6-port 10/100/1000BASE-T waterproof and dustproof M12 connectors with 4-port IEEE 802.3at/af Power over Ethernet Injector function   Hardware Conformance:

• Complies with IEEE 802.3at Power over Ethernet Plus end-span PSE
• Complies with IEEE 802.3af Power over Ethernet end-span PSE
• Up to 4 ports of IEEE 802.3af/802.3at devices powered
• Supports PoE Power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE Management
• Total PoE power budget controlPer port PoE function enable/disable
• PoE Port Power feeding priority- Per PoE port power limitation
• PD classification detection
• PD alive check- PoE schedule- PD scheduled power recycling

  Hardware Conformance:

• IP67-rated aluminum case
• Redundant power design
• -48 to 56V DC, redundant power with polarity reverse protect function
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilienceDIN-rail and wall-mount design
• Supports 6000V DC Ethernet ESD protection
• -40 to 75 degrees C operating temperature

  Layer 3 IP Routing Features:

• Supports maximum 32 static routes and route summarization

  Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering that eliminates erroneous packets to optimize the network bandwidth
• Storm control support
• Broadcast/Multicast/UnicastSupports VLAN
• IEEE 802.1Q tagged VLAN
• Up to 255 VLANs groups, out of 4095 VLAN Ids
• Provides Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
• Private VLAN Edge (PVE)
• Protocol-based VLAN
• MAC-based VLAN
• IP subnet-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• IEEE 802.1D Spanning Tree Protocol (STP)
• IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
• IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN- BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 3 trunk groups, with 2 ports for each trunk
• Up to 4Gbps bandwidth (full duplex mode) Provides port mirror (many-to-1)
• Port mirroring monitors the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports E.R.P.S. (Ethernet Ring Protection Switching)
• IEEE 1588 and synchronous Ethernet network timing

  Quality of Service:

• Ingress shaper and egress rate limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS- ToS/DSCP/IP precedence of IPv4/IPv6 packets
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Traffic-policing policies on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)

  Security t:

• Authentication
• IEEE 802.1x port-based/MAC-based network access authentication
• IEEE 802.1x authentication with guest VLAN
• Built-in RADIUS client to cooperate with the RADIUS servers
• RADIUS/TACACS+ users access authentication
• Access Control List
• IP-based Access Control List (ACL)
• MAC-based Access Control List (ACL)
• Source MAC/IP address binding
•  DHCP Snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
• Telnet command line interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure access
• IPv6 address/NTP management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• Firmware upload/download via HTTP/TFTP
• Reset button for system reboot or reset to factory default
• Dual images
• DHCP relay and option 82
• User privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network diagnostic
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• ICMPv6/ICMPv4 remote ping
• SMTP/Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events)
• SNMP trap for interface link up and link down notification
• System Log
• PLANET Smart Discovery Utility for deployment management

   

• 6-port 10/100/1000BASE-T waterproof and dustproof RJ45 copper
• 4-port IEEE 802.3at/af Power over Ethernet Injector function

  Hardware Conformance:

• Complies with IEEE 802.3at High Power over Ethernet end-span PSE
• Complies with IEEE 802.3af Power over Ethernet end-span PSE
• Up to 4 ports of IEEE 802.3af/802.3at devices powered
• Supports PoE Power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE Management
• Total PoE power budget control
• Per port PoE function enable/disable
• PoE Port Power feeding priority
• Per PoE port power limitation
• PD classification detection
• PD alive check
• PoE schedule
• PD scheduled power recycling

  Hardware Conformance:

• IP67-rated aluminum case
• Redundant power design
• 48 to 56V DC, redundant power with polarity reverse protect function
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience
• DIN-rail and wall-mount design
• Supports EFT protection for 6000V DC power and 6000V DC Ethernet ESD protection
• -40 to 75 degrees C operating temperature

  Layer 3 IP Routing Features:

• Supports maximum 32 static routes and route summarization

  Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering that eliminates erroneous packets to optimize the network bandwidth
• Storm control support
• Broadcast/Multicast/Unicast
• Supports VLAN
• IEEE 802.1Q tagged VLAN
• Up to 255 VLANs groups, out of 4095 VLAN Ids
• Provides Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
• Private VLAN Edge (PVE)
• Protocol-based VLAN
• MAC-based VLAN
• IP subnet-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• STP, IEEE 802.1D Spanning Tree Protocol
• RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
• MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
• BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 3 trunk groups, with 2 ports for each trunk
• Up to 4Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring monitors the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports E.R.P.S. (Ethernet Ring Protection Switching)
• IEEE 1588 and Synchronous Ethernet network timing

  Quality of Service:

• Ingress shaper and egress rate limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS
• ToS/DSCP/IP precedence of IPv4/IPv6 packets
• IP TCP/UDP port number
• Typical network applicationStrict priority and Weighted Round Robin (WRR) CoS policies
• Traffic-policing policies on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)

  Security:

• Authentication
• IEEE 802.1x port-based/MAC-based network access authentication
• IEEE 802.1x authentication with guest VLAN
• Built-in RADIUS client to cooperate with the RADIUS servers
• RADIUS/TACACS+ users access authentication
• Access Control List
• IP-based Access Control List (ACL)
• MAC-based Access Control List (ACL)
• Source MAC/IP address binding
• DHCP Snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
• Telnet command line interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure accessIPv6 address/NTP management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• Firmware upload/download via HTTP/TFTP
• Reset button for system reboot or reset to factory default
• Dual imagesDHCP relay and option 82
• User privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network diagnostic
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• ICMPv6/ICMPv4 remote pingSMTP/Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events)
• SNMP trap for interface link up and link down notification
• System Log
• PLANET Smart Discovery Utility for deployment management

   

• 6x 10/100/1000BASE-T, waterproof and dustproof M12 connectors

  Hardware Conformance:

• IP67-rated aluminum case
• Redundant power design
• 9 to 48V DC, redundant power with polarity reverse protect function
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience
• 24V AC power input acceptable
• DIN-rail and wall-mount design
• Supports Ethernet ESD protection of 6000V DC
• -40 to 75 degrees C operating temperature

  Layer 3 IP Routing Features:

• Supports maximum 32 static routes and route summarization

  Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering that eliminates erroneous packets to optimize the network bandwidth
• Storm control support
• Broadcast/Multicast/Unicast
• Supports VLAN
• IEEE 802.1Q tagged VLAN
• Up to 255 VLANs groups, out of 4095 VLAN Ids
• Provides Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
• Private VLAN Edge (PVE)- Protocol-based VLAN
• MAC-based VLAN
• IP subnet-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• IEEE 802.1D Spanning Tree Protocol (STP)
• IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
• IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
• BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 3 trunk groups, with 2 ports for each trunk
• Up to 12Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring monitors the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports ITU-T G.8032 ERPS (Ethernet Ring Protection Switching)

  Quality of Service:

• Ingress shaper and egress rate limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS- ToS/DSCP/IP precedence of IPv4/IPv6 packets
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Traffic-policing policies on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)

  Security:

• Authentication
• IEEE 802.1x port-based/MAC-based network access authentication
• IEEE 802.1x authentication with guest VLAN
• Built-in RADIUS client to cooperate with the RADIUS servers
• RADIUS/TACACS+ users access authentication
• Access Control List
• IP-based Access Control List (ACL)
• MAC-based Access Control List (ACL)
• Source MAC/IP address binding
• DHCP Snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
• Telnet command line interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure access
• IPv6 address/NTP management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• Firmware upload/download via HTTP/TFTP
• Dual imagesDHCP relay and option 82
• User privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network diagnostic
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• ICMPv6/ICMPv4 remote ping
• SMTP/Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events)
• SNMP trap for interface link up and link down notification
• System Log
• PLANET Smart Discovery Utility for deployment management

• 6x 10/100/1000BASE-T, waterproof and dustproof RJ45 copper

  Hardware Conformance:

• IP67-rated aluminum case
• Redundant power design
• 9 to 48V DC, redundant power with polarity reverse protect function
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience
• 24V AC power input acceptable
• DIN-rail and wall-mount design
• Supports Ethernet ESD protection of 6000V DC
• -40 to 75 degrees C operating temperature

  Layer 3 IP Routing Features:

• Supports maximum 32 static routes and route summarization

  Layer 2 Features

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering that eliminates erroneous packets to optimize the network bandwidth
• Storm control support
• Broadcast/Multicast/Unicast
• Supports VLAN
• IEEE 802.1Q tagged VLAN- Up to 255 VLANs groups, out of 4095 VLAN Ids
• Provides Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
• Private VLAN Edge (PVE)
•  Protocol-based VLAN
• MAC-based VLAN
• IP subnet-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• IEEE 802.1D Spanning Tree Protocol (STP)
• IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
• IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
• BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 3 trunk groups, with 2 ports for each trunk
• Up to 4Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring monitors the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports ITU-T G.8032 ERPS (Ethernet Ring Protection Switching)
• IEEE 1588 and Synchronous Ethernet network timing

  Quality of Service:

• Ingress shaper and egress rate limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS
• ToS/DSCP/IP precedence of IPv4/IPv6 packets
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Traffic-policing policies on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)

  Security:

• Authentication
• IEEE 802.1x port-based/MAC-based network access authentication
• IEEE 802.1x authentication with guest VLAN
• Built-in RADIUS client to cooperate with the RADIUS servers
• RADIUS/TACACS+ users access authentication
• Access Control List
• IP-based Access Control List (ACL)
• MAC-based Access Control List (ACL)
• Source MAC/IP address binding
• DHCP Snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
• Telnet command line interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure accessIPv6 address/NTP management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• Firmware upload/download via HTTP/TFTP
• Reset button for system reboot or reset to factory default
• Dual images
• DHCP relay and option 82
• User privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network diagnostic
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• ICMPv6/ICMPv4 remote ping
• SMTP/Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events)
• SNMP trap for interface link up and link down notification
• PLANET Smart Discovery Utility for deployment management

• 6-port 10/100/1000BASE-T waterproof and dustproof M12 X-coded female connectors with 4-port IEEE 802.3at/af Power over Ethernet Injector function 

Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus/end-span PSE
• Up to 4 IEEE 802.3af/802.3at devices powered
• Supports PoE power up to 36 watts for each PoE port (Port 3 to port 6)
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m
• PoE management features
  
  • PoE admin-mode control 
  • PoE management mode selection
  • PoE Legacy mode selection
  • PoE Budget setup option
  • Per port PoE function enable/disable
  • PoE port power feeding priority
  • Per PoE port power limit
  • PoE Port Status monitoring
  • PD classification detection
  • Sequence port PoE
• Intelligent PoE features
  
  • Temperature threshold control
  • PoE usage threshold control
  • PoE extension
  • PoE schedule
  • PD alive check
  • LLDP PoE Neighbors 

Industrial Protocol:

