSL2-Technologie bietet die absolut schnellste Datenübertragungsgeschwindigkeit über bestehende Kupfertelefonleitungen, ohne dass eine Neuverkabelung erforderlich ist. Der VC-231 unterstützt Ultra-High-Performance für das flächendeckende Telefonleitungsnetz mit bis zu 100/100Mbps symmetrischer Datenrate innerhalb von 300m und 50/2Mbps für 1,4km lange Verbindungen.
Implementierung mit bestehenden Telefon-Kupferdrähten
Der VC-231 ist auch ein Long Reach Ethernet (LRE) Konverter mit einem RJ-45 Ethernet Port und einer RJ-11 Telefonbuchse, die für VDSL2 Verbindungen geeignet ist. Mit dem zusätzlichen Splitter aus dem VC-231-Paket kann der Splitter einen POTS-Splitter bereitstellen, um die vorhandene Telefonleitung mit POTS zu teilen; daher ist es nicht notwendig, die vorhandene Kupferleitung zu ersetzen. Stecken Sie den VC-231 mit zusätzlichem Splitter einfach in die vorhandene RJ-11-Telefonbuchse und schon kann ein leistungsstarkes VDSL2-Netz angeschlossen werden. Der VC-231 ist ideal als Ethernet-Extender für ein bestehendes Ethernet-Netzwerk geeignet.
Bereitstellung von anspruchsvollen Servicekonnektivität für ISP-/Triple-Play-Geräte
Der VC-231 bietet eine exzellente Bandbreite, um Triple-Play-Geräte für Home Entertainment und Kommunikation zu bedienen. Mit der Fähigkeit zur symmetrischen Datenübertragung von 100/100Mbps ermöglicht der VC-231 die Nutzung vieler Multimedia-Dienste über das lokale Internet, wie z.B. VOD (Video on Demand), Voice over IP, Videotelefonie, IPTV, Internet-Caching-Server, Fernunterricht und so weiter.
Einfache und flexible Installation
Der Ethernet-over-VDSL2-Konverter verfügt über ein Plug-and-Play-Design und ist vollständig kompatibel mit allen Arten von Netzwerkprotokollen. Darüber hinaus kann der Betriebsstatus jedes einzelnen Ports und des gesamten Systems über die zahlreichen Diagnose-LEDs an der Vorderseite überwacht werden. Der VC-231 bietet zwei Betriebsarten, CPE und CO, für die Anwendung: Der CPE-Modus wird auf der Client-Seite verwendet und der CO-Modus auf der zentralen Seite. Der CPE- oder CO-Modus kann mit Hilfe eines eingebauten DIP-Schalters eingestellt werden. Für Punkt-zu-Punkt-Verbindungen müssen ein VC-231 im CPE-Modus und ein VC-231 im CO-Modus als ein Wandlerpaar eingerichtet werden, um die Verbindung herzustellen.
Hervorragende Upstream- und Downstream-Übertragungsleistung
Der VC-231 definiert auch einen symmetrischen Bandplan für die Übertragung von Upstream- und Downstream-Signalen, der im symmetrischen Modus eine höhere Übertragungsqualität im Nahbereich für die zentrale Seite (CO) bietet. Wenn der VC-231 im Profil 17a betrieben wird, bietet er Langstreckenübertragung mit Ultra-High-Performance für das weitverzweigte Telefonnetz, und wenn der VC-231 im 30a-Betriebsmodus betrieben wird, bietet er Kurzstreckenübertragung mit Upstream- und Downstream-Übertragung mit Wire Speed Performance.

• Media conversion between 10/100/1000BASE-T and 100BASE-FX/1000BASE-SX/LX
• Copper RJ45 interface with Data + Power output
• Copper port supports 10/100/1000BASE-T auto-negotiation and auto-MDI/MDI-X.
• Fiber media allows
  
  • Multi-mode fiber using LC connector
  • Single-mode fiber using LC connector

Power over Ethernet:

• Compatible with IEEE 802.3bt Power over Ethernet plus plus end-span + mid-span PSE
• Backward Compatible with IEEE 802.3at Power over Ethernet plus end-span/mid-span PSE
• Provides DC 52V~55V power over RJ45 Ethernet cable to devices with Ethernet port
• RJ45 PoE++ port with built-in 802.3bt type-4 PoE 95W injector function
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m
• IEEE 802.3bt/IEEE 802.3at splitter devices compatibility

