• Designed to extend wireless coverage of 802.11b/g/n devices at frequency of 2.4GHz
• Intergrating two polarities into one antenna helps to reduce cost of deployment
• 14dBi high-gain antenna
• IP55-rated case
• Compact-sized housing and lightning protection system design
• Built-in two N-Type female connectors
• Easily-extended, point-to-point wireless coverage

  PLANET ANT-FP14AD is a 5GHz 14dBi Flat Panel Dual Polarization Directional Antenna equipped with two N-Type Female connectors. The ANT-FP14AD can increase wireless signal coverage and improve signal strength and quality for the current wireless environment. As the ANT-FP14AD can effectively enhance the performance and coverage of the 802.11a/n 5GHz facilities, it is quite suitable for outdoor wireless LAN applications, such as point-to-point connection between the warehouses.   The ANT-FP14AD Dual Polarization Directional Antenna can operate in both vertical and horizontal polarization. The dual-polarized antennas are perfectly helpful for 802.11n devices in multithreaded communications. This enables the wireless device to transmit data on one polarization and receive data on the other polarization simultaneously. Obviously, all the networking equipment in the wireless network must be multithreading complaint. It thus brings users the advantage that multithreaded communications can be achieved with use of only one antenna instead of two independent (and opposite polarized) antennas.

• Designed to extend wireless coverage of 802.11b/g/n devices at frequency of 2.4GHz
• Intergrating two polarities into one antenna helps to reduce cost of deployment
• 14dBi high-gain antenna
• IP55-rated case
• Compact-sized housing and lightning protection system design
• Built-in two N-Type female connectors
• Easily-extended, point-to-point wireless coverage

  PLANET ANT-FP14D is a 2.4GHz 14dBi Flat Panel Dual Polarization Directional Antenna equipped with two N-Type Female connectors. The ANT-FP14D can increase wireless signal coverage and improve signal strength and quality for the current wireless environment. As the ANT-FP14D can effectively enhance the performance and coverage of the 802.11b/g/n 2.4GHz facilities, it is quite suitable for outdoor wireless LAN applications such as point-to-point connection between the warehouses.   The ANT-FP14D Dual Polarization Directional Antenna can operate in both vertical and horizontal polarization. The dual-polarized antennas are perfectly helpful for 802.11n devices in multithreaded communications. This enables the wireless device to transmit data on one polarization and receive data on the other polarization simultaneously. Obviously, all the networking equipment in the wireless network must be multithreading complaint. It thus brings users the advantage that multithreaded communications can be achieved with use of only one antenna instead of two independent (and opposite polarized) antennas.

• 30 degree Horizontal Spread and 20 degrees Vertical Spread
• Connector: N-female
• Operating environment: outdoor

  PLANET ANT-CM5 dual-band ceiling mount antenna provides the maximum flexibility for users to connect the antenna for all their wireless APs as it supports both 2.4GHz and 5GHz (dual-band). You can connect the ANT-CM5 to your entire wireless network devices without any concern.

• 30 degrees Horizontal Spread and 20 degrees Vertical Spread
• Connector: N-female
• Operating environment: outdoor

  To commit itself to the wireless long distance connectivity, PLANET WireFree provides a variety of antennas, cables and other accessories for 2.4GHz and 5GHz ISM band applications where more RF gain power is required to increase the convergence of the installations in the wireless state.

• 360 degree Horizontal Spread and 6 degree Vertical Spread
• Connector: N-female
• Operating environment: outdoor

  To commit itself to the wireless long distance connectivity, PLANET WireFree provides a variety of antennas, cables and other accessories for 2.4GHz and 5GHz ISM band applications where more RF gain power is required to increase the convergence of the installations in the wireless state.

• 360 degrees Horizontal Spread & 10 degrees Vertical Spread
• Connector: N-female
• Operating environment: outdoor

  To commit itself to the wireless long distance connectivity, PLANET WireFree provides a variety of antennas, cables and other accessories for 2.4GHz and 5GHz ISM band applications where more RF gain power is required to increase the convergence of the installations in the wireless state.