• Modbus TCP for real-time monitoring in the SCADA system
• IEEE 1588v2 PTP (Precision Time Protocol)  

Industrial Case and Installation:

• IP67-rated aluminum case 
• DIN-rail or wall-mount design
• 12~56V DC, redundant power with reverse polarity protection
• Supports 6KV DC Ethernet ESD protection
• -40 to 75 degrees C operating temperature  

Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
• Broadcast/Multicast/Unicast
• Supports VLAN
  
  • IEEE 802.1Q tagged VLAN
  • Up to 4K VLANs groups, out of 4094 VLAN IDs
  • Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad) 
  • Private VLAN Edge (PVE)
  • Port Isolation
  • MAC-based VLAN
  • IP Subnet-based VLAN
  • Protocol-based VLAN
  • VLAN Translation
  • Voice VLAN
  • GVRP
• Supports Spanning Tree Protocol
  
  • IEEE 802.1D Spanning Tree Protocol (STP)
  • IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
  • IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
  • BPDU Filtering/BPDU Guard
• Supports Link Aggregation
  
  • 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
  • Maximum 3 trunk groups with 2 ports per trunk group 
  • Up to 4Gbps bandwidth (duplex mode) 
• Provides port mirror (1-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port 
• Loop protection to avoid broadcast loops
• Supports ERPS (Ethernet Ring Protection Switching)
• Compatible with Cisco Uni-directional link detection (UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
• Link Layer Discovery Protocol (LLDP) 
• Provides ONVIF for co-operating with PLANET video IP surveillances

Layer 3 IP Routing Features:

• Supports maximum 8 static routes and route summarization
• IPv4/IPv6 software static routing 

Quality of Service:

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
  
  • IEEE 802.1p CoS
  • IP TOS/DSCP/IP precedence
  • IP TCP/UDP port number
  • Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking

Multicast

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD snooping v1 and v2
• Querier mode support
• IPv4 IGMP snooping port filtering
• IPv6 MLD snooping port filtering
• MVR (Multicast VLAN Registration)

Security:

• Authentication
  
  • IEEE 802.1x port-based/MAC-based network access authentication
  • Built-in RADIUS client to co-operate with the RADIUS servers
  • TACACS+ login users access authentication
  • RADIUS/TACACS+ users access authentication
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List
• Source MAC/IP address binding
• DHCP Snooping to filter un-trusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder 

Management:

• IPv4 and IPv6 dual stack management
  
  • Switch Management Interfaces
  • Web switch management
  • Telnet Command Line Interface 
  • SNMP v1 and v2c switch management
  • SSHv2, TLSv1.2 and SNMP v3 secure access
• IPv6 IP Address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via HTTP
  • Dual Images
• DHCP Relay
• DHCP Option82
• DHCP Server
• User Privilege levels control
• NTP (Network Time Protocol)
• UPnP
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• IEEE 802.3ah OAM
• Compatible with Cisco uni-directional link detection(UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
• Network Diagnostic
  
  • ICMPv6/ICMPv4 Remote Ping
  • Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues
• SMTP/Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events) 
• SNMP trap for interface Linkup and Linkdown notification
  System Log
• PLANET NMS System and Smart Discovery Utility for deployment management

• 8x 10/100Mbps M12 connector with IP67 protection

  Layer 2 Features:

• Supports auto negotiation and 10/100Mbps half / full duplex mode
• High performance Store and Forward architecture, runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (Switching Fabric): 1.6Gbps
• Integrated address look-up engine, supports 2K absolute MAC addresses
• Automatic address learning and address aging
• CSMA/CD Protocol

  Industrial Case / Installation:

• IP67 aluminum metal case protection
• DIN rail and wall mount design
• Waterproof / dustproof design
• 12 to 48V DC, redundant power with polarity reverse protect function and connective removable terminal block for master and slave power
• Supports EFT protection 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 degrees C operating temperature

• 5x 10/100/1000BASE-T Gigabit Ethernet RJ45 copper ports
• 1x SFP slot, supporting 1000BASE-X and 100BASE-FX transceiver in dual modes 

Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus, end-span PSE
• Backward compatible with IEEE 802.3af Power over Ethernet
• Up to 4 ports of IEEE 802.3af/at devices powered
• Up to 120-watt PoE budget
• Supports PoE power up to 36 watts for each PoE port
• Each port supports 54V DC power to PoE powered device
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m 

Layer 2 Switching:

• Features Store-and-Forward mode with wire-speed filtering and forwarding rates
• IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
• 4K MAC address table size
• 10K jumbo frame
• IEEE 802.1Q VLAN transparency
• Automatic address learning and address aging
• Supports CSMA/CD protocol 

Industrial Case and Installation:

• IP40 metal case
• DIN-rail, wall-mount or side wall-mount design
• 12~56V DC redundant power with reverse polarity protection
• Fault alarm for power input failed
• Supports 6KV DC Ethernet ESD protection
• -40 to 75 degrees C operating temperature 
• 4 real-time PoE power usage indicators

Cost-effective Full PoE+ Power Solution Ideal for Hardened Environment:
Featuring Plug and Play designed to be installed in heavy industrial demanding environments, the IGS-614HPT is a PLANET Industrial-grade, DIN-rail type Unmanaged Gigabit Ethernet PoE+ Switch with four 10/100/1000BASE-T ports featuring IEEE 802.3at PoE+, one extra 10/100/1000BASE-T RJ45 copper and one 100/1000BASE-X fiber optic interface for uplink connection. The IGS-614HPT is designed with redundant power system and is able to operate reliably, stably and quietly in any hardened environment without affecting its performance. It comes with a total power budget of up to 120 watts for different kinds of PoE applications and operating temperature ranging from -40 to 75 degrees C in a rugged IP40 metal housing. Convenient and Reliable Power System:
To facilitate the 802.3at PoE+ usage with commonly used 12~48V DC power input for transportation and industrial-level applications, the IGS-614HPT adopts 12~48V DC to 54V power boost technology to solve power source issue but does not require special power supplies. The IGS-614HPT provides an integrated power solution with a wide range of voltages (12~48V DC) for worldwide operability. It also provides dual-redundant, reversible polarity 12~56V DC power supply inputs for high availability applications. Fiber Optic Link Capability for Flexible Distance Extension:
The additional mini-GBIC slot built in the IGS-614HPT supports SFP auto-detection and dual speed as it features 100BASE-FX and 1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can flexibly choose the suitable SFP transceiver according to the transmission distance or the transmission speed required to extend the network efficiently. The distance can be extended from 550 meters to 2 kilometers (multi-mode fiber) and 10/20/30/40/50/60/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications to uplink to backbone switch and monitoring center in long distance. Environmentally Hardened Design:
With the IP40 metal industrial case, the IGS-614HPT provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb-side traffic control cabinets without air conditioning. It features a ventilated construction in which a cooling fan is not necessary, thereby making its operation noiseless. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-614HPT can be placed in almost any difficult environment. Robust Protection:
The IGS-614HPT provides contact discharge of ±6KV DC and air discharge of ±8KV DC for Ethernet ESD protection. It also supports ±6KV surge immunity to improve product stability and protects users’ networks from devastating ESD attacks, making sure the flow of operation does not fluctuate. Intelligent LED Indicator for Real-time PoE Usage:
The IGS-614HPT helps users to monitor current status of PoE power usage easily and efficiently by its advanced LED indication. Called “PoE Power Usage”, the front panel of the Industrial Gigabit PoE+ Switch has four orange LEDs indicating 30W, 60W, 90W and 120W of PoE power usage. Flexible and Easy Installation with Limited Space:
The compact sized IGS-614HPT is specially designed to be installed in a narrow environment, such as wall enclosure. It can be installed by fixed wall mounting or DIN rail, thereby making its usability more flexibly and easily in any space-limited location.

• 8-port 10/100/1000BASE-T RJ45 with auto MDI/MDI-X function

  Layer 2 Features

• Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet standard
• Supports auto-negotiation and 10/100Mbps half/full duplex and 1000Mbps full duplex mode
• High-performance Store and Forward architecture, broadcast storm control and runt/CRC filtering eliminate erroneous packets to optimize the network bandwidth
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• 4K absolute MAC address and 16Gbps switching fabric support
• 1.5Mbits SRAM packet buffer
• 9K jumbo packet size support
• IEEE 802.1p CoS support
• Automatic address learning and address aging
• CSMA/CD Protocol

  Industrial Case and Installation

• IP30 metal case
• DIN rail and wall-mount design
• 12 to 48V DC, redundant power with polarity reverse protect function and connective, removable terminal block for master and  

   slave power; 24V AC power support

• -40 to 75 degrees C operating temperature

    New slim type with more practicability and convenience After entering the Industrial Ethernet market with popular ISW/IFT Fast Ethernet Switch/Converter series, PLANET has released the advanced industrial hardened Gigabit Ethernet Switch series with new slim type, IP-30 metal case. The compact, IP-30 standard metal case allows either DIN rail or wall mounting for efficient use of cabinet space. The IGS-801T, one of the new models, is equipped with 8 10/100/1000Mbps auto negotiation ports and operates reliably in heavy industrial demanding environments.   Stable performance under difficult environments The IGS-801T provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-801T can be placed in almost any difficult environment. The IGS-801T also possesses an integrated power supply source with wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust Switch performance The IGS-801T offers high performance switch architecture. With the 8 10/100/1000Mbps Gigabit Ethernet ports providing non-blocking switch fabric and wire-speed throughput as high as 16Gbps and the 8K MAC Address table, the IGS-801T can perform wire-speed packets transfer without risk of packet loss.   The flow control function enables the IGS-801T to provide fast and reliable data transfer. The Gigabit port with 9K Jumbo frame supported can handle extremely large amounts of data transmission in industrial topology that forward data to central control room.   All of the RJ-45 copper interfaces in the IGS-801T support 10/100/1000Mbps auto negotiation for optimal speed detection through RJ-45 Category 6, 5 or 5e cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.