Layer 2 Features:

• Store-and-Forward mechanism
• Non-blocking full wire-speed forwarding rate
• IEEE 802.1Q Tag VLAN transparent, multicast pass through
• 9K jumbo frame 
• IEEE 802.3x full-duplex and half-duplex back-pressure flow control to eliminate the loss of packets 

Mechanical:

• Metal case
• LED indicators for easy network diagnostics
• DIP switch for PoE power feeding options (BT/UPOE/Legacy) selection
• DC 52V~55V power input socket
• Wall mounting or DIN-rail installation (optional)
• Compact in size, easy installation

Application:
Flexible and User-friendly PoE Deployment with Gigabit SFP Fiber Extension:
For the places difficult to find the power outlet, the GUP-805A-60W provides the easiest way to power network equipment such as PTZ (Pan, Tilt & Zoom) IP cameras, speed dome IP cameras, color touch-screen VoIP telephones, multi-channel (IEEE 802.11a/b/g/n/ac) wireless LAN access points and other network devices that need higher power to function normally. For instance, users can flexibly install security IP camera, wireless access point and other IEEE 802.3bt/at/af compliant network equipment in the public areas such as stations, freeways, airports and campuses for surveillance and wireless roaming needs. Gigabit 802.3bt PoE++ and PoE+ Network Deployment Solution:
PLANET GUP-805A-60W can easily build an 802.3BT PoE++ networking solution for the enterprises. For instance, they can work with the POS system and thin client to perform comprehensive security protection for today’s businesses. The GUP-805A-60W and 802.3bt PoE++ Splitter-POE-173S operate as a pair to provide the easiest way to power your Ethernet devices which need high power input. Receiving data and power from the GUP-805A-60W, the POE-173S separates digital data and power into three optional outputs (12V, 19V or 24V DC) to non-PoE devices such as laptops, Thin Client, POS System, PTZ (pan, tilt & zoom) network cameras, PTZ speed dome, color touch-screen IP phones, multi-channel wireless LAN access points and other network devices at distance up to 100 meters. 

• Media conversion between 10/100/1000BASE-T and 100BASE-FX/1000BASE-SX/LX
• Copper RJ45 interface with Data + Power output
• Copper port supports 10/100/1000BASE-T auto-negotiation and auto-MDI/MDI-X.
• Fiber media allows
  
  • Multi-mode fiber using LC connector
  • Single-mode fiber using LC connector

Power over Ethernet:

• Compatible with IEEE 802.3bt Power over Ethernet plus plus end-span + mid-span PSE
• Backward Compatible with IEEE 802.3at Power over Ethernet plus end-span/mid-span PSE
• Provides DC 52V~55V power over RJ45 Ethernet cable to devices with Ethernet port
• RJ45 PoE++ port with built-in 802.3bt type-4 PoE 95W injector function
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m
• IEEE 802.3bt/IEEE 802.3at splitter devices compatibility

Layer 2 Features:

• Store-and-Forward mechanism
• Non-blocking full wire-speed forwarding rate
• IEEE 802.1Q Tag VLAN transparent, multicast pass through
• 9K jumbo frame 
• IEEE 802.3x full-duplex and half-duplex back-pressure flow control to eliminate the loss of packets 

Mechanical:

• Metal case
• LED indicators for easy network diagnostics
• DIP switch for PoE power feeding options (BT/UPOE/Legacy) selection
• DC 52V~55V power input socket
• Wall mounting or DIN-rail installation (optional)
• Compact in size, easy installation

