• Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u, 100BASE-TX and 100BASE-FX Ethernet standards
• One 10/100BASE-TX port with RJ45 connector
• One 100BASE-FX port with ST/SC/WDM connector supporting multi-mode or single-mode fiber optic cable
• Auto-negotiation and auto-MDI / MDI-X for 10/100BASE-TX port
• Back-pressure and IEEE 802.3x compliant flow control and full wire-speed forwarding rate
• Link Loss Return (LLR) switch on each fiber optic is to aid in troubleshooting remote network connections
• Link Loss Carry Forward (LLCF) works with LLR in diagnosing network connections

  Distance Extended with Fiber Optic Cable PLANET FST-80x Smart Media Converter series provides media conversion between 10/100BASE-TX and 100BASE-FX interfaces, such as multi-mode ST/SC connectors (2km), single-mode SC connector (15/35/50km) and single fiber connector using the wavelength-division multiplexing (WDM) technology (20/60km) to enable to extend links over long distances using fiber optic cable.    Enhanced Smart Management Features The FST-80x series provides auto MDI/MDI-X on their TP port and store-and-forward mechanism to eliminate faulty packets. Use the DIP switch from the FST-80x to configure the available smart functions, such as the half/full duplex, auto-negotiation / force and 10/100Mbps options for TP and fiber interfaces. Besides, the Link Loss Return (LLR) and Link Loss Carry Forward (LLCF) functions can immediately alarm network administrator once there is a media link issue, thus helping to monitor the status of the entire network.    Easy Installation The FST-80x series can be connected easily and cost-effectively as these smart media converters can be used as a standalone unit when powered on by its DC adapter, or used as a slide-in module connected to PLANET 19-inch, 16-slot web smart/managed media converter chassis (MC-1600MR/MC-1600MR48 and MC-1610MR/MC-1610MR48). When working with the web smart/managed media converter chassis, the status of the FST-80x can be monitored via the local RS-232 console and remote web interface.

• Complies with IEEE 802.3, IEEE 802.3u 10 / 100Base-TX and 100Base-FX
• IEEE 802.3x full-duplex flow-control, back-pressure in Half-duplex eliminate packet loss
• TS-1000 / OAM function built-in, the device can be remotely monitored with port link status
• Dual 100Base-FX SFP fiber optic
• One 10 / 100Base-TX copper
• Auto-negotiation for 100Base-TX half-duplex or 100Base-T full-duplex
• Supports auto MDI / MDI-X function
• Supports maximum frame size up to 2046Kbytes
• Link status auto-detect and redundant on dual ports with the same connector type
• Only primary port is active at a time, the backup port is blocked
• While primary port link fail occurrences, the traffic will swap to backup port automatically
• Once the primary port status is back to linkup, the traffic will swap from backup port to primary port
• Hardware redundant swaps less than 10 ms

  PLANET FT-1205A is a 3-port Redundant Media Converter which supports conversion between 10 / 100Base-TX and 100Base-FX network. The difference with the other one-port channel media converter is the Redundant Media Converter. It is designed for critical networks that require fibers or copper links to automatically recover less than 10ms, such as ISPs, telecoms, hospitals, banks and enterprises.   Via the built-in DIP switches, the converter can be configured as 3-port Ethernet switch or 2-port redundant media converter. With the 3-port switch mode, it can operate Store-and-Forward mechanism with high performance, and it can also prevent packet loss via IEEE 802.3x flow control (full-duplex) and back pressure (half-duplex).   With the 2-port redundant mode, it provides less than 10ms redundancy of link for highly critical Ethernet applications. The redundant mode supports auto-recover function. If the destination port of a packet is link-down, it forwards the packet to the other port of the backup pair.   The SFP slot supports single-mode, multi-mode and WDM small-form factory type transceiver modules for various applications. The FT-1205A is with high reliability and flexibility to extend the distance up to 2km, 20km or longer. It depends on the 100Base-FX SFP transceiver modules. The Ethernet signal that allows two types of segments to connect easily, efficiently and inexpensively.   The converters can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter Chassis, MC-700, MC-1500, MC-1500R and MC-1500R48. As to the other PLANET media converters (FT series), they're hot swappable in MC chassis.

• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard • Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568 • One fiber-optic, 1310nm wavelength, connector type and distance vary with model    - FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm    - FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm • Data Transfer Rate:   - TP: 10/100Mbps     - FX: 100Mbps • Duplex mode support:  - Full or half-duplex mode by auto-negotiation (TP)   - Full or half-duplex mode by DIP switch (FX) • LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL • DIP switch: 2 DIP switches   - Rear DIP switch: FX duplex mode selection   - Side DIP switch: LFP (Link Fault Pass-through) mode selection • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets     PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard • Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568 • One fiber-optic, 1310nm wavelength, connector type and distance vary with model    - FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm    - FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm • Data Transfer Rate:   - TP: 10/100Mbps     - FX: 100Mbps • Duplex mode support:  - Full or half-duplex mode by auto-negotiation (TP)   - Full or half-duplex mode by DIP switch (FX) • LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL • DIP switch: 2 DIP switches   - Rear DIP switch: FX duplex mode selection   - Side DIP switch: LFP (Link Fault Pass-through) mode selection • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets     PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-SX/LX. • TP port supports 10/100/1000Base-T auto-negotiation and auto-MDI/MDI-X. • 1000Base-SX: 50/125μm or 62.5/125μm multi-mode fiber cable, up to 220/550m (GT-802). • 1000Base-LX: 9/125μm single-mode cable provides long distance for 10km (GT-802S). • 1000Base-LX WDM interface for up to 15km (single-mode fiber 9μm/125μm) on GT-806A15/B15. • 1000Base-LX WDM interface for up to 60km (single-mode fiber 9μm/125μm) on GT-806A60/B60. • 1000Base-T: 2-pair Cat. 5/5e/6 UTP cable, up to 100 meters. • Layer 2 key Feature 　–IEEE 802.3x full-duplex flow-control and back-pressure in half-duplex eliminate the loss of packets 　–Supports auto MDI/MDI-X function 　–Store-and-Forward mechanism 　–Non-blocking full wire-speed forwarding rate • Media conversion between 10/100/1000Base-T and 1000Base-SX/LX. • Fiber media allows: 　–Multi-mode fiber using SC/LC/WDM connector; 　–Single-mode fiber using SC/LC/WDM connector • Compact size for working with PLANET MC family media chassis (MC-700 / MC-1500 / MC-1500R / MC-1500R48) • Wall-mountable design • LED indicators for easy network diagnostics • Provides DIP switch for LFP function (Disable / Enable) setting • OAM TS-1000 supported • 9K Jumbo Frame Supported • Choice of fiber-connector from SC, LC and WDM, multi-mode / single-mode fiber for 1000Base 　SFP interface • Compact in size, easy installation   Providing the flexibility of 10/100/1000Mbps Ethernet Media via RJ-45 port and highly stable Gigabit fiber performance, PLANET GT-802, GT-802S, GT-805A and GT-806A/B media converters support conversion between 10/100/1000Base-T and 1000Base-LX/SX network. There are SC/SFP/WDM connectors with single-mode or multi-mode media as required. The Ethernet signal allows three types of segments to connect easily, efficiently and inexpensively.   Distance Extension with High Performance and Steady Network Communications PLANET GT-80x gigabit media converter series extends communications distance with highly Gigabit performance via fiber optic cable. The GT-80x series provides media conversion between 10/100/1000Base-T and 1000Base-SX/LX interfaces such as multi-mode LC/SC connectors (220m / 550m), single-mode LC/SC connectors (10/20/30/40/50/70/120km) and single fiber connectors (WDM, 15/60km) for various fiber optic applications.   Enhanced Smart Management Features The GT-80x series provides auto MDI/MDI-X on its TP port and the DIP switch to configure the Link Fault Pass through function (LFP). The LFP function includes the Link Loss Carry Forward (LLCF)/Link Loss Return (LLR). LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch can disable or enable the LFP function. The LLCF means when a device connected to the converter and the TP line loses the link, the converter’s fiber will disconnect the link of transmission. The LLR (Link Loss Return) means when a device connected to the converter and the fiber line loses the link, the converter’s fiber will disconnect the link of transmission. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.   Moreover, Even the web UI is not available on GT-80x, the network manager still can remotely control and monitor GT-80X by OAM TS-1000 terminal function such as remote failure indication, loop back test, port status, performance monitoring and troubleshooting. PLANET GT-90x and IGT-90xT models provide TS-1000/802.3ah OAM protocol (operations, administration, and maintenance) that helps the remote GT-80x device to manage and monitor.   Easy Installation The GT-80x series allows two types of the segment to connect easily. The GT-80x series can be used as a standalone unit when powered by its DC adapter or used as a slide-in module to PLANET 19-inch 7-/15-slot media converter chassis (MC-700/MC-1500/ MC-1500R / MC-1500R48). These media chassis can assist in producing the power for the GT-80x to maintain the fiber-optic network at one location. As the Gigabit Media Converter fully complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T and IEEE 802.3z 1000Base-LX/SX, the Gigabit media conversion installation is quite quick and easy with its plug and play feature. The GT-80x also supports flow control and back pressure in half-duplex to eliminate packet loss.

• Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-SX/LX. • TP port supports 10/100/1000Base-T auto-negotiation and auto-MDI/MDI-X. • 1000Base-SX: 50/125μm or 62.5/125μm multi-mode fiber cable, up to 220/550m (GT-802). • 1000Base-LX: 9/125μm single-mode cable provides long distance for 10km (GT-802S). • 1000Base-LX WDM interface for up to 15km (single-mode fiber 9μm/125μm) on GT-806A15/B15. • 1000Base-LX WDM interface for up to 60km (single-mode fiber 9μm/125μm) on GT-806A60/B60. • 1000Base-T: 2-pair Cat. 5/5e/6 UTP cable, up to 100 meters. Layer 2 key Feature –IEEE 802.3x full-duplex flow-control and back-pressure in half-duplex eliminate the loss of packets –Supports auto MDI/MDI-X function –Store-and-Forward mechanism –Non-blocking full wire-speed forwarding rate • Media conversion between 10/100/1000Base-T and 1000Base-SX/LX. • Fiber media allows: –Multi-mode fiber using SC/LC/WDM connector; –Single-mode fiber using SC/LC/WDM connector • Compact size for working with PLANET MC family media chassis (MC-700 / MC-1500 / MC-1500R / MC-1500R48) • Wall-mountable design • LED indicators for easy network diagnostics • Provides DIP switch for LFP function (Disable / Enable) setting • OAM TS-1000 supported • 9K Jumbo Frame Supported • Choice of fiber-connector from SC, LC and WDM, multi-mode / single-mode fiber for 1000Base    SFP interface • Compact in size, easy installation   Providing the flexibility of 10/100/1000Mbps Ethernet Media via RJ-45 port and highly stable Gigabit fiber performance, PLANET GT-802, GT-802S, GT-805A and GT-806A/B media converters support conversion between 10/100/1000Base-T and 1000Base-LX/SX network. There are SC/SFP/WDM connectors with single-mode or multi-mode media as required. The Ethernet signal allows three types of segments to connect easily, efficiently and inexpensively.   Distance Extension with High Performance and Steady Network Communications PLANET GT-80x gigabit media converter series extends communications distance with highly Gigabit performance via fiber optic cable. The GT-80x series provides media conversion between 10/100/1000Base-T and 1000Base-SX/LX interfaces such as multi-mode LC/SC connectors (220m / 550m), single-mode LC/SC connectors (10/20/30/40/50/70/120km) and single fiber connectors (WDM, 15/60km) for various fiber optic applications.   Enhanced Smart Management Features The GT-80x series provides auto MDI/MDI-X on its TP port and the DIP switch to configure the Link Fault Pass through function (LFP). The LFP function includes the Link Loss Carry Forward (LLCF)/Link Loss Return (LLR). LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch can disable or enable the LFP function. The LLCF means when a device connected to the converter and the TP line loses the link, the converter’s fiber will disconnect the link of transmission. The LLR (Link Loss Return) means when a device connected to the converter and the fiber line loses the link, the converter’s fiber will disconnect the link of transmission. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.   Moreover, Even the web UI is not available on GT-80x, the network manager still can remotely control and monitor GT-80X by OAM TS-1000 terminal function such as remote failure indication, loop back test, port status, performance monitoring and troubleshooting. PLANET GT-90x and IGT-90xT models provide TS-1000/802.3ah OAM protocol (operations, administration, and maintenance) that helps the remote GT-80x device to manage and monitor.   Easy Installation The GT-80x series allows two types of the segment to connect easily. The GT-80x series can be used as a standalone unit when powered by its DC adapter or used as a slide-in module to PLANET 19-inch 7-/15-slot media converter chassis (MC-700/MC-1500/ MC-1500R / MC-1500R48). These media chassis can assist in producing the power for the GT-80x to maintain the fiber-optic network at one location. As the Gigabit Media Converter fully complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T and IEEE 802.3z 1000Base-LX/SX, the Gigabit media conversion installation is quite quick and easy with its plug and play feature. The GT-80x also supports flow control and back pressure in half-duplex to eliminate packet loss.

• Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-SX/LX • One-channel media conversion between 10/100/1000Base-T and 1000Base-SX / LX • TP port supports 10/100/1000Base-T auto-negotiation and auto-MDI/MDI-X • 1000Base-SX: 50/125μm or 62.5/125μm multi-mode fiber cable, up to 220/550m on GT-902 • 1000Base-LX: 9/125μm single-mode cable provides long distance for 10km on GT-902S • 1000Base-LX WDM interface for up to 15km (single-mode fiber 9μm/125μm) on GT-906A15/B15 • 1000Base-LX WDM interface for up to 60km (single-mode fiber 9μm/125μm) on GT-906A60/B60 • 1000Base-T: 2-pair Cat. 5/5e/6 UTP cable, up to 100 meters • Compact size for working with PLANET MC family Media Chassis (MC-700/1000R/1500) • Wall-mountable hardware design • Built-in IP-based Web interface for remote management • Layer 2 Management Feature 　–Store-and-Forward mechanism 　–Built-in Web interface for remote management and setup 　–Manual IP address setting / DHCP client for IP address assignment 　–SNMP v1 / v2c monitor / private Enterprise MIB 　–Event trap and SNMP trap support 　–Speed duplex mode configuration / Flow Control setting / bandwidth Control on TP / Fiber port 　–Supports Port Status / Ethernet Statistics on both TP and Fiber interface 　–Supports Maximum frame size to 16K bytes 　–Loop detection / Broadcast / Multicast / Unicast storm control 　–Management VLAN / 16 IEEE 802.1Q VLAN groups / Q-in-Q VLAN 　–802.1p Tag Priority / IP address priority / IP DSCP option in Quality of Service Mode and Strict Priority / Weighted Round Robin (WRR) QoS policies 　–TS-1000 OAM / IEEE 802.3ah OAM / Loop Back Test 　–16 TCP / UDP Filter groups 　–Password setting, IP setting and devices description setting through Planet Smart discovery utility 　–Firmware upgrade via remote Web interface • External DC 5V 2A power supply • LED indicators for easy network diagnosing • Reset Button at the front panel for the factory default reset • Choice of fiber-connector from SC, LC, WDM, multi-mode / single-mode fiber /1000Base-SX / LX mini GBIC module   WEB/SNMP/OAM Remotely Managed Gigabit Converter PLANET GT-90x series is a 10/100/1000Base-T to 1000Base-LX / SX Managed Media Converter developed to meet the advanced demand for further Network applications and equipped with the feature of plug and play. The GT-90x series provides all kinds of 10/100/1000Mbps Ethernet Media on RJ-45 port and offers highly stable Gigabit fiber performance. It supports conversion between 10/100/1000Base-T and 1000Base-LX / SX network, which includes SC / SFP / WDM connectors with single-mode or multi-mode media as required. The Ethernet signal allows three types of segments to connect easily, efficiently and inexpensively.   Friendly/Centralized/Simple Web Management Interface For efficient management, the GT-90x Managed Gigabit Ethernet Media Converter series is equipped with remote Web / SNMP interface. With its built-in Web-based management, PLANET GT-90x series acts as an easy-to-use, platform-independent management and configuration facility. The GT-90x series also supports standard Simple Network Management Protocol (SNMP) and can be managed via any standard-based management software. Moreover, the TS-1000/802.3ah OAM protocol (operations, administration, and maintenance) supported helps remote device be managed and monitored by the GT-90x.   Enhanced Management Features The GT-90x series can be programmed for advanced management functions such as IP address configuration, DHCP Client function, port configuration, converter configuration, 802.1Q Tag VLAN, Q-in-Q VLAN, Ingress/Egress bandwidth control, QoS and Layer protocol filter, broadcast storm and bandwidth control, to enhance bandwidth utilization.   Easy Installation As the GT-90x Managed Gigabit Ethernet Media Converter series fully complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T and IEEE 802.3z 1000Base-LX / SX, the Gigabit media conversion installation is quite quick and easy simply by utilizing plug and play feature. This GT-90x series can be used as a stand-alone unit or as a slide-in module to PLANET Media Converter Chassis (MC-700, MC-1000 and MC-1500). The media converter chassis can provide DC power to GT-90x series to maintain the fiber-optic network at the central location.

• Power Requirements: 100-240V AC
• Power Consumption: 130 Watts

  The MC-RPS130 is a 100-240VAC 130W Redundant Power Supply for Planet Technology models MC-1610MR and MC-1610MR48.