• 8-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function

  Layer 2 Features

• Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX Ethernet standard
• Supports auto-negotiation and 10/100Mbps half/full duplex mode
• High performance Store and Forward architecture; runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (switching fabric): 1.6Gbps
• Integrated address look-up engine, supporting 1K absolute MAC addresses
• Automatic address learning and address aging

  Industrial Case & Installation

• IP30-rated metal case
• DIN rail and wall-mount design
• 12 to 48V DC, redundant power with polarity reverse protection function and connective removable terminal block for master and slave power, 24V AC power support
• Lower Power Consumption device in full load operation mode
• Supports EFT protection for 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 degrees C operating temperature
• Free fall, shock-proof and vibration-proof for industries

   Slim Type with more Practicability and Convenience PLANET ISW-801T, an Industrial 8-port Fast Ethernet Switch, provides non-blocking wire-speed performance in harsh industrial environment. It also provides 8-port 10/100BASE-TX RJ45 copper interfaces delivered in an IP30 rugged, strong case with redundant power system. Its slim case is suitable for such applications as surveillance system deployments, control management and wireless service in climatically demanding environments with wide temperature range from -40 to 75 degrees C.   Energy Saving with Lower Power Consumption The ISW-801T, adopting the advanced green networking technology, provides the IEEE 802.3az protocol based power saving. This feature makes the ISW-801T consume very low power in full load operation mode, which helps conserve energy effectively but maintains high performance efficiently.   Stable Performance under Difficult Environments The ISW-801T provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb-side traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C, the ISW-801T can be placed in almost any difficult environment. The ISW-801T also possesses an integrated power supply source with wide range of voltages (12 to 48V DC, 24V AC) for worldwide high availability applications requiring dual or backup power inputs.    Robust Switch Performance Built in a high-performance switch architecture, the ISW-801T comes with eight 10/100Mbps Fast Ethernet ports providing non-blocking switch fabric and wire-speed throughput as high as 1.6Gbps, and the 1K MAC address. Thus, the ISW-801T can transfer wire-speed packets without the risk of packet loss. The flow control function enables the ISW-801T to provide fast and reliable data transfer.   All of the RJ45 copper interfaces in the ISW-801T support 10/100Mbps auto negotiation for optimal speed detection through RJ45 Category 5 or 5e cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight-through or crossover cables.

• 5-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function

  Layer 2 Features

• Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX Ethernet standard
• Supports auto-negotiation and 10/100Mbps half/full duplex mode
• High performance Store and Forward architecture; runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (switching fabric): 1Gbps
• Integrated address look-up engine, supporting 1K absolute MAC addresses
• Automatic address learning and address aging

  Industrial Case & Installation

• IP30-rated metal case
• DIN rail and wall-mount design
• 12 to 48V DC, redundant power with polarity reverse protection function and connective removable terminal block for master and slave power, 24V AC power support
• Lower Power Consumption device in full load operation mode
• Supports EFT protection for 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 degrees C operating temperature
• Free fall, shock-proof and vibration-proof for industries

  Slim Type with More Practicability and Convenience The IGS-501T advanced, slim-type, industrial, hardened Gigabit Ethernet Switch with IP30 metal case consists of 5 10/100/1000Mbps auto negotiation ports and thus, it operates reliably in heavy industrial demanding environments. Its compact IP30 standard metal case features either DIN rail or wall mount for the efficient use of cabinet space.   Stable Performance under Difficult Environments The IGS-501T provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C coupled with hazardous location certification (Class 1 Division 2), the IGS-501T can be placed in almost any difficult environment. The IGS-501T also possesses an integrated power supply source with a wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust Switch Performance The IGS-501T offers high performance switch architecture. With the 5 10/100/1000Mbps Gigabit Ethernet ports providing non-blocking switch fabric and wire-speed throughput as high as 10Gbps and the 2K MAC address table, the IGS-501T can perform wire-speed packets transfer without risk of packet loss.   The flow control function enables the IGS-501T to provide fast and reliable data transfer. The Gigabit port with 9K Jumbo frame supported can handle extremely large amounts of data transmission in industrial topology that forward data to central control room.   Plug and Play All of the RJ-45 copper interfaces in the IGS-501T support 10/100/1000Mbps auto negotiation for optimal speed detection through RJ-45 Category 6, 5 or 5e cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.

• 5-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function

  Layer 2 Features

• Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX Ethernet standard
• Supports auto-negotiation and 10/100Mbps half/full duplex mode
• High performance Store and Forward architecture; runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (switching fabric): 1Gbps
• Integrated address look-up engine, supporting 1K absolute MAC addresses
• Automatic address learning and address aging

  Industrial Case & Installation

• IP30-rated metal case
• DIN rail and wall-mount design
• 12 to 48V DC, redundant power with polarity reverse protection function and connective removable terminal block for master and slave power, 24V AC power support
• Lower Power Consumption device in full load operation mode
• Supports EFT protection for 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 degrees C operating temperature
• Free fall, shock-proof and vibration-proof for industries

  Slim type with more practicability and convenience After PLANET ISW/IFT Fast Ethernet Switch/Converter series become popular, PLANET has released the advanced industrial hardened Fast Ethernet Switch series with slim type, IP30 metal case. The compact, IP30 standard metal case allows either DIN rail or wall mounting to have the efficient use of cabinet space. The ISW-501T, one of the new models, is equipped with five 10/100Mbps auto negotiation ports and operates reliably in heavy industrial demanding environments.   Stable operating performance under difficult environments The ISW-501T provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C, the ISW-501T can be placed in almost any difficult environment. The ISW-501T also possesses an integrated power supply source with wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust switch performance The ISW-501T offers high performance switch architecture. With the five 10/100Mbps Fast Ethernet ports providing non-blocking switch fabric and wire-speed throughput as high as 1Gbps and the 2K MAC Address table, the ISW-501T can perform wire-speed packets transfer without risk of packet loss. The flow control function enables the ISW-501T to provide fast and reliable data transfer.   All of the RJ-45 copper interfaces in the ISW-501T support 10/100Mbps auto negotiation for optimal speed detection through RJ-45 Category 3, 4 or 5 cables. The standard auto-MDI / MDI-X support can detect the type of connection to any Ethernet device without requiring special-through or crossover cables.  

• 4-port 10/100Base-TX RJ-45 with auto MDI/MDI-X function
• 1-port 100Base-FX interface for up to 2km (Multi-mode fiber 50µm/125µm) on ISW-511
• 1-port 100Base-FX interface for up to 15km (Single-mode fiber 9µm/125µm) on ISW-511S15

  Layer 2 Features

• Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Ethernet standard
• Supports auto negotiation and 10/100Mbps half / full duplex mode for each copper port
• High performance Store and Forward architecture
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (Switching Fabric): 1Gbps
• Integrated address look-up engine, support 2K absolute MAC addresses
• 1 Mbit on-chip frame buffer
• Automatic address learning and address aging
• CSMA/CD Protocol

  Industrial Case / Installation

• IP-30 metal case / protection
• DIN rail and wall mount design
• 12 to 48V DC, redundant power with polarity reverse protect function and connective removable terminal block for master and slave power
• Supports EFT protection 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -10 to 60 degrees C operating temperature 

    New slim type with more practicability and convenience PLANET has released the ISW-511 / ISW-511S15, an advanced industrial hardened Ethernet Switch with new slim type, IP-30 metal case. They each are equipped with 4 10/100Base-TX auto-negotiation ports. The ISW-511 has one 100Base-FX multi-mode SC interface for transmission distance up to 2km, and the ISW-511S15 has one 100Base-FX single-mode SC interface for transmission distance up to 15km. Both of them operate reliably in Heavy Industrial demanding environments. The compact, IP-30 standard metal case allows either DIN rail or wall mounting for efficient use of cabinet space.   Stable Operating Performance under Difficult Environments The ISW-511 / ISW-511S15 provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -10 to 60 degrees C, the ISW-511 / ISW-511S15 can be placed in almost any difficult environment. The ISW-511 / ISW-511S15 also possesses an integrated power supply source with wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust Switch performance The ISW-511 / ISW-511S15 each provides four 10/100Base-TX Ethernet ports and one 100Base-FX optic-fiber SC interface, and boasts a high performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 1Gbps. With 2K MAC address table, they offer wire-speed packets transfer performance without risk of packet loss. The Flow Control function allows the ISW-511 / ISW-511S15 for fast and reliable data transfer.   All of the RJ-45 copper interfaces in the ISW-511 / ISW-511S15 support 10/100Mbps auto negotiation for optimal speed detection through RJ-45 Category 3, 4 or 5 cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.

• 4-port 10/100Base-TX RJ-45 with auto MDI/MDI-X function
• 1-port 100Base-FX interface for up to 2km (Multi-mode fiber 50µm/125µm) on ISW-511
• 1-port 100Base-FX interface for up to 15km (Single-mode fiber 9µm/125µm) on ISW-511S15

  Layer 2 Features

• Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Ethernet standard
• Supports auto negotiation and 10/100Mbps half / full duplex mode for each copper port
• High performance Store and Forward architecture
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (Switching Fabric): 1Gbps
• Integrated address look-up engine, support 2K absolute MAC addresses
• 1 Mbit on-chip frame buffer
• Automatic address learning and address aging
• CSMA/CD Protocol

  Industrial Case / Installation

• IP-30 metal case / protection
• DIN rail and wall mount design
• 12 to 48V DC, redundant power with polarity reverse protect function and connective removable terminal block for master and slave power
• Supports EFT protection 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -10 to 60 degrees C operating temperature

    New slim type with more practicability and convenience PLANET has released the ISW-511 / ISW-511S15, an advanced industrial hardened Ethernet Switch with new slim type, IP-30 metal case. They each are equipped with 4 10/100Base-TX auto-negotiation ports. The ISW-511 has one 100Base-FX multi-mode SC interface for transmission distance up to 2km, and the ISW-511S15 has one 100Base-FX single-mode SC interface for transmission distance up to 15km. Both of them operate reliably in Heavy Industrial demanding environments. The compact, IP-30 standard metal case allows either DIN rail or wall mounting for efficient use of cabinet space.   Stable Operating Performance under Difficult Environments The ISW-511 / ISW-511S15 provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -10 to 60 degrees C, the ISW-511 / ISW-511S15 can be placed in almost any difficult environment. The ISW-511 / ISW-511S15 also possesses an integrated power supply source with wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust Switch performance The ISW-511 / ISW-511S15 each provides four 10/100Base-TX Ethernet ports and one 100Base-FX optic-fiber SC interface, and boasts a high performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 1Gbps. With 2K MAC address table, they offer wire-speed packets transfer performance without risk of packet loss. The Flow Control function allows the ISW-511 / ISW-511S15 for fast and reliable data transfer.   All of the RJ-45 copper interfaces in the ISW-511 / ISW-511S15 support 10/100Mbps auto negotiation for optimal speed detection through RJ-45 Category 3, 4 or 5 cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.

