• 24x Gigabit-PoE-Ports
• 2x Gigabit-Glasfaser-Ports.
• IEEE 802.3at/af-Standard für PoE-Ports.
• Management der Netzwerktopologie, Alarm-Push, Netzwerkzustandsüberwachung.
• 6-KV-Überspannungsschutz für PoE-Ports.
• Die AF/AT-Kamera kann im Extended-Mode bis zu 300 m erreichen.
• PoE-Watchdog, um die Kameras, die nicht reagieren, automatisch zu erkennen und neu zu starten.
• Verschiedene Layer-2-Verwaltungsprotokolle wie STP/RSTP, VLAN, Link Aggregation, SNMP, QoS usw.

• 24x 10/100/1000BASE-T Gigabit RJ45 copper ports with 24-port IEEE 802.3bt PoE++ injector function
• 2x 10GBASE-T RJ45 interfaces with auto MDI/MDI-X function
• 2x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 console interface for switch basic management and setup 

802.3bt Power over Ethernet:

• Complies with IEEE 802.3bt Power over Ethernet Plus Plus
• Backward compatible with IEEE 802.3af /at Power over Ethernet
• Up to 24 ports of IEEE 802.3af/IEEE 802.3at/IEEE 802.3bt PoE devices powered
• 8 PoE ports with built-in 802.3bt PoE++ Type-4 90W injector function (Port-1 to Port-8)
• 16 PoE ports with built-in 802.3bt PoE++ Type-3 60W injector function (Port-9 to Port-24)
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE management
  
  • Total PoE power budget control
  • Per port PoE function enable/disable
  • PoE admin-mode control
  • PoE port power feeding priority
  • Per PoE port power limitation
  • PD classification detection
  • Temperature threshold control
  • PD alive check
  • PoE schedule

Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
  
  • Broadcast/Multicast/Unknown unicast
    Supports VLAN
  • IEEE 802.1Q tagged VLAN
  • Up to 255 VLANs groups, out of 4094 VLAN IDs
  • Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad)
  • Private VLAN Edge (PVE)
  • Protocol-based VLAN
  • MAC-based VLAN
  • Voice VLAN
  • GVRP (GARP VLAN Registration Protocol)
• Supports Spanning Tree Protocol
  
  • IEEE 802.1D Spanning Tree Protocol (STP)
  • IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
  • IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
  • BPDU Guard
• Supports Link Aggregation
  
  • 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
  • Maximum 26 trunk groups with 4 ports for each trunk group 
  • Up to 80Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports ERPS (Ethernet Ring Protection Switching)
• Compatible with Cisco uni-directional link detection(UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
• Link Layer Discovery Protocol (LLDP)

Layer 3 Features:

• IP dynamic routing protocol supports OSPFv2
• IPv4/IPv6 hardware static routing
• Routing interface provides per VLAN routing mode
• IP interfaces (Max. 128 VLAN interfaces)
• Routing table (Max. 128 routing entries)

Quality of Service:

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
  
  • IEEE 802.1p CoS
  • TOS/DSCP/IP precedence of IPv4/IPv6 packets
  • IP TCP/UDP port number
  • Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking

Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD snooping v1 and v2
• Querier mode support
• IPv4 IGMP snooping port filtering
• IPv6 MLD snooping port filtering
• Multicast VLAN Registration (MVR) support

Security:

• Authentication
  
  • IEEE 802.1x port-based/MAC-based network access authentication
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • TACACS+ login users access authentication
  • RADIUS/TACACS+ users access authentication
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List
• Source MAC/IP address binding
• DHCP Snooping to filter untrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
  
  • Console/Telnet Command Line Interface
  • Web switch management
  • SNMP v1, v2c, and v3 switch management
  • SSH, TLS, SSL and SNMP v3 secure access

• SNMP Management
  
  • Four RMON groups (history, statistics, alarms and events)
  • SNMP trap for interface Link Up and Link Down notification
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
  System Maintenance
  
  • Firmware upload/download via HTTP/TFTP
  • Reset button for system reboot or reset to factory default
  • Dual images
• DHCP Relay and DHCP Option 82
• DHCP Server
• User Privilege levels control
• NTP (Network Time Protocol)
• Network Diagnostic
  