Application:
Flexible and User-friendly PoE Deployment with Gigabit SFP Fiber Extension:
For the places difficult to find the power outlet, the GUP-805A-95W provides the easiest way to power network equipment such as PTZ (Pan, Tilt & Zoom) IP cameras, speed dome IP cameras, color touch-screen VoIP telephones, multi-channel (IEEE 802.11a/b/g/n/ac) wireless LAN access points and other network devices that need higher power to function normally. For instance, users can flexibly install security IP camera, wireless access point and other IEEE 802.3bt/at/af compliant network equipment in the public areas such as stations, freeways, airports and campuses for surveillance and wireless roaming needs. Gigabit 802.3bt PoE++ and PoE+ Network Deployment Solution:
PLANET GUP-805A-95W can easily build an 802.3BT PoE++ networking solution for the enterprises. For instance, they can work with the POS system and thin client to perform comprehensive security protection for today’s businesses. The GUP-805A-95W and 802.3bt PoE++ Splitter-POE-173S operate as a pair to provide the easiest way to power your Ethernet devices which need high power input. Receiving data and power from the GUP-805A-95W, the POE-173S separates digital data and power into three optional outputs (12V, 19V or 24V DC) to non-PoE devices such as laptops, Thin Client, POS System, PTZ (pan, tilt & zoom) network cameras, PTZ speed dome, color touch-screen IP phones, multi-channel wireless LAN access points and other network devices at distance up to 100 meters. 

• Max. Leistungsaufnahme 1,5 W
• Einsparung einer halben Faser durch Verwendung von nur einer Faser zum Senden und Empfangen
• Hotplug-fähige SFP MSA-konform
• Digitale optische Überwachungsfunktion für umfangreiche Diagnosemöglichkeiten
• Konform mit IEEE 802.3z Gigabit Ethernet
• Lasersicherheitsklasse 1 und RoHS-konform

Als branchenführender Anbieter von IKT-Infrastrukturen und Industrielösungen bietet Ruijie seinen Kunden eine große Auswahl an optischen 1G-Modulen mit hoher Dichte und geringem Stromverbrauch. Sie eignen sich für Rechenzentren und Campusnetzwerke und ermöglichen kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs).  GE-SFP-LH40-SM1550-BIDI-Modul:
Das GE-SFP-LH40-SM1550-BIDI-Modul entspricht den optischen Spezifikationen von IEEE 1000BASE-LH und unterstützt eine Verbindungslänge von bis zu 40 Kilometern über ein SMF mit einem BIDI-LC-Anschluss. Er hat den SFP-Formfaktor und arbeitet mit einer Wellenlänge von 1550 nm. Der Transceiver ist konform mit IEEE 802.3, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA und RoHS-Standards.
Anwendung:
Anwendbar in Rechenzentren und Campusnetzwerken, ermöglicht kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs)

• Max. Leistungsaufnahme 1,5 W
• Einsparung einer halben Faser durch Verwendung von nur einer Faser zum Senden und Empfangen
• Hotplug-fähige SFP MSA-konform
• Digitale optische Überwachungsfunktion für umfangreiche Diagnosemöglichkeiten
• Konform mit IEEE 802.3z Gigabit Ethernet
• Lasersicherheitsklasse 1 und RoHS-konform

Als branchenführender Anbieter von IKT-Infrastrukturen und Industrielösungen bietet Ruijie seinen Kunden eine große Auswahl an optischen 1G-Modulen mit hoher Dichte und geringem Stromverbrauch. Sie eignen sich für Rechenzentren und Campusnetzwerke und ermöglichen kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs).  GE-SFP-LH40-SM1310-BIDI Module:
Das GE-SFP-LH40-SM1310-BIDI-Modul entspricht den optischen Spezifikationen von IEEE 1000BASE-LH und unterstützt eine Verbindungslänge von bis zu 40 Kilometern über ein SMF mit einem BIDI-LC-Anschluss. Er verwendet den SFP-Formfaktor und arbeitet bei einer Wellenlänge von 1310 nm. Der Transceiver ist konform mit IEEE 802.3, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA und RoHS-Standards.
Anwendung:
Anwendbar in Rechenzentren und Campusnetzwerken, ermöglicht kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs)

• Max. Leistungsaufnahme 1,5 W
• Einsparung einer halben Faser durch Verwendung von nur einer Faser zum Senden und Empfangen
• Hotplug-fähige SFP MSA-konform
• Digitale optische Überwachungsfunktion für umfangreiche Diagnosemöglichkeiten
• Konform mit IEEE 802.3z Gigabit Ethernet
• Lasersicherheitsklasse 1 und RoHS-konform