• 4-port 10/100Base-TX RJ-45 with auto MDI/MDI-X function
• 2-port 100Base-FX interfaces for up to 2km (Multi-mode fiber 50µm/125µm) on ISW-621
• 2-port 100Base-FX interfaces for up to 15km (Single-mode fiber 9µm/125µm) on ISW-621S15

  Layer 2 Features

• Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Ethernet standard
• Supports auto negotiation and 10/100Mbps half / full duplex mode for each copper port
• High performance Store and Forward architecture
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (Switching Fabric): 1.2Gbps
• Integrated address look-up engine, support 2K absolute MAC addresses
• 1 Mbit on-chip frame buffer
• Automatic address learning and address aging
• CSMA/CD Protocol

  Industrial Case / Installation

• IP-30 metal case / protection
• DIN rail and wall mount design
• 12 to 48V DC, redundant power with polarity reverse protect function and
• connective removable terminal block for master and slave power
• Supports EFT protection 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -10 to 60 degrees C operating temperature  

  New slim type with more practicability and convenience PLANET has released the ISW-621/ISW-621S15, an advanced industrial hardened Ethernet Switch with new slim type, IP-30 metal case. Each of them is equipped with 4 10/100Base-TX auto-negotiation ports. The ISW-621 has 2 100Base-FX multi-mode SC interfaces for transmission distance up to 2km, and the ISW-621S15 has 2 100Base-FX single-mode SC interfaces for transmission distance up to 15km, both of them operate reliably in Heavy Industrial demanding environments. Meanwhile, the compact, IP-30 standard metal case allows either DIN rail or wall mounting for efficient use of cabinet space.   Stable operating performance under difficult environments The ISW-621 / ISW-621S15 provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -10 to 60 degrees C, the ISW-621/ISW-621S15 can be placed in almost any difficult environment. The ISW-621/ISW-621S15 also possesses an integrated power supply source with wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust Switch performance The ISW-621/ISW-621S15 each provides 4 10/100Base-TX Ethernet ports and 2 100Base-FX optic-fiber SC interfaces, and boasts a high performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 1Gbps. With 2K MAC address table, they offer wire-speed packets transfer performance without risk of packet loss. The flow control function allows the ISW-621/ISW-621S15 to have fast and reliable data transfer.   All of the RJ-45 copper interfaces in the ISW-621/ISW-621S15 support 10/100Mbps auto negotiation for optimal speed detection through RJ-45 Category 3, 4 or 5 cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.

4-port 10/100Base-TX RJ-45 with auto MDI/MDI-X function for ISW-621T series • 2-port 100Base-FX interface on ISW-621T for up to 2km (multi-mode fiber 62.5/125μm, 50/125µm) transmission distance • 2-port 100Base-FX interface on ISW-621TS15 for up to 15km (single-mode fiber 9/125µm) transmission distance   Layer 2 Features • Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Ethernet standard • Supports auto negotiation and 10/100Mbps half / full duplex mode for each copper port • High performance Store and Forward architecture • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • Backplane (Switching Fabric): 1.2Gbps • Integrated address look-up engine, supporting 2K absolute MAC addresses • 1Mbit on-chip frame buffer • Automatic address learning and address aging • CSMA/CD Protocol   Industrial Case / Installation • IP30 metal case / protection • DIN rail and wall mount design • 12 to 48V DC, redundant power with polarity reverse protection and connective removable 　terminal block for master and slave power • Supports EFT protection 6KV DC for power line • Supports 6KV DC Ethernet ESD protection • -40 to 75 degrees C wide operating temperature   Highly Convenient and Feasible Industrial Robust Switch PLANET has upgraded two models named ISW-621T and ISW-621TS15 for use in environments with wide operating temperature. The capital ‘T’ (ISW-621T and ISW-621TS15) shown in the model names means that they can support and operate under WIDE-TEMPERATURE environment ranging from -40 up to 75 degrees C. As we know the temperature in many places and countries of the world are lower than -10 degrees C, these two new models, ISW-621T and ISW-621TS15, will be the right products for Transportation, Manufacturing, Security and Surveillance network deployments in those harsh environments. The ISW-621T / ISW-621TS15 also provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets.   Flexibly Extendable Distance They(the ISW-621T and ISW-621TS15) each include four 10/100Base-TX auto-negotiation ports and two 100Base-FX ports. The ISW-621T is equipped with 100Base-FX multi-mode SC interfaces for transmission distance up to 2km while the ISW-621TS15 is equipped with 100Base-FX single-mode SC interfaces for transmission distance up to 15km. The two 100Base-FX ports provide more flexibility for Transportation, Manufacturing, Security and Surveillance with distance extension without any limitation, making the ISW-621T / ISW-621TS15 suitable either for long distance (ISW-621TS15) or short distance (ISW-621T) network deployment.   Easy Installation and Wide Range of Power Usages The ISW-621T and ISW-621TS15 are designed with a compact case that allows either DIN rail or panel mounting for the efficient usage of cabinet space. It provides an integrated power supply with a wide range of voltages for worldwide operation. It also offers dual-redundant, reversible polarity 12V DC to 48V DC power supply inputs for high availability applications requiring dual or backup power inputs.

4-port 10/100Base-TX RJ-45 with auto MDI/MDI-X function for ISW-621T series • 2-port 100Base-FX interface on ISW-621T for up to 2km (multi-mode fiber 62.5/125μm, 50/125µm) transmission distance • 2-port 100Base-FX interface on ISW-621TS15 for up to 15km (single-mode fiber 9/125µm) transmission distance   Layer 2 Features • Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Ethernet standard • Supports auto negotiation and 10/100Mbps half / full duplex mode for each copper port • High performance Store and Forward architecture • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • Backplane (Switching Fabric): 1.2Gbps • Integrated address look-up engine, supporting 2K absolute MAC addresses • 1Mbit on-chip frame buffer • Automatic address learning and address aging • CSMA/CD Protocol   Industrial Case / Installation • IP30 metal case / protection • DIN rail and wall mount design • 12 to 48V DC, redundant power with polarity reverse protection and connective removable 　terminal block for master and slave power • Supports EFT protection 6KV DC for power line • Supports 6KV DC Ethernet ESD protection • -40 to 75 degrees C wide operating temperature   Highly Convenient and Feasible Industrial Robust Switch PLANET has upgraded two models named ISW-621T and ISW-621TS15 for use in environments with wide operating temperature. The capital ‘T’ (ISW-621T and ISW-621TS15) shown in the model names means that they can support and operate under WIDE-TEMPERATURE environment ranging from -40 up to 75 degrees C. As we know the temperature in many places and countries of the world are lower than -10 degrees C, these two new models, ISW-621T and ISW-621TS15, will be the right products for Transportation, Manufacturing, Security and Surveillance network deployments in those harsh environments. The ISW-621T / ISW-621TS15 also provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets.   Flexibly Extendable Distance They(the ISW-621T and ISW-621TS15) each include four 10/100Base-TX auto-negotiation ports and two 100Base-FX ports. The ISW-621T is equipped with 100Base-FX multi-mode SC interfaces for transmission distance up to 2km while the ISW-621TS15 is equipped with 100Base-FX single-mode SC interfaces for transmission distance up to 15km. The two 100Base-FX ports provide more flexibility for Transportation, Manufacturing, Security and Surveillance with distance extension without any limitation, making the ISW-621T / ISW-621TS15 suitable either for long distance (ISW-621TS15) or short distance (ISW-621T) network deployment.   Easy Installation and Wide Range of Power Usages The ISW-621T and ISW-621TS15 are designed with a compact case that allows either DIN rail or panel mounting for the efficient usage of cabinet space. It provides an integrated power supply with a wide range of voltages for worldwide operation. It also offers dual-redundant, reversible polarity 12V DC to 48V DC power supply inputs for high availability applications requiring dual or backup power inputs.

• 4-port 10/100Base-TX RJ-45 with auto MDI / MDI-X function for ISW-511T series

• 1-port 100Base-FX interface on ISW-511T for up to 2km (multi-mode fiber 62.5/125μm, 50/125µm) transmission distance • 1-port 100Base-FX interface on ISW-511TS15 for up to 15km (single-mode fiber 9/125µm) transmission distance   Layer 2 Features • Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Ethernet standard • Supports auto negotiation and 10/100Mbps half / full duplex mode for each copper port • High performance Store and Forward architecture • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • Backplane (Switching Fabric): 1Gbps • Integrated address look-up engine, supports 2K absolute MAC addresses • 1Mbit on-chip frame buffer • Automatic address learning and address aging • CSMA / CD Protocol   Industrial Case / Installation • IP-30 metal case / protection • DIN rail and wall mount design • 12 to 48V DC, redundant power with polarity reverse protection and connective removable 　terminal block for master and slave power • Supports EFT protection 6000V DC for power line • Supports 6KV DC Ethernet ESD protection • -40 to 75 degrees C wide operating temperature  
Highly Convenient and Feasible Industrial Robust Switch PLANET has upgraded two models named ISW-511T and ISW-511TS15 for use in environments with wide operating temperature. The capital ‘T’ (ISW-511T and ISW-511TS15) shown in the model names means that they can support and operate under WIDE-TEMPERATURE environment ranging from -40 up to 75 degrees C. As we know the temperature in many places and countries of the world are lower than -10 degrees C, these two new models, ISW-511T and ISW-511TS15, will be the right products for Transportation, Manufacturing, Security and Surveillance network deployments in those harsh environments. The ISW-511T / ISW-511TS15 also provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets.   Distance Extendable and Flexibility The ISW-511T and ISW-511TS15 each includes four 10/100Base-TX auto-negotiation ports and one 100Base-FX port. The ISW-511T is equipped with 100Base-FX multi-mode SC interfaces for transmission distance up to 2km and ISW-511TS15 is equipped with 100Base-FX single-mode SC interfaces for transmission distance up to 15km. Users can choose the suitable model for network deployment either for long distance (ISW-511TS15) or short distance (ISW-511T) transmission.   Easy Installation and Wide Range of Power Usage The ISW-511T and ISW-511TS15 are designed with a compact case that allows either DIN rail or panel mounting for efficient usage of cabinet space. It provides an integrated power supply with a wide range of voltages for worldwide operation. It also offers dual-redundant, reversible polarity 12V DC to 48V DC power supply inputs for high availability applications requiring dual or backup power inputs.

• 4-port 10/100Base-TX RJ-45 with auto MDI / MDI-X function for ISW-511T series

• 1-port 100Base-FX interface on ISW-511T for up to 2km (multi-mode fiber 62.5/125μm, 50/125µm) transmission distance • 1-port 100Base-FX interface on ISW-511TS15 for up to 15km (single-mode fiber 9/125µm) transmission distance   Layer 2 Features • Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Ethernet standard • Supports auto negotiation and 10/100Mbps half / full duplex mode for each copper port • High performance Store and Forward architecture • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • Backplane (Switching Fabric): 1Gbps • Integrated address look-up engine, supports 2K absolute MAC addresses • 1Mbit on-chip frame buffer • Automatic address learning and address aging • CSMA / CD Protocol   Industrial Case / Installation • IP-30 metal case / protection • DIN rail and wall mount design • 12 to 48V DC, redundant power with polarity reverse protection and connective removable 　terminal block for master and slave power • Supports EFT protection 6000V DC for power line • Supports 6KV DC Ethernet ESD protection • -40 to 75 degrees C wide operating temperature     Highly Convenient and Feasible Industrial Robust Switch PLANET has upgraded two models named ISW-511T and ISW-511TS15 for use in environments with wide operating temperature. The capital ‘T’ (ISW-511T and ISW-511TS15) shown in the model names means that they can support and operate under WIDE-TEMPERATURE environment ranging from -40 up to 75 degrees C. As we know the temperature in many places and countries of the world are lower than -10 degrees C, these two new models, ISW-511T and ISW-511TS15, will be the right products for Transportation, Manufacturing, Security and Surveillance network deployments in those harsh environments. The ISW-511T / ISW-511TS15 also provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets.   Distance Extendable and Flexibility The ISW-511T and ISW-511TS15 each includes four 10/100Base-TX auto-negotiation ports and one 100Base-FX port. The ISW-511T is equipped with 100Base-FX multi-mode SC interfaces for transmission distance up to 2km and ISW-511TS15 is equipped with 100Base-FX single-mode SC interfaces for transmission distance up to 15km. Users can choose the suitable model for network deployment either for long distance (ISW-511TS15) or short distance (ISW-511T) transmission.   Easy Installation and Wide Range of Power Usage The ISW-511T and ISW-511TS15 are designed with a compact case that allows either DIN rail or panel mounting for efficient usage of cabinet space. It provides an integrated power supply with a wide range of voltages for worldwide operation. It also offers dual-redundant, reversible polarity 12V DC to 48V DC power supply inputs for high availability applications requiring dual or backup power inputs.