  • ICMPv6/ICMPv4 remote ping
  • Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• SMTP/Syslog remote alarm
• System Log
• PLANET Smart Discovery Utility for deployment management
• Smart fan with speed control

Redundant Power System:

• Redundant 100~240V AC/36-60V DC dual power 
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience

• 24x 10/100/1000BASE-T Gigabit RJ45 copper ports with 24-port IEEE 802.3bt PoE++ injector function
• 2x 10GBASE-T RJ45 interfaces with auto MDI/MDI-X function
• 2x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP and 2.5G SFP transceiver
• RJ45 console interface for switch basic management and setup   

802.3bt Power over Ethernet:

• Complies with IEEE 802.3bt Power over Ethernet Plus Plus
• Backward compatible with IEEE 802.3at Power over Ethernet Plus
• Up to 24 ports of IEEE 802.3af/IEEE 802.3at/IEEE 802.3bt PoE devices powered
• 24 PoE ports with built-in 802.3bt PoE++ Type-4 90W injector function
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE management features
  
  • Total PoE power budget control
  • Per port PoE function enable/disable
  • PoE admin-mode control 
  • PoE port power feeding priority
  • Per PoE port power limit
  • PD classification detection
  • PoE extend mode control to support power feeding up to a distance of up to 200 meters
• Intelligent PoE features:
  
  • Temperature threshold control
  • PoE usage threshold control
  • PD alive check
  • PoE schedule 

Layer 3 Features:

• IP dynamic routing protocol supports OSPFv2
• IPv4/IPv6 hardware static routing
• Routing interface provides per VLAN routing mode
• IP interfaces (Max. 128 VLAN interfaces)
• Routing table (Max. 128 routing entries)

Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
  
  • Broadcast/multicast/unknown unicast
• Supports VLAN
  
  • Supports VLAN
  • IEEE 802.1Q tagged VLAN
  • Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad) 
  • Private VLAN Edge (PVE)
  • Protocol-based VLAN
  • MAC-based VLAN
  • Voice VLAN
  • GVRP (GARP VLAN Registration Protocol)
  • Up to 4K VLANs groups, out of 4094 VLAN IDs
• Supports Spanning Tree Protocol
  
  • IEEE 802.1D Spanning Tree Protocol (STP)
  • IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
  • IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
  • BPDU Guard
• Supports Link Aggregation
  
  • 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
  • Maximum 4 trunk groups with 4 ports for each trunk group 
  • Up to 80Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports ERPS (Ethernet Ring Protection Switching)
• Compatible with Cisco uni-directional link detection(UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
• Link Layer Discovery Protocol (LLDP) 

Quality of Service:

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
  
  • IEEE 802.1p CoS
  • TOS/DSCP/IP precedence of IPv4/IPv6 packets
  • IP TCP/UDP port number
  • Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking 

Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD snooping v1 and v2
• Querier mode support
• IPv4 IGMP snooping port filtering
• IPv6 MLD snooping port filtering
• Multicast VLAN Registration (MVR) support  

Security:

• Authentication
  
  • IEEE 802.1x port-based/MAC-based network access authentication
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • TACACS+ login users access authentication
  • RADIUS/TACACS+ users access authentication
  • Guest VLAN assigns clients to a restricted VLAN with limited services
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List
• Source MAC/IP address binding
• DHCP Snooping to filter untrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder 

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
  
  • Console/Telnet Command Line Interface 
  • Web switch management
  • SNMP v1, v2c, and v3 switch management
  • SSHv2, TLSv1.2, SSL and SNMP v3 secure access
• SNMP Management
  
  • Four RMON groups (history, statistics, alarms and events) 
  • SNMP trap for interface Link Up and Link Down notification
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via HTTP/TFTP
  • Reset button for system reboot or reset to factory default
  • Dual images
• DHCP Relay and DHCP Option 82
• DHCP Server
• User Privilege levels control
• NTP (Network Time Protocol)
• Network Diagnostic
  
  • SFP-DDM (Digital Diagnostic Monitor)
  • ICMPv6/ICMPv4 remote ping
  • Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• SMTP/Syslog remote alarm
• System Log
• PLANET Smart Discovery Utility for deployment management
• Smart fan with speed control 