Als branchenführender Anbieter von IKT-Infrastrukturen und Industrielösungen bietet Ruijie seinen Kunden eine große Auswahl an optischen 1G-Modulen mit hoher Dichte und geringem Stromverbrauch. Sie eignen sich für Rechenzentren und Campusnetzwerke und ermöglichen kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs).  GE-SFP-LH40-SM1550-BIDI-Modul:
Das GE-SFP-LH40-SM1550-BIDI-Modul entspricht den optischen Spezifikationen von IEEE 1000BASE-LH und unterstützt eine Verbindungslänge von bis zu 40 Kilometern über ein SMF mit einem BIDI-LC-Anschluss. Er hat den SFP-Formfaktor und arbeitet mit einer Wellenlänge von 1550 nm. Der Transceiver ist konform mit IEEE 802.3, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA und RoHS-Standards.
Anwendung:
Anwendbar in Rechenzentren und Campusnetzwerken, ermöglicht kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs)

• Max. Leistungsaufnahme 1,5 W
• Einsparung einer halben Faser durch Verwendung von nur einer Faser zum Senden und Empfangen
• Hotplug-fähige SFP MSA-konform
• Digitale optische Überwachungsfunktion für umfangreiche Diagnosemöglichkeiten
• Konform mit IEEE 802.3z Gigabit Ethernet
• Lasersicherheitsklasse 1 und RoHS-konform

Als branchenführender Anbieter von IKT-Infrastrukturen und Industrielösungen bietet Ruijie seinen Kunden eine große Auswahl an optischen 1G-Modulen mit hoher Dichte und geringem Stromverbrauch. Sie eignen sich für Rechenzentren und Campusnetzwerke und ermöglichen kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs).  GE-SFP-LX20-SM1550-BIDI-Modul:
Das GE-SFP-LX20-SM1550-BIDI-Modul entspricht den optischen Spezifikationen von IEEE 1000BASE-LX und unterstützt eine Verbindungslänge von bis zu 20 Kilometern über ein SMF mit einem BIDI-LC-Anschluss. Er hat den SFP-Formfaktor und arbeitet mit einer Wellenlänge von 1550 nm. Der Transceiver ist konform mit den Standards IEEE 802.3, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA und RoHS.
Anwendung:
Anwendbar in Rechenzentren und Campusnetzwerken, ermöglicht kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs)

• One 1000Base-SX / LX SFP slot
• PCI Express x1 Host Bus interface
• 9K Jumbo Frame
• IP, TCP checksum offloading
• IEEE 802.1Q Tagged VLAN
• Low Power Consumption
• Windows XP/2003, Vista/2008, Win7, Linux, and MAC OS X Ready

  High Performance Boosts Network Traffic Speed and Flexible Distance Extension PLANET ENW-9701 1000Base-X Fiber PCI-Express Ethernet adapter is ideal for high end servers to extend long distance network reliably and flexibly with up to 2000Mbps full-duplex bandwidth capacity. It is an optimal solution for Ethernet applications by providing strictly low-power budgets and small form factor.   Flexible Distance Option With the 1000Base-SX / LX SFP (Small-Form Factor Pluggable) interface supported by the ENW-9701, the fiber network deployment distance can be extended from 550 meters (via multi-mode fiber) up to above 10/20/30/40/50/70/120 kilometers (via single-mode fiber, respectively). Users can choose the most suitable SFP transceiver module depending on their needs. The ENW-9701 connects your servers and workstations, guaranteeing extremely high throughput and excellent signal quality.   More Bandwidth and Advanced Functions The ENW-9701 is designed to address high-performance system requirements. With the innovative PCI Express Bus Architecture, the ENW-9701 provides better bandwidth and performance than the network cards which are based on 32/64bit PCI architecture. Moreover, the ENW-9701 supports IEEE 802.1Q VLAN which allows it to operate in a flexible and secure network environment. With 9K Jumbo Frame ability and IEEE 802.3 Flow Control support, it offers further optimal throughput and wire-speed packet transfer performance without risk of packet loss. The high data throughput of the device makes it ideal for most Gigabit Ethernet environments.   Seamless Integration The ENW-9701 is completely harmonious with most of the servers’ operating systems, enabling simple integration into network designs. There is no need of any modification to the server's operating system or any special software required for the ENW-9701 to be integrated into the system. The ENW-9701 can take the place of the Ethernet MAC of any conventional TCP connection and have the existing TCP/IP stack of server’s CPU still kept intact. It requires only a simple, standard PCIe driver to connect the ENW-9701 to the software.

• Max. Leistungsaufnahme 1,5 W
• Hotplug-fähige SFP MSA-konform
• Digitale optische Überwachungsfunktion für umfangreiche Diagnosemöglichkeiten
• Konform mit IEEE 802.3z Gigabit Ethernet
• Laserschutzklasse 1 und RoHS-konform

Als branchenführender Anbieter von IKT-Infrastrukturen und Industrielösungen bietet Ruijie seinen Kunden eine große Auswahl an optischen 1G-Modulen mit hoher Dichte und geringem Stromverbrauch. Sie eignen sich für Rechenzentren und Campusnetzwerke und ermöglichen kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs).  MINI-GBIC-LX-SM1310 Modul:
Das MINI-GBIC-LX-SM1310 Modul entspricht den IEEE 1000BASE-LX optischen Spezifikationen und unterstützt eine Verbindungslänge von bis zu 10 Kilometern über eine Single-Mode-Faser (SMF) mit einem LC-Stecker. Er hat den SFP-Formfaktor und arbeitet mit einer Wellenlänge von 1310 nm. Der Transceiver ist konform mit IEEE 802.3, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA und RoHS-Standards.
Anwendung:
Anwendbar in Rechenzentren und Campusnetzwerken, ermöglicht kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs)

• Max. Leistungsaufnahme 1,5 W
• Einsparung einer halben Faser durch Verwendung von nur einer Faser zum Senden und Empfangen
• Hotplug-fähige SFP MSA-konform
• Digitale optische Überwachungsfunktion für umfangreiche Diagnosemöglichkeiten
• Konform mit IEEE 802.3z Gigabit Ethernet
• Lasersicherheitsklasse 1 und RoHS-konform

Als branchenführender Anbieter von IKT-Infrastrukturen und Industrielösungen bietet Ruijie seinen Kunden eine große Auswahl an optischen 1G-Modulen mit hoher Dichte und geringem Stromverbrauch. Sie eignen sich für Rechenzentren und Campusnetzwerke und ermöglichen kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs).  MINI-GBIC-LH40-SM1310 Modul:
Das MINI-GBIC-LH40-SM1310 Modul entspricht den IEEE 1000BASE-LH optischen Spezifikationen und unterstützt eine Verbindungslänge von bis zu 40 Kilometern über ein SMF mit einem LC-Stecker. Er hat den SFP-Formfaktor und arbeitet mit einer Wellenlänge von 1310 nm. Der Transceiver ist konform mit IEEE 802.3, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA und RoHS-Standards.
Anwendung:
Anwendbar in Rechenzentren und Campusnetzwerken, ermöglicht kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs)

• Max. Leistungsaufnahme 1,5 W
• Einsparung einer halben Faser durch Verwendung von nur einer Faser zum Senden und Empfangen
• Hotplug-fähige SFP MSA-konform
• Digitale optische Überwachungsfunktion für umfangreiche Diagnosemöglichkeiten
• Konform mit IEEE 802.3z Gigabit Ethernet
• Lasersicherheitsklasse 1 und RoHS-konform

Als branchenführender Anbieter von IKT-Infrastrukturen und Industrielösungen bietet Ruijie seinen Kunden eine große Auswahl an optischen 1G-Modulen mit hoher Dichte und geringem Stromverbrauch. Sie eignen sich für Rechenzentren und Campusnetzwerke und ermöglichen kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs).  MINI-GBIC-ZX80-SM1550 Modul:
Das MINI-GBIC-ZX80-SM1550 Modul entspricht den IEEE 1000BASE-ZX optischen Spezifikationen und unterstützt eine Verbindungslänge von bis zu 80 Kilometern über ein SMF mit einem LC-Anschluss. Er hat den SFP-Formfaktor und arbeitet mit einer Wellenlänge von 1550 nm. Der Transceiver ist konform mit den Standards IEEE 802.3, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA und RoHS.
Anwendung:
Anwendbar in Rechenzentren und Campusnetzwerken, ermöglicht kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs)

• Max. Leistungsaufnahme 1,5 W
• Hotplug-fähige SFP MSA-konform
• Digitale optische Überwachungsfunktion für umfangreiche Diagnosemöglichkeiten
• Konform mit IEEE 802.3z Gigabit Ethernet
• Laserschutzklasse 1 und RoHS-konform