• 4-port 10/100Base-TX RJ-45 with auto MDI/MDI-X function
• 2-port 100Base-FX SFP interface

Layer 2 Features

• Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX Ethernet standard
• Supports auto negotiation and 10/100Mbps half / full duplex mode for each copper port
• High performance Store and Forward architecture
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Backplane (Switching Fabric): 1.2Gbps
• Integrated address look-up engine, supporting 2K absolute MAC addresses
• 1Mbit on-chip frame buffer
• Automatic address learning and address aging
• CSMA/CD Protocol
• Industrial Case / Installation
• IP30 metal case protection
• DIN rail and wall mount design
• 12 to 48V DC, redundant power with polarity reverse protection and connective removable terminal
• block for master and slave power
• Supports EFT protection 6KV DC for power line
• Supports 6KV DC Ethernet ESD protection
• -40 to 75 degrees C wide operating temperature 

  Highly Convenient and Distance Extendable Industrial Robust Switch PLANET ISW-621TF is a new Industrial Ethernet Switch that can operate under WIDE-TEMPERATURE environment ranging from -40 up to 75 degrees C and is equipped with two 100Base-FX SFP slots. With two mini-GBIC 100Base-FX SFP (Small-Form Factor Pluggable) interfaces supported, the deployed distance of the ISW-621TF can be extended from 2 kilometers (via multi-mode fiber) up to above 60 kilometers (via single-mode fiber), respectively. In other words, the ISW-621TF provides more flexibility for Transportation, Manufacturing, Security and Surveillance with distance extension without any limitation and is a suitable model either for long or short distance network deployment.   Hardened Design The ISW-621TF can operate stably in harsh environment with wide operating temperature support. It also provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets.   Easy Installation and Wide Range of Power Usages The ISW-621TF is designed with a compact case that allows either DIN rail or panel mounting for the efficient usage of cabinet space. It provides an integrated power supply with a wide range of voltages for worldwide operation. It also offers dual-redundant, reversible polarity 12V DC to 48V DC power supply inputs for high availability applications requiring dual or backup power inputs.

• 4x 10/100/1000BASE-T RJ45 with IEEE 802.3af / 802.3at PoE injector
• 1x 10/100/1000BASE-T RJ45 for WAN port or LAN port interface (router mode or switch mode)
• 1x USB 3.0 port for backup and restoration of configuration file 

Power over Ethernet:

• Up to 4 ports of IEEE 802.3af/802.3at devices powered
• Supports PoE power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Remote power feeding up to 100 meters
• PoE Management
  
  • PoE Port status monitoring
  • Total PoE power budget control
  • Per port PoE function enable/disable
  • PoE Port power feeding priority
  • Per PoE port power limit
  • PD classification detection
  • PoE alive check 

Industrial Case and Installation:

• Compact size with fixed wall mounting, magnetic wall mounting or DIN-rail mounting
• IP30 metal case 
• Supports -10 to 60 degrees C operating temperature 
• Supports ESD 6KV DC Ethernet protection 
  
  • Dual power input design
    48V~56V DC wide power input with polarity reverse protect function
  • 3-pin terminal block or DC jack connector 

Layer 2 Features:

• Supports IEEE 802.1Q tagged VLAN
• Supports IEEE 802.1D Spanning Tree Protocol (STP) 

 Layer 3 IP Routing Features:

• IPv6 support 
• WAN Internet types: Dynamic IP(DHCP Client), static IP, PPPoE, L2TP, PPTP
• Static and dynamic (RIP1 and 2) routing
• Supports Port Forwarding, DMZ, and UPnP for various networking applications
• IP/MAC-based bandwidth control
• Supports Dynamic DNS and PLANET DDNS 

Security;

• Port filtering lets you either allow or prevent which application can access the Internet.
• MAC filtering allows you to include or exclude computers and devices based on their MAC address
• URL filtering allows you to control access to Internet websites in an URL list
• IP source guard prevents IP spoofing attacks
• DoS attack prevention 

Management:

• Management Interfaces
  
  • 2.4-inch color LCD touch screen
  • Web GUI management
• Static and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via HTTP
  • Hardware reset button for system reboot or reset to factory default
• NTP Network Time Protocol
• Event message logging to remote syslog server
• PLANET Smart Discovery Utility for deployment management

• 8-port 10/100/1000BASE-T Gigabit RJ45 copper

  Layer 2 Features:

• High performance Store and Forward architecture
• IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
• 9K jumbo frame supported in 1000Mbps duplex mode
• Automatic address learning and address aging

  Industrial Case and Installation:

• Compact size; fixed wall mounting, magnetic wall mounting or DIN-rail mounting
• IP30 metal chassis
• Supports -10 to 60 degrees C operating temperature
• Supports ESD 4KV ESD  protection
• 12V DC input range

• 4x 10/100/1000BASE-T RJ45 with IEEE 802.3af / 802.3at PoE injector
• 1x 10/100/1000BASE-T RJ45 for WAN port or LAN port interface (router mode/switch mode)
• 1x USB 3.0 port for back up and restoration of configuration file 

Power over Ethernet:

• Up to 4 ports of IEEE 802.3af/802.3at devices powered
• Supports PoE Power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Remote power feeding up to 100 meters
• PoE Management
  
  • PoE Port status monitoring
  • Total PoE power budget control
  • Per port PoE function enable/disable
  • PoE Port power feeding priority
  • Per PoE port power limit
  • PD classification detection
  • PoE alive check 

Industrial Case and Installation:

• Compact size with fixed wall mounting, magnetic wall mounting or DIN-rail design
• IP30 metal case 
• Supports -10 to 60 degrees C operating temperature 
• Supports ESD 6KV DC Ethernet protection 
• Dual power input design
  
  • 48V~56V DC wide power input with polarity reverse protect function
  • 3-pin terminal block or DC jack connector 

Layer 2 Features:

• Supports IEEE 802.1Q tagged VLAN
• Supports IEEE 802.1D Spanning Tree Protocol (STP) 

Layer 3 IP Routing Features:

• IPv6 support 
• WAN Internet types: Dynamic IP(DHCP Client), static IP, PPPoE, L2TP, PPTP
• Static and dynamic (RIP1 and 2) routing
• Supports Port Forwarding, DMZ, UPnP and for various networking applications
• IP/MAC-based bandwidth control
• Supports Dynamic DNS and PLANET DDNS 

Security:

• Port filtering lets you either allow or prevent which applications can access the Internet.
• MAC filtering allows you to include or exclude computers and devices based on their MAC address
• URL filtering allows you to control access to Internet websites in an URL list
• IP source guard prevents IP spoofing attacks
• DoS attack prevention 

Management:

• Management Interfaces
  
  • Web GUI management
    Static and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via HTTP
  • Hardware reset button for system reboot or reset to factory default
• NTP Network Time Protocol
• Event message logging to remote syslog server
• PLANET Smart Discovery Utility for deployment management

• 8-port 10/100/1000BASE-T Gigabit RJ45 copper

  Layer 2 Features:

• High performance Store and Forward architecture
• IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
• 9K jumbo frame supported in 1000Mbps duplex mode
• Automatic address learning and address aging

  Industrial Case and Installation:

• Compact size; fixed wall mounting, magnetic wall mounting or DIN-rail mounting
• IP30 metal chassis
• Supports -10 to 60 degrees C operating temperature
• Supports ESD 4KV ESD  protection
• 12V DC input range

Industry-leading Integration of PoE Technology and Solar Power System For the increasing demand of network installation anywhere, the PLANET BSP-300 Industrial Solar Power PoE Switch now provides the ideal solution. Powered by Zero-Carbon emission source -- the sunlight, the BSP-300 incorporates Pulse Width Modulated (PWM) charge controllers to effectively force the solar panels to operate at the same voltage as the battery bank during charging. The BSP-300 can empower the high power PoE network devices anywhere without any obstacles of geographical barrier.   With the integration of the IEEE 802.3at PoE technology and solar power system, the BSP-300 provides hassle-free and maintenance-free solution for those in need for fast connectivity that requires great flexibility and reliability, such as remote monitoring and long distance wireless communication. The BSP-300 makes the network deployment easier and more reliably.   Plug and Play High Power PoE Network Deployment Through its two IEEE 802.3at Gigabit High Power PoE interface delivering power to wireless access points and IP cameras, the BSP-300 makes it easy to realize far-reaching data transmission and IP surveillance in remote areas. Just simply Plug and Play, the 802.3at / 802.3af PoE wireless LAN and IP surveillance system can be constructed easily without additional wiring.   Zero-Carbon and Stable Power Supply The BSP-300 utilizes the solar power sourcing and co-works with the common nickel-cadmium battery or lead-acid battery to form an independent solar power supply system for outdoor network system. The BSP-300 delivers zero-carbon and uninterruptible power supply for continuous outdoor wireless and IP surveillance applications without the need of any cabling. This system saves 100% power loss for users. It can power the client devices and charging at the same time during the day and continuing the operation in the night with the co-working battery.   Application Sites

• Forest / National Park Monitoring
• Public Surveillance / Public Wireless LAN System
• Telecom / ISP Wireless Extension
• Hospital / Remote Health Care
• Village / Resort
• Harbor / Oil Rig / Mine Industry
• Instant Network Infrastructure for Critical Mission

• 8x 10/100/1000BASE-T RJ45 copper ports
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-X and 2500BASE-X SFP
• One RJ45-to-RS232 console interface for basic management and setup 

Industrial Hardened Design:

• Dual power input, redundant power with reverse polarity protection
  
  • DC 12 to 48V input or AC 24V input
  • Active-active redundant power failure protection
  • Backup of catastrophic power failure on one supply
  • Fault tolerance and resilience
• DIN-rail and wall-mountable designs
• IP30 aluminum case 
• Supports 6000V DC Ethernet ESD protection
• -40 to 75 degrees C operating temperature 