Power Management:

• Dual redundant modular power supply slots
• Supports configurable power operation modes
  
  • Redundant Power Supply (RPS, 1+1): Provides 1+1 power redundancy when two PSUs are installed.
  • Extended Power Supply (EPS, 2+0): Provides more power budget by combining two PSUs to share the maximum power budget
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience

• 24xt 10/100/1000BASE-T Gigabit RJ45 copper
• 2x 1000BASE-X mini-GBIC SFP interfaces

  Power over Ethernet:

• Complies with IEEE 802.3af/at Power over Ethernet end-span PSE
• Up to 24 ports of IEEE 802.3af/802.3at devices powered
• Supports PoE Power up to 32 watts for each PoE port
• Each port supports 54V DC power to PoE Powered Device
• 300-watt PoE budget
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m in standard mode and 250m in extend mode

  Smart LCD:

• LCD switch mode for "Standard", "VLAN" and "Extend" mode selection; the "Extend" mode features 30-watt PoE transmit distance of 250m at speed of 10Mbps and VLAN isolation
• Solid LCD switch mode to isolate ports to prevent broadcast storm and defend DHCP spoofing
• Power low-voltage, power over-voltage and PSE over-temperature protection
• Screen saver, fan control, factory default and save configuration
• PoE management
• Total PoE power budget control
• Per port PoE function enable/disable
• PoE port power feeding priority
• Per PoE port power limitation
• PD alive check

  Switching:

• Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/MDI-X
• Flow control for full duplex operation and back pressure for half duplex operation
• 9216bytes packet size
• Integrates address look-up engine, supporting 8K absolute MAC addresses
• IEEE 802.1Q VLAN transparency
• Automatic address learning and address aging

  Hardware:

• 19-inch desktop size, 1U height, rack mountable
• 2-inch color LCD with smart management functions
• LED indicators for system power, per port PoE ready and PoE activity, speed, Link/Act
• 3 silent fans to provide stable and efficient power performance
• Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az)
• Supports contact discharge of ±6KV DC and air discharge of ±8KV DC for Ethernet ESD protection
• Supports ±6KV surge immunity

• 24x 10/100/1000BASE-T RJ45 copper ports
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 to DB9 console interface for switch basic management and setup
• One 10/100BASE-TX Management port 

Stacking Features:

• IP Stacking
  
  • Connects with stack member via Gigabit TP, SFP and 10G SFP+ interfaces
  • Single IP address management, supporting up to 16 IP units stacked together
• Hardware Stacking
  
  • Virtualized multiple SGS-5240 switch series stacked into one logical device
  • Connects with stack member via assigned 10G SFP+ interfaces
  • Single IP address stack management, supporting up to 6 hardware units stacked together
  • Stacking architecture supports redundant ring mode

IP Routing Features:

• IPv4/IPv6 hardware static routing
• Routing interface provides per VLAN routing mode 

Layer 2 Features:

• Supports VLAN
  
  • IEEE 802.1Q tag-based VLAN
  • Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported
  • GVRP for dynamic VLAN management
  • Protocol-based VLAN
  • MAC-based VLAN
  • IP subnet-based VLAN
  • Voice VLAN
• Supports Link Aggregation
  
  • 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
• Supports Spanning Tree Protocol
  
  • STP, IEEE 802.1D (Classic Spanning Tree Protocol)
  • RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
  • MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
  • Supports BPDU & root guard
• Port mirroring to monitor the incoming or outgoing traffic on a particular port (many to one)
• Supports G.8032 ERPS (Ethernet Ring Protection Switching)
• Loop protection to avoid broadcast loops
• Link Layer Discovery Protocol (LLDP)
• Compatible with Cisco uni-directional link detection (UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices 

Quality of Service:

• Input and output rate limit per port bandwidth control
• 8 priority queues on all switch ports
  
  • IEEE 802.1p CoS/DSCP/IP Precedence
  • VLAN ID
  • ACL
  • Policy-based ingress and egress QoS 

Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD snooping v1 and v2
• Querier mode support
• IPv4 IGMP snooping port filtering
• IPv6 MLD snooping port filtering
• MVR (Multicast VLAN Registration) 

Security:

• Authentication
  
  • IEEE 802.1x port-based/MAC-based network access authentication
  • IEEE 802.1x authentication with guest VLAN
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • RADIUS/TACACS+ users access authentication
  • Guest VLAN assigns clients to a restricted VLAN with limited services
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List (ACL)
  • Time-based ACL
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder 

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
  
  • Console and Telnet Command Line Interface 
  • HTTP web switch management
  • SNMP v1 and v2c switch management
  • SSHv2, SSLv3 and SNMP v3 secure access
• SNMP Management
  
  • Four RMON groups (history, statistics, alarms, and events) 
  • SNMP trap for interface Link Up and Link Down notification
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• • Firmware upload/download via HTTP
  • Reset button for system reboot or reset to factory default
  • Dual images
• DHCP Functions:
  
  • DHCP Relay
  • DHCP Option 82
  • DHCP Server
• User Privilege levels control
• Network Time Protocol (NTP) and SNTP
• Network Diagnostic
  
  • SFP-DDM (Digital Diagnostic Monitor)
  • Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
  • ICMPv6/ICMPv4 remote ping
• Syslog remote alarm
• System Log 

Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus
• Up to 24 ports of IEEE 802.3at PoE devices powered
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE management
  
  • Total PoE power budget control
  • Per port PoE function enable/disable
  • PoE port power feeding priority
  • PD classification detection

• 24 Gigabit-PoE+-Ports
• 4x Gigabit-SFP-Steckplätze
• 802.3at/af, 250 W PoE-Leistung
• 1 HE 19-Zoll-Rack-montierbares Stahlgehäuse
• Features:
  • Integration mit Omada SDN Controller, Static Routing, 802.1Q VLAN, STP/RSTP/MSTP, IGMP Snooping, 802.1p/DSCP QoS, ACL, 802.1x, Radius/Tacacs+ Authentifizierung, LACP, CLI, SNMP, Dual Image, IPv6

• 192W PoE-Leistung: 24× 802.3at/af-konforme PoE+-Ports mit einer Gesamtleistung von 250W*.
• Komplett Gigabit: 24× Gigabit-PoE+-Ports und 4× Gigabit SFP-Slots ermöglichen Hochgeschwindigkeitsübertragungen.
• In Omada-SDN integriert: Zero-Touch Provisioning (ZTP)**, zentralisiertes Cloud-Management, intelligente Netzwerküberwachung.
• Zentralisiertes Management: Der Cloudzugriff und die Omada-App ermöglichen eine sehr komfortable, einfache Verwaltung.
• Statisches Routing: Routet internes Datenverkehr für eine effizientere Netzwerknutzung.
• Solide Sicherheitsstrategien: IP-MAC-Port Binding, ACL, Port Security, DoS Defend, Storm conntrol, DHCP Snooping, 802.1X, Radius Authentication und mehr.
• Optimierte Voice- und Video-Anwendungen: L2/L3/L4 QoS und IGMP Snooping.
• IPv6: IPv6 Unterstützung mit dual IPv4/IPv6 stack, MLD snooping, IPv6 neighbor discovery.

• 24x Gigabit PoE+ Ports
• 4x Gigabit-SFP Slots
• RJ45/Micro-USB-Konsolen Port
• 802.3at/af, 384 W PoE-Leistung
• 1HE 19-Zoll-Rack-montierbares Stahlgehäuse
• Features:
  • Statisches Routing, 802.1Q VLAN, QinQ, STP/RSTP/MSTP, IGMP Snooping, 802.1p/DSCP QoS, ACL, 802.1x, Radius/Tacacs+ Authentifizierung, LACP, CLI, SNMP, Dual Image/Konfiguration, IPv6

• 384W PoE-Leistung: 24× 802.3at/af konforme PoE+ ports mit einer Gesamtleistung von 384W*.
• Komplett Gigabit: 24× gigabit PoE+ ports und 4× gigabit SFP Slots ermöglichen Hochgeschwindigkeitsübertragungen.
• In Omada-SDN integriert: Zero-Touch Provisioning (ZTP)**, Zentralisiertes Cloudmanagement und intelligent Netzwerküberwachung.
• Zentralisiertes Management: Der Cloudzugriff und die Omada-App ermöglichen eine sehr konfortable, einfache Verwaltung.
• Statisches Routing: Routet internes Datenverkehr für eine effizientere Netzwerknutzung.
• Solide Sicherheitsstrategien: IP-MAC-Port Binding, ACL, Port Security, DoS Defend, Storm conntrol, DHCP Snooping, 802.1X, Radius Authentication und mehr.
• Optimierte Voice- und Video-Anwendungen: L2/L3/L4 QoS und IGMP Snooping.
• Standalone-Management : Web, CLI (Console Port, Telnet, SSH), SNMP, RMON und nd Dual Image ermöglichen ein vollständiges Management.

• 24x Gigabit PoE+ Ports
• 4x 10G SFP+ Slots
• RJ45/Micro-USB Konsolen Port
• 802.3at/af, 384 W PoE Power
• 1HE 19-Zoll-Rack-montierbares Stahlgehäuse
• Features:
  • Integration mit Omada SDN Controller, Static Routing, OAM, sFlow, DDM, 802.1Q VLAN, QinQ, STP/RSTP/MSTP, IGMP Snooping, 802.1p/DSCP QoS, ACL, 802.1x, Radius/Tacacs+ Authentifizierung, LACP, CLI, SNMP, Dual-Image/Konfiguration, IPv6

• Blitzschnelle 10G Uplinks: 4× 10Gbit/s SFP+-Slots und die volle Switchkapazität sichern die volle Uplinkbandbreite high-bandwidth connectivity and non-blocking switching capacity. 
• 384W PoE-Leistung: 24× 802.3at/af-konforme PoE+-Ports haben einea total power supply of 384 W*.
• In Omada integriert: Zero-Touch Provisioning (ZTP)**, zentrales Cloud Management und intelligentes Monitoring.
• Zentrales Management: Cloudzugriff und Omada App für eine ultra einfache und praktische Verwaltung.
• Statisches Routing: Hilft bei der Weiterleitung von internen Datenübertragungen für eine effizientere Nutzung der Netzwerkressourcen.
• Robust Security Strategies: IP-MAC-Port Binding, ACL, Port Security, DoS Defend, Storm control, DHCP Snooping, 802.1X, Radius Authentication und mehr.
• Optimize Voice and Video Applications: L2/L3/L4 QoS and IGMP snooping.
• Standalone Management: Web, CLI (Console Port, Telnet, SSH), SNMP, RMON und Dual Image liefern leistungsstarke Managementkapazitäten

• Optimiert für UniFi
• 24 Ports Gigabit PoE+
• 2 SFP Ports
• max 250 Watt Output
• Rackmontage

  Ubiquiti UniFi Switch Der Ubiquiti UniFi Switch ist ein PoE+ Gigabit Switch. Der Switch ermöglicht die simultane Verarbeitung von Traffic mit 26 Gbps (24 Port Modell) und 70Gbps (48 Port Modell) auf allen Ports ohne Paketverlust.   PoE+ Funktionalität Der Switch unterstützt sowohl Active- als auch Passive-POE (IEEE 802.af / IEEE 802.3at / 24 Volt passive) und versorgt Geräte dieser Standards mit Strom.   Leistungsstarke Hardware mit 1-Gbit Uplink (SFP) Der 24 Port UniFi Switch hat 2 SFP Ports welche Glasfaserverbindungen mit bis zu 1 Gbps ermöglichen.   Der UniFi Controller Die UniFi Controller Software ermöglicht den Administratoren die Verwaltung des UniFi Switches und aller anderen UniFi Geräte über eine graphische Oberfläche. Die Software ist frei erhältlich und kann über www.ubnt.com heruntergeladen werden.   Multi-Site Management Eine Instanz des UniFi Controllers in der Cloud ermöglicht die zentralisierte Verwaltung von mehreren UniFi Instanzen von verschiedenen Standorten. Jede Instanz hat sein eigenes Netzwerk Monitoring.   Switch Konfiguration Die Konfiguration des Switches erfolgt über die UniFi Software, so lassen sich verschiedene Features nutzen wie z.B.:

• PoE Einstellung für jeden einzelnen Port