Als branchenführender Anbieter von IKT-Infrastrukturen und Industrielösungen bietet Ruijie seinen Kunden eine große Auswahl an optischen 1G-Modulen mit hoher Dichte und geringem Stromverbrauch. Sie eignen sich für Rechenzentren und Campusnetzwerke und ermöglichen kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs).  MINI-GBIC-SX-MM850 Modul:
Das MINI-GBIC-SX-MM850 Modul entspricht den IEEE 1000BASE-SR optischen Spezifikationen und unterstützt eine Verbindungslänge von bis zu 550 Metern über eine Multimode-Faser (MMF) mit einem LC-Stecker. Er hat den SFP-Formfaktor und arbeitet mit einer Wellenlänge von 850 nm. Der Transceiver entspricht den Standards IEEE 802.3, SFF-8472, SFF-8431, SFF-8432, SFP+ Multisource Agreement (MSA) und RoHS. 
Anwendung:
Anwendbar in Rechenzentren und Campusnetzwerken, ermöglicht kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs)

• Hochgeschwindigkeits-Datenübertragung von bis zu 1,25 Gbps
• Maximale Übertragungsdistanz von bis zu 100 Metern
• Hot-Plug-Funktion ermöglicht eine einfache Installation oder Entfernung ohne Unterbrechung des Netzwerks
• Kompatibel mit verschiedenen Netzwerkgeräten, daher vielseitig einsetzbar für unterschiedliche Konfigurationen
• Entspricht den Standards IEEE 802.3ab, SFP+ MSA und RoHS

Als branchenführender Anbieter von IKT-Infrastrukturen und Industrielösungen bietet Ruijie seinen Kunden eine große Auswahl an optischen 1G-Modulen mit hoher Dichte und geringem Stromverbrauch. Sie eignen sich für Rechenzentren und Campusnetzwerke und ermöglichen kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs).  MINI-GBIC-GT Modul:
Das MINI-GBIC-GT ist ein IEEE 1000base-X zu 1000base-T Medienkonverter und unterstützt eine Verbindungslänge von bis zu 100 Metern über ein Cat 5e/6/6a-Kabel mit einem RJ45-Anschluss. Er verwendet den SFP-Formfaktor. Der Port muss mit Auto-Negotiation konfiguriert werden. Der Transceiver entspricht den Standards IEEE 802.3ab, SFP+ MSA und RoHS.
Anwendung:
Anwendbar in Rechenzentren und Campusnetzwerken, ermöglicht kostengünstige, effiziente und schnelle Verbindungen zwischen Switches, Routern, Servern und Netzwerkschnittstellen-Controllern (NICs)

• 100-Gigabit Ethernet Verbindungen
• QSFP28-Adapter Modul für SFP28 25G/10G/1G Module

Ein kostengünstiger QSFP28 zu SFP28 Konverter, der die Verwendung von SFP28 25G/10G/1G Modulen in QSFP28 100G/40G Ports ermöglicht. Die perfekte kostengünstige und energieeffiziente Lösung zur Erweiterung Ihrer CRS504/CRS518/CRS510-Setups und zur Einsparung von Budget durch die Nutzung vorhandener Module!

• 1x 10G/5G/2.5G/1G/100BASE-T RJ45 interface with auto MDI/MDI-X function
• 1x 10GBASE-X SFP+ slot interface

  Layer 2 Features:

• IEEE 802.3u/802.3ab/802.3bz/802.3ae Ethernet standard compliant
• Supports auto-negotiation and 100Mbps half/full duplex and 1/2.5/5/10Gbps full duplex mode
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• 16K jumbo frame size support
• Automatic address learning and address aging

  Case and Installation:

• External 5V DC, 2A power supply
• DIN-rail and wall-mount design
• Supports 6000 VDC Ethernet ESD protection
• 100 meters over Cat 6A / Cat7 at 10Gbps
• 0 to 50 degrees C operating temperature
• Co-works with PLANET’s 10”/19” Media Converter Chassis (MC-700/MC-1500/MC-1500R/MC-1500R48)
• Plug and Play installation

Anwendung:
10G-SFP+-Dual-Port-Netzwerkadapter für HD-NVR-VALUE