Digital Input and Digital Output:

• 2 digital input (DI)
• 2 digital output (DO)
• Integrates sensors into auto alarm system
• Transfers alarm to IP network via email and SNMP trap 

Layer 3 IP Routing Features:

• IP dynamic routing protocol supports OSPFv2
• IPv4/IPv6 hardware static routing
• Routing interface provides per VLAN routing mode

Layer 2 Features:

• High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm control support
  
  • Broadcast/Multicast/Unknown unicast
• Supports VLAN
  
  • IEEE 802.1Q tagged VLAN
  • Up to 4K VLANs groups, out of 4095 VLAN IDs
  • Supports provider bridging (VLAN Q-in-Q IEEE 802.1ad)
  • Private VLAN Edge (PVE)
  • Protocol-based VLAN
  • MAC-based VLAN
  • Voice VLAN
  • GVRP (GARP VLAN Registration Protocol)
• Supports Spanning Tree Protocol
  • IEEE 802.1D Spanning Tree Protocol (STP)
  • IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
  • IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
  • BPDU Guard
• Supports Link Aggregation
  • 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
  • Maximum 14 trunk groups, with 16 ports for each trunk
  • Up to 80Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port 
• Loop protection to avoid broadcast loops
• Link Layer Discovery Protocol (LLDP)
• Compatible with Cisco uni-directional link detection(UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
• Supports G.8032 ERPS (Ethernet Ring Protection Switching)
• IEEE 1588 and Synchronous Ethernet network timing 

Quality of Service:

• Ingress shaper and egress rate limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
  
  • IEEE 802.1p CoS
  • ToS/DSCP/IP Precedence of IPv4/IPv6 packets
  • IP TCP/UDP port number
  • Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Traffic-policing  on the switch port
• DSCP remarking 
• Voice VLAN

Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD snooping v1 and v2
• Querier mode support
• IPv4 IGMP snooping port filtering
• IPv6 MLD snooping port filtering
• MVR (Multicast VLAN Registration) 

Security:

• Authentication
  
  • IEEE 802.1X Port-based/MAC-based network access authentication
  • IEEE 802.1x authentication with guest VLAN
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • RADIUS/TACACS+ users access authentication
  • Guest VLAN assigns clients to a restricted VLAN with limited services
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List (ACL)
• Source MAC/IP address binding
• DHCP Snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
  
  • Console and Telnet Command Line Interface 
  • HTTP web switch management
  • SNMP v1 and v2c switch management
  • SSH, TLS, SSL and SNMP v3 secure access
• SNMP Management
  
  • Four RMON groups (history, statistics, alarms, and events)
  • SNMP trap for interface Link Up and Link Down notification
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via HTTP
  • Reset button for system reboot or reset to factory default
  • Dual Images
• DHCP Relay
• DHCP Option 82
• DHCP Server
• User Privilege levels control
• Network Time Protocol (NTP)
• Network Diagnostic
  
  • SFP-DDM (Digital Diagnostic Monitor)
  • Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
  • ICMPv6/ICMPv4 remote ping
• SMTP/Syslog remote alarm
• System Log
• PLANET Smart Discovery Utility for deployment management

• 4x 10/100/1G/2.5GBASE-T RJ45 copper ports
• 2x 10GBASE-SR/LR SFP+ slots, compatible with 1G/2.5GBASE-X SFP
• One RJ45-to-RS232 console interface for basic management and setup

Industrial Hardened Design:

• Dual power input, redundant power with reverse polarity protection
  
  • DC 9 to 48V input or AC 24V input
  • Active-active redundant power failure protection
  • Backup of catastrophic power failure on one supply
  • Fault tolerance and resilience
• DIN-rail and wall-mountable designs
• IP30 aluminum case 
• Supports 6KV DC Ethernet ESD protection
• -40 to 75 degrees C operating temperature 

Digital Input and Digital Output:

• 2 digital input (DI)
• 2 digital output (DO)
• Integrates sensors into auto alarm system
• Transfers alarm to IP network via email and SNMP trap 

Layer 3 IP Routing Features:

• IPv4 dynamic routing protocol supports RIPv2 and OSPFv2 
• IPv6 dynamic routing protocol supports OSPFv3
• IPv4/IPv6 hardware static routing
• Routing interface provides per VLAN routing mode 

Layer 2 Features:

• High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm control support
  
  • Broadcast/Multicast/Unknown unicast
• Supports VLAN
  
  • IEEE 802.1Q tagged VLAN
  • Supports provider bridging (VLAN Q-in-Q IEEE 802.1ad) 
  • Private VLAN Edge (PVE)
  • Protocol-based VLAN
  • MAC-based VLAN
  • Voice VLAN
  • GVRP (GARP VLAN Registration Protocol)
• Supports Spanning Tree Protocol
  
  • IEEE 802.1D Spanning Tree Protocol (STP)
  • IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
  • IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
  • BPDU Guard
• Supports Link Aggregation
  
  • 802.3ad Link Aggregation Control Protocol (LACP: 6 ports/3 groups max.)
  • Cisco ether-channel (static trunk: 6 ports/3 groups max.)
• Provides port mirror (Many-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port 
• Loop protection to avoid broadcast loops
• Link Layer Discovery Protocol (LLDP)
• Compatible with Cisco uni-directional link detection(UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
• Supports G.8032 ERPS (Ethernet Ring Protection Switching)
• IEEE 1588v2 PTP (Precision Time Protocol) transparent clock mode

Quality of Service:

• Ingress shaper and egress rate limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
  
  • IEEE 802.1p CoS
  • ToS/DSCP/IP Precedence of IPv4/Ipv6 packets
  • IP TCP/UDP port number
  • Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking 
• Voice VLAN

Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD snooping v1 and v2
• Querier mode support
• IPv4 IGMP snooping port filtering
• IPv6 MLD snooping port filtering
• MVR (Multicast VLAN Registration)

 Security:

• Authentication
  
  • IEEE 802.1x port-based/MAC-based network access authentication
  • IEEE 802.1x authentication with guest VLAN
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • RADIUS/TACACS+ users access authentication
  • Guest VLAN assigns clients to a restricted VLAN with limited services
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List (ACL)
• Source MAC/IP address binding
  
  • DHCP Snooping to filter distrusted DHCP messages
  • Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
  • IP Source Guard prevents IP spoofing attacks
  • IP address access management to prevent unauthorized intruder

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
  
  • Console and Telnet Command Line Interface 
  • HTTP web switch management
  • SNMP v1 and v2c switch management
  • SSHv2, TLSv1.2 and SNMPv3 secure access
• SNMP Management
  
  • Four RMON groups (history, statistics, alarms, and events) 
  • SNMP trap for interface Link Up and Link Down notification
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via HTTP
  • Reset button for system reboot or reset to factory default
  • Dual images
• DHCP Functions:
  
  • DHCP Relay
  • DHCP Option82
  • DHCP Server
• User Privilege levels control
• Network Time Protocol (NTP)
• Network Diagnostic
  
  • SFP-DDM (Digital Diagnostic Monitor)
  • ICMPv6/ICMPv4 remote ping
• SMTP/Syslog remote alarm
• System Log
• PLANET Smart Discovery Utility for deployment management
• PLANET UNI-NMS (Universal Network Management) and CloudViewer app for deployment management

• 8x 10/100/1000BASE-T, vibration-proof and dustproof M12 X-coded female connectors 

Industrial Hardened Design:

• 1 pair of bypass protection
• IP40-rated metal case 
• Redundant power design
  
  • 9 to 48V DC, redundant power with reverse polarity protection
  • Active-active redundant power failure protection
  • Backup of catastrophic power failure on one supply
  • Fault tolerance and resilience
• DIN-rail and wall-mount designs
• Supports 6000V DC Ethernet ESD protection
• -40 to 75 degrees C operating temperature 

Industrial Protocol:

• Modbus TCP for real-time monitoring in SCADA system
• IEEE 1588v2 PTP (Precision Time Protocol) 

Layer 3 IP Routing Features:

• Supports maximum 32 static routes and route summarization 

Layer 2 Features:

• High performance of Store-and-Forward architecture, and runt/CRC filtering that eliminates erroneous packets to optimize the network bandwidth
• Storm control support
  
  • Broadcast/Multicast/Unicast
• Supports VLAN
  
  • IEEE 802.1Q tagged VLAN
  • Provides Bridging (VLAN Q-in-Q) support (IEEE 802.1ad) 
  • Private VLAN Edge (PVE)
  • Protocol-based VLAN
  • MAC-based VLAN
  • IP subnet-based VLAN
  • Voice VLAN
  • GVRP (GARP VLAN Registration Protocol)
• Supports Spanning Tree Protocol
  
  • IEEE 802.1D Spanning Tree Protocol (STP)
  • IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
  • IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
  • BPDU Guard
• Supports Link Aggregation
  
  • 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
  • Maximum 4 trunk groups, with 8 ports for each trunk 
  • Up to 16Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring monitors the incoming or outgoing traffic on a particular port 
• Loop protection to avoid broadcast loops
• Supports ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) 
• Compatible with Cisco Uni-directional link detection (UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
• Link Layer Discovery Protocol (LLDP) 

Quality of Service:

• Ingress shaper and egress rate limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
  
  • IEEE 802.1p CoS
  • ToS/DSCP/IP precedence of IPv4/IPv6 packets
  • IP TCP/UDP port number
  • Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Traffic-policing on the switch port
• DSCP remarking  

Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD snooping v1 and v2
• Querier mode support
• IPv4 IGMP snooping port filtering
• IPv6 MLD snooping port filtering
• MVR (Multicast VLAN Registration) 

Security:

• Authentication
  
  • IEEE 802.1x port-based/MAC-based network access authentication
  • IEEE 802.1x authentication with guest VLAN
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • RADIUS/TACACS+ users access authentication
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List (ACL)
• Source MAC/IP address binding
• DHCP Snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
  
  • Telnet command line interface 
  • Web switch management
  • SNMP v1, v2c, and v3 switch management
  • SSHv2 and TLSv1.2 secure access
• SNMP Management
  
  • Four RMON groups (history, statistics, alarms, and events) 
  • SNMP trap for interface Link Up and Link Down notification
• IPv6 address/NTP management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via HTTP/TFTP
  • Reset button for system reboot or reset to factory default
  • Dual images
• DHCP relay and option 82
• DHCP server
• User privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network diagnostic
  
  • Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
    ICMPv6/ICMPv4 remote ping
  • SMTP, Syslog and SNMP trap remote alarm
• System Log
• PLANET UNI-NMS (Universal Network Management) and Smart Discovery Utility for deployment management

• 8x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with IEEE 802.3at PoE+ Injector
• 2x 100/1000BASE-X mini-GBIC/SFP slots for SFP type auto detection

  Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus/end-span PSE
• Up to 8 IEEE 802.3af/802.3at devices powered
• Supports PoE power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m
• PoE management features
• Total PoE power budget control
• Per port PoE function enable/disable
• PoE admin-mode control
• PoE port power feeding priority
• Per PoE port power limit
• PD classification detection
• Intelligent PoE features
• Temperature threshold control
• PoE usage threshold control
• PD alive check
• PoE schedule

  Industrial Case and Installation:

• Compact size with fixed wall-mounted, magnetic wall-mounted or DIN-rail design
• IP30 metal case
• Supports -40 to 75 degrees C operating temperature
• Supports ESD 6KV DC Ethernet protection
• Dual power input design
• 48V~56V DC wide power input with polarity reverse protect function
• 3-pin terminal block or DC jack connector

  Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
• Broadcast/Multicast/Unicast
• Supports VLAN
• IEEE 802.1Q tagged VLAN- Up to 255 VLANs groups, out of 4094 VLAN Ids
• Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
• Private VLAN Edge (PVE)
• Protocol-based VLAN
• MAC-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• IEEE 802.1D Spanning Tree Protocol (STP)
• IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
• IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
• BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 2 trunk groups with 2 ports per trunk group
• Up to 2Gbps bandwidth (duplex mode)
• Provides port mirror (1-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports ERPS (Ethernet Ring Protection Switching)

  Layer 3 IP Routing Features:

• Supports maximum 32 static routes and route summarization

  Quality of Service:

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS
• IP TOS/DSCP/IP precedence
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)

  Security:

• IEEE 802.1x Port-based/MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers
• TACACS+ login users access authentication
• RADIUS/TACACS+ users access authentication
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Source MAC/IP address binding
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• Switch Management Interfaces
• Telnet Command Line Interface
• Web switch management
• SNMP v1 and v2c switch management
• SSH/SSL and SNMP v3 secure access
• Four RMON groups (history, statistics, alarms, and events)
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• Firmware upload/download via HTTP/TFTP
• DHCP Relay and DHCP Option 82
• User Privilege levels control
• Network Time Protocol (NTP)
• Link Layer Discovery Protocol (LLDP)
• SFP-DDM (Digital Diagnostic Monitor)
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• Reset button for system reboot or reset to factory default
• PLANET Smart Discovery Utility for deployment management

• 8x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports
• 2x 100/1000BASE-X mini-GBIC/SFP slots for SFP type auto detection

  Industrial Case and Installation:

• Compact size with fixed wall-mounted, magnetic wall-mounted or DIN-rail design
• IP30 metal case
• Supports -20 to 70 degrees C operating temperature
• Supports ESD 6KV DC Ethernet protection
• Redundant power input design
• 12V~48V DC wide power input with polarity reverse protect function
• 3-pin terminal block or DC jack connector

  Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
• Broadcast/Multicast/Unicast
• Supports VLAN
• IEEE 802.1Q tagged VLAN- Up to 255 VLANs groups, out of 4094 VLAN Ids
• Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
• Private VLAN Edge (PVE)
• Protocol-based VLAN
• MAC-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• IEEE 802.1D Spanning Tree Protocol (STP)
• IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
• IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN- BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 5 trunk groups with 2 ports per trunk group
• Up to 2Gbps bandwidth (duplex mode)
• Provides port mirror (1-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports ERPS (Ethernet Ring Protection Switching)

  Layer 3 IP Routing Features;

• Supports maximum 32 static routes and route summarization

  Quality of Service:

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS- IP TOS/DSCP/IP precedence
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)

  Security:

• IEEE 802.1x Port-based/MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers
• TACACS+ login users access authentication
• RADIUS/TACACS+ users access authentication
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Source MAC/IP address binding
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• Switch Management Interfaces
• Telnet Command Line Interface
• Web switch management
•  SNMP v1 and v2c switch management
• SSH/SSL and SNMP v3 secure access
• 2.4-inch color LCD touch screen
• Four RMON groups (history, statistics, alarms, and events)
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• Firmware upload/download via HTTP/TFTP
• DHCP Relay and DHCP Option 82
• User Privilege levels control
• Network Time Protocol (NTP)
• Link Layer Discovery Protocol (LLDP)
• SFP-DDM (Digital Diagnostic Monitor)
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• Reset button for system reboot or reset to factory default
• PLANET Smart Discovery Utility for deployment management

• 16x 10/100/1000BASE-T RJ45 with auto MDI/MDI-X function 
• 2x SFP slot interfaces, supporting 100/1000BASE-X SFP transceiver type auto detection 
• 1-port RJ45 console interface for basic management and setup 

Industrial Case and Installation:

• Dual power input, redundant power with reverse polarity protection
  
  • DC 12 to 48V input or AC 24V input
  • Active-active redundant power failure protection
  • Backup of catastrophic power failure on one supply
  • Fault tolerance and resilience
• IP30 metal case
• DIN-rail and wall-mount designs
• Supports ESD 6KV DC Ethernet protection 
• Supports -40 to 75 degrees C operating temperature
• Free fall, shock-proof and vibration-proof for industries 

Switching:

• Features Store-and-Forward mode with wire-speed filtering and forwarding rates
• IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
• 8K MAC address table size
• 10K jumbo frame
• Automatic address learning and address aging
• Supports CSMA/CD protocol 

Layer 2 Features:

• Supports VLAN
  
  • IEEE 802.1Q tagged VLAN
  • Up to 256 VLAN groups, out of 4096 VLAN IDs
  • Provider bridging (VLAN Q-in-Q, IEEE 802.1ad) support
  • Private VLAN (Protected port)
  • Protocol-based VLAN
  • Voice VLAN
  • GVRP
• Supports Spanning Tree Protocol
  
  • IEEE 802.1D Spanning Tree Protocol (STP)
  • IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
  • IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
  • BPDU Guard
• Supports Link Aggregation
  
  • IEEE 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
  • Up to 8 trunk groups
  • Up to 8 ports per trunk group with 16Gbps bandwidth
• Provides port mirror (many-to-1)
• IPv6 MAC/VLAN/Multicast Address Table
• Loop protection to avoid broadcast loops 

Quality of Service:

• Ingress/Egress Rate Limit per port bandwidth control
• Support 8 priority queues on all switch ports
• Traffic classification
  
  • IEEE 802.1p CoS
  • IP TOS/DSCP/IP precedence of IPv4/IPv6 packets
  • IP TCP/UDP port number
  • Typical network application
• DSCP remarking 

Multicast:

• Supports IPv4 IGMP snooping v1, v2, v3
• Supports IPv6 MLD snooping v1, v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering 

Security:

• Storm Control support
  
  • Broadcast/Multicast/Unicast
    Authentication
  • IEEE 802.1X port-based network access authentication
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • DHCP Relay and DHCP Option 82
  • RADIUS/TACACS+ users access authentication
• Access Control List
  
  • IPv4/IPv6 IP-based ACL
  • IPv4/IPv6 IP-based ACE
  • MAC-based ACL
  • MAC-based ACE
• MAC Security
  
  • Static MAC
  • MAC filtering
• Port security for source MAC address entries filtering
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP inspection discards ARP packets with invalid MAC address to IP address binding
• IP source guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder 

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interface
  
  • IPv4/IPv6 Web switch management
  • Console and telnet Command Line Interface
  • SNMP v1, v2c, v3
  • SSH, TLS and SSL secure access
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• Static and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via HTTP/TFTP
  • Hardware reset button for system reboot or reset to factory default
  • Dual images
• User Privilege levels control
• Network Time Protocol (NTP)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Syslog remote alarm
• SNMP Management
  
  • SNMP trap for interface link up and link down notification
  • Four RMON groups (history, statistics, alarms and events)
• PLANET Smart Discovery Utility for deployment management
• Network diagnostic
  
  • SFP-DDM (Digital Diagnostic Monitor)
  • Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
  • ICMPv6 / ICMPv4 remote pin

Cost-effective Full Solution Ideal for Hardened Environment:
Designed to be installed in heavy industrial demanding environments, the IGS-4215-16T2S is the new member of PLANET Industrial-grade, DIN-rail type L2/L4 Managed Gigabit Switch family to improve the availability of critical business applications. It provides IPv6/IPv4 dual stack management and built-in L2/L4 Gigabit switching engine along with 16 10/100/1000BASE-T ports, 2 extra 100/1000BASE-X SFP fiber slots for data and video uplink. The IGS-4215-16T2S is able to operate reliably, stably and quietly in any hardened environment without affecting its performance. It comes operating temperature ranging from -40 to 75 degrees C in a rugged IP30 metal housing. Environmentally Hardened Design:
With the IP30 industrial case, the IGS-4215-16T2S provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb-side traffic control cabinets without air conditioner. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-4215-16T2S can be placed in almost any difficult environment. Robust Protection:
The IGS-4215-16T2S provides contact discharge of ±6KV DC and air discharge of ±8KV DC for Ethernet ESD protection. It also supports ±4KV surge immunity to improve product stability and protects users’ networks from devastating ESD attacks, making sure the flow of operation does not fluctuate. Robust Layer 2 Features:
The IGS-4215-16T2S can be programmed for advanced switch management functions such as dynamic port link aggregation, 802.1Q VLAN, Q-in-Q VLAN, Multiple Spanning Tree Protocol (MSTP), loop and BPDU guard, IGMP snooping, and MLD snooping. Via the link aggregation, the IGS-4215-16T2S allows the operation of a high-speed trunk to combine with multiple ports such as an 8Gbps fat pipe, and supports fail-over as well.  Also, the Link Layer Discovery Protocol (LLDP) is the Layer 2 protocol included to help discover basic information about neighboring devices on the local broadcast domain. IPv6/IPv4 Dual Stack Management:
Supporting both IPv6 and IPv4 protocols, the IGS-4215-16T2S helps the SMBs to step in the IPv6 era with the lowest investment as its network facilities need not be replaced or overhauled if the IPv6 FTTx edge network is set up. Efficient Traffic Control:
The IGS-4215-16T2S is loaded with robust QoS features and powerful traffic management to enhance services to business-class data, voice, and video solutions. The functionality includes broadcast/multicast/unicast storm control, per port bandwidth control, 802.1p/CoS/IP DSCP QoS priority and remarking. It guarantees the best performance in VoIP and video stream transmission, and empowers the enterprises to take full advantage of the limited network resources. User-friendly and Secure Management:
The IGS-4215-16T2S comes with enhanced cybersecurity to fend off cyberthreats and cyberattacks. It supports SSHv2, TLS and SSL protocols to provide strong protection against advanced threats. Served as a key point to transmit data, the cybersecurity feature of the IGS-4215-16T2S protects the switch management and enhances the security of the mission-critical network without any extra deployment cost and effort. Powerful Security:
PLANET IGS-4215-16T2S offers comprehensive IPv4/IPv6 Layer 2 to Layer 4 Access Control List (ACL) for enforcing security to the edge. It can be used to restrict network access by denying packets based on source and destination IP address, TCP/UDP ports or defined typical network applications. Its protection mechanism also comprises 802.1X port-based user and device authentication, which can be deployed with RADIUS to ensure the port level security and block illegal users. With the Protected Port function, communication between edge ports can be prevented to guarantee user privacy. Furthermore, Port Security function allows limiting the number of network devices on a given port.  Advanced Network Security:
The IGS-4215-16T2S also provides DHCP Snooping, IP Source Guard and Dynamic ARP Inspection functions to prevent IP snooping from attack and discard ARP packets with invalid MAC address. The network administrators can now construct highly-secure corporate networks with considerably less time and effort than before. Flexibility and Long-distance Extension Solution:
The two additional SFP slots built in the IGS-4215-16T2S support 100BASE-FX /1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber transceivers to uplink to backbone switch in long distance. The distance can be extended from 550 meters to 2 kilometers (multi-mode fiber) and up to 120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions. Intelligent SFP Diagnosis Mechanism:
The IGS-4215-16T2S supports SFP-DDM (Digital Diagnostic Monitor) function that can easily monitor real-time parameters of the SFP for the network administrator, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.

• 5-Port 10/100/1000 BASE-T Gigabit RJ45 Kupfer mit 4-Port IEEE 802.3at/af PoE-Injektor (Port 1 bis Port 4)
• RJ45-Typ-Schnittstelle für Management und Setup
• USB-Typ A-Buchse für Sicherung und Wiederherstellung von Dateien

  Power over Ethernet:

• Kompatibel mit IEEE 802.3at Power-over-Ethernet-Endspan-PSE
• Rückwärtskompatibel mit IEEE 802.3af Power over Ethernet
• Bis zu 4 Ports versorgen IEEE 802.3af/802.3at-Geräten mit Strom
• Unterstützt PoE Power bis zu 30 Watt für jeden PoE Port
• Automatische Erkennung der PoE-Geräte (PD)
• Der Schaltungsschutz verhindert Stromstörungen zwischen den Ports
• Fernspeisung bis zu 100 Meter
• PoE-Verwaltung
• PoE-Gesamtbudgetkontrolle
• Pro Port PoE-Funktion aktivieren / deaktivieren
• PoE-Port-Stromversorgungspriorität
• PoE-Port-Leistungsbegrenzung
• PD Alive-Check
• PoE-Zeitplan

  Batteriemanagement:

• Batterietyp Option: Nickel-Cadmium-Batterie oder Lead-Acid-Batterie
• Einfache Diagnose des Systembetriebszustands über LED-Anzeige
• Batteriestromverbrauch und -status
• Batteriekapazität und Energieverbrauchsstatistik
• Niederspannungs-Abschaltschutz: Warnmeldung senden und den PoE-Anschluss niedriger Priorität für den Niederleistungsakku abschalten
• Pulsbreitenmodulation (PWM) Schutz
• Gegenstromschutz, um zu verhindern, dass die Stromkreise zum PV-Panel zurückfließen
• Überstrom- und Übertemperaturschutz
• Verpolungsschutz (für Batterie- und Ladeelektroden)

  Industrieller Fall u. Installation:

• IP30 Aluminiumgehäuse
• DIN-Schiene und wandmontierter Entwurf
• Unterstützt -10 bis 60 Grad C Betriebstemperatur
• Unterstützt ESD 6KV DC Ethernet-Schutz
• Redundantes Power-Design
• 24V ~ 45V DC Weitstromanschluss

  Switiching:

• Hardwarebasierte 10/100Mbps (Halb-/Vollduplex), 1000Mbps (Vollduplex), Auto-Negotiation und Auto MDI / MDI-X
• Verfügt über Store-and-Forward-Modus mit Wire-Speed-Filter- und Weiterleitungsraten
• IEEE 802.3x Flusskontrolle für Full-Duplexbetrieb und Back Pressure für Half-Duplexbetrieb
• 8K MAC-Adresstabelle Größe
• Automatisches Adresslernen und Adressaltern

  Router:

• Internet-Typen: Dynamische IP, statische IP, PPPoE, L2TP, PPTP
• Statisches und dynamisches Routing (RIP1 und 2)
• IP / MAC-basierte Bandbreitenkontrolle
• Unterstützt Port Forwarding, DMZ, UPnP und Dynamic DNS für verschiedene Netzwerkanwendungen
• 802.1d STP- und IGMP-Proxy

  Sicherheit:

• Mithilfe der Portfilterung können Sie entweder zulassen oder verhindern, welche Anwendungen auf das Internet zugreifen können.
• Mit der MAC-Filterung können Sie Computer und Geräte basierend auf ihrer MAC-Adresse ein- oder ausschließen
• Mithilfe der URL-Filterung können Sie den Zugriff auf Internetwebsites in einer URL-Liste steuern
• Der IP-Quellenschutz verhindert IP-Spoofing-Angriffe
• Schutz vor DoS-Angriffen

  Management:

• Switch-Verwaltungsschnittstelle
• IPv4-Web-Switch-Verwaltung
• SNMP v1, v2c
• Statisch und DHCP für die IP-Adresszuweisung
• Systemwartung
• Firmware Upload / Download über HTTP
• Konfiguration Upload / Download über HTTP
• Hardware-Reset-Taste für Systemneustart oder Zurücksetzen auf Werkseinstellungen
• NTP-Netzwerkzeitprotokoll
• SNMP-Trap für die Schnittstelle Link-Up- und Link-Down-Benachrichtigung
• Ereignisprotokollierung auf dem Remote-Syslog-Server
• PLANET Smart Discovery Utility

   

• 8 100/1000Base-SX/LX mini-GBIC SFP slots
• 2 10/100/1000Base-T Ethernet interface

Industrial Case / Installation

• IP30 Aluminum case protection
• DIN-Rail and Wall Mount Design
• Redundant Power Design

- 12 to 48V DC, redundant power with polarity reverse protect function - AC 24V power adapter acceptable

• Supports EFT protection 6000 VDC for power line
• Supports 6000 VDC Ethernet ESD protection
• -40 to 75 Degree C operation temperature

Layer 2 Features

• Prevents packet loss with back pressure (Half-Duplex) and IEEE 802.3x PAUSE frame flow control (Full-Duplex)
• High performance of Store-and-Forward architecture and runt/CRC filtering eliminate erroneous packets to optimize the network bandwidth
• Storm Control support

- Multicast / Unknown-Unicast

• Supports VLAN

- IEEE 802.1Q Tagged VLAN - Up to 255 VLANs groups, out of 4095 VLAN IDs - Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad) - Private VLAN - Protocol-Based VLAN - MAC-Based VLAN - Voice VLAN

• Supports Spanning Tree Protocol

- STP, IEEE 802.1D Spanning Tree Protocol - RSTP, IEEE 802.1w Rapid Spanning Tree Protocol - MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN - BPDU Guard

• Supports Link Aggregation

- 802.3ad Link Aggregation Control Protocol (LACP) - Cisco ether-channel (Static Trunk) - Maximum 5 trunk groups, up to 10 ports per trunk group - Up to 20Gbps bandwidth(Duplex Mode)

• Provides Port Mirror (many-to-1)
• Port Mirroring to monitor the incoming or outgoing traffic on a particular port
• Supports E.R.P.S. (Ethernet Ring Protection Switching, *Function to expect in future)

Quality of Service

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification

- IEEE 802.1p CoS - IP TOS / DSCP / IP Precedence - IP TCP/UDP port number - Typical network application

• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing policies on the switch port
• DSCP remarking

Multicast

• Supports IGMP Snooping v1, v2 and v3
• Supports MLD Snooping v1 and v2
• Querier mode support
• IGMP Snooping port filtering
• MLD Snooping port filtering
• MVR (Multicast VLAN Registration)

Security

• IEEE 802.1x Port-Based / MAC-Based network access authentication
• Built-in RADIUS client to co-operate with the RADIUS servers
• TACACS+ login users access authentication
• RADIUS / TACACS+ users access authentication
• IP-Based Access Control List (ACL)
• MAC-Based Access Control List
• Source MAC / IP address binding
• DHCP Snooping to filter un-trusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• Loop Protection
• IP address access management to prevent unauthorized intruder

Management

• Switch /Management Interfaces

- Web switch management - Remote Telnet management - SNMP v1, v2c, and v3 switch management - SSH / SSL secure access

• Four RMON groups (history, statistics, alarms, and events)
• IPv6 IP Address / NTP / DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• Firmware upload/download via HTTP / TFTP
• DHCP Relay
• DHCP Option82
• User Privilege levels control
• NTP (Network Time Protocol)
• PTP (Precision Time Protocol)
• Link Layer Discovery Protocol (LLDP) Protocol
• Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues
• Reset button for system reboot or reset to factory default
• PLANET Smart Discovery Utility for deploy management

  Multiple SFP Fiber Port Switch for Growing Long-Reach Networking of Industry and Telecom PLANET IGS-10080MFT is an Industrial 10-Port Full Gigabit Managed Ethernet Switch specially designed to build a full Gigabit backbone to transmit reliable, high speed data in heavy industrial demanding environments and also can forward data to remote network through fiber optic. It provides 8-Port 100/1000Base-X SFP fiber optic interface and 2 extra 10/100/1000Base-T copper interfaces delivered in an IP30 rugged strong case with redundant power system, being able to operate under the temperature range from -40 to 75 Degree C, the IGS-10080MFT can be placed in almost any difficult environment.    IPv6 / IPv4 Full-Functioned Managed Switch for Building Automation Networking The IGS-10080MFT is the ideal solution to fulfill the demand of IPv6 management Gigabit Ethernet Switch, especially in the Industrial hardened environment. It supports both IPv4 and IPv6 management functions and can work with original network structure. The IGS-10080MFT provides advanced Layer 2 to Layer 4 data switching and redundancy, Quality of Service traffic control, network access control and authentication, and Secure Management features to protect customer’s industrial and automation network connectivity.   Fast Recovery to a Redundant Ethernet Network The IGS-10080MFT features strong and self-recovery capability to prevent interruptions and outside intrusions. It incorporates Rapid Spanning Protocol (RSTP), Multiple Spanning Tree (MSTP) as well as the Loop protection function that will shutdown specific Ethernet interfaces when system detects a loop. The dynamic port Link Aggregation and Redundant Power System are provided into customers’ industrial automation network to enhance system reliability and uptime in the harsh factory environments. It greatly protects customer’s industrial network with switching recovery capability that is used for implementing fault tolerant ring architectures.   Flexible and Extendable Solution The 8 mini-GBIC slots built in the IGS-10080MFT support Dual-Speed, 100Base-FX and 1000Base-SX/LX SFP (Small Form-factor Pluggable) fiber-optic modules, that means, the administrator now can flexibly choose the suitable SFP transceiver according to the transmission distance or the transmission speed required to extend the network efficiently.