• Compatible with 2.4/5GHz 802.11n devices
• Optimal 4.5dBi high gain in 2.4GHz and 7dBi high gain in 5GHz
• Flexible N-type plug (male) connector fits all outdoor wireless equipment with an N-type jack (female)　antenna connector
• IP55 case protection
• Compact-sized housing, lightning design
• 360 degrees of wireless network coverage, no aiming required
• No configuration or installation software required

  Full 360° Coverage with Greater Penetration PLANET ANT-OM5D-KIT is a 2.4/5GHz Dual Band Antenna equipped with N-type male connector. The antenna provides a 360-degree horizontal and wider vertical coverage which is quite suitable for outdoor short-range application, especially to provide the wireless access for laptops and smartphones.   With its N-type male connector, it can be directly attached to the antenna connectors of the WNAP-6350, WNAP-7350 and WDAP-8350 without any cumbrous cabling, thus reducing the deployment cost and installer’s effort.

• 360 degrees Horizontal Spread & 10 degrees Vertical Spread
• Connector: N-female
• Operating environment: outdoor

  To commit itself to the wireless long distance connectivity, PLANET WireFree provides a variety of antennas, cables and other accessories for 2.4GHz and 5GHz ISM band applications where more RF gain power is required to increase the convergence of the installations in the wireless state.

• 2x2 MIMO  dual-polarity sector antenna
• Powerful gain of 17dBi  and frequency of 5150～5850MHz 
• Half-power beamwidth (H: 90 degrees, V: 7 degrees)
• Transmittance distance of up to 5km
• IP67 rating
• 2 N-type female connectors

Boost Long-range Wireless Coverage in Point-to-Multipoint Networks:
PLANET brand-new Dual-polarity Sector Antennas feature 2x2 MIMO technology with 17dBi high-gain signal sensitivity and 90-degree sectorial coverage, and are equipped with two N-type female connectors. They are perfectly helpful for 802.11n and 802.11ac outdoor wireless access points in multithreaded communications as they offer a maximum throughput of 300Mbps or 866Mbps for long-distance Point-to-Multipoint coverage and wireless applications. As the ANT-SE17AD can effectively enhance the performance and coverage of the 802.11ac 5GHz environment, it is also quite suitable for outdoor wireless LAN applications, such as point-to-point connection between the warehouses. Fast and Space-saving 2x2 MIMO Antenna:
The MIMO sector antenna enables the wireless device to transmit data on one polarization and receive data on the other polarization simultaneously. It thus brings users the advantage of having multithreaded communications with use of only one antenna instead of two independent antennas. Tough Outdoor Installation:
The new MIMO Sector Antenna is housed inside a rugged and weatherproof IP67-rated radome UPVC enclosure, and thus can withstand any harsh weather conditions. They come with adjustable angle brackets for adjusting the coverage angle from 0 to 10 degrees.

• 5-Port 10/100/1000 BASE-T Gigabit RJ45 Kupfer mit 4-Port IEEE 802.3at/af PoE-Injektor (Port 1 bis Port 4)
• RJ45-Typ-Schnittstelle für Management und Setup
• USB-Typ A-Buchse für Sicherung und Wiederherstellung von Dateien

  Power over Ethernet:

• Kompatibel mit IEEE 802.3at Power-over-Ethernet-Endspan-PSE
• Rückwärtskompatibel mit IEEE 802.3af Power over Ethernet
• Bis zu 4 Ports versorgen IEEE 802.3af/802.3at-Geräten mit Strom
• Unterstützt PoE Power bis zu 30 Watt für jeden PoE Port
• Automatische Erkennung der PoE-Geräte (PD)
• Der Schaltungsschutz verhindert Stromstörungen zwischen den Ports
• Fernspeisung bis zu 100 Meter
• PoE-Verwaltung
• PoE-Gesamtbudgetkontrolle
• Pro Port PoE-Funktion aktivieren / deaktivieren
• PoE-Port-Stromversorgungspriorität
• PoE-Port-Leistungsbegrenzung
• PD Alive-Check
• PoE-Zeitplan

  Batteriemanagement:

• Batterietyp Option: Nickel-Cadmium-Batterie oder Lead-Acid-Batterie
• Einfache Diagnose des Systembetriebszustands über LED-Anzeige
• Batteriestromverbrauch und -status
• Batteriekapazität und Energieverbrauchsstatistik
• Niederspannungs-Abschaltschutz: Warnmeldung senden und den PoE-Anschluss niedriger Priorität für den Niederleistungsakku abschalten
• Pulsbreitenmodulation (PWM) Schutz
• Gegenstromschutz, um zu verhindern, dass die Stromkreise zum PV-Panel zurückfließen
• Überstrom- und Übertemperaturschutz
• Verpolungsschutz (für Batterie- und Ladeelektroden)

  Industrieller Fall u. Installation:

• IP30 Aluminiumgehäuse
• DIN-Schiene und wandmontierter Entwurf
• Unterstützt -10 bis 60 Grad C Betriebstemperatur
• Unterstützt ESD 6KV DC Ethernet-Schutz
• Redundantes Power-Design
• 24V ~ 45V DC Weitstromanschluss

  Switiching:

• Hardwarebasierte 10/100Mbps (Halb-/Vollduplex), 1000Mbps (Vollduplex), Auto-Negotiation und Auto MDI / MDI-X
• Verfügt über Store-and-Forward-Modus mit Wire-Speed-Filter- und Weiterleitungsraten
• IEEE 802.3x Flusskontrolle für Full-Duplexbetrieb und Back Pressure für Half-Duplexbetrieb
• 8K MAC-Adresstabelle Größe
• Automatisches Adresslernen und Adressaltern

  Router:

• Internet-Typen: Dynamische IP, statische IP, PPPoE, L2TP, PPTP
• Statisches und dynamisches Routing (RIP1 und 2)
• IP / MAC-basierte Bandbreitenkontrolle
• Unterstützt Port Forwarding, DMZ, UPnP und Dynamic DNS für verschiedene Netzwerkanwendungen
• 802.1d STP- und IGMP-Proxy

  Sicherheit:

• Mithilfe der Portfilterung können Sie entweder zulassen oder verhindern, welche Anwendungen auf das Internet zugreifen können.
• Mit der MAC-Filterung können Sie Computer und Geräte basierend auf ihrer MAC-Adresse ein- oder ausschließen
• Mithilfe der URL-Filterung können Sie den Zugriff auf Internetwebsites in einer URL-Liste steuern
• Der IP-Quellenschutz verhindert IP-Spoofing-Angriffe
• Schutz vor DoS-Angriffen

  Management:

• Switch-Verwaltungsschnittstelle
• IPv4-Web-Switch-Verwaltung
• SNMP v1, v2c
• Statisch und DHCP für die IP-Adresszuweisung
• Systemwartung
• Firmware Upload / Download über HTTP
• Konfiguration Upload / Download über HTTP
• Hardware-Reset-Taste für Systemneustart oder Zurücksetzen auf Werkseinstellungen
• NTP-Netzwerkzeitprotokoll
• SNMP-Trap für die Schnittstelle Link-Up- und Link-Down-Benachrichtigung
• Ereignisprotokollierung auf dem Remote-Syslog-Server
• PLANET Smart Discovery Utility

   

• UPnP AV / DLNA / HomePlug AV Compliant
• Integrated Gigabit Ethernet and S/PDIF
• Full HD (1080) and HDMI
• Multi-Language and Multi-Media Formats
• Stream videos, music and photos
• Internet Browser and BitTorrent
• Favorite Web TV / Photo / Radio Station Galley
• Wizard Easy Setup and User-friendly Graphical On-Screen Menu

  PLANET DMA-200 Digital Media Center is an advanced customer premises equipment (CPE) for delivering streaming audio, video, and data directly from network or Internet to consumers’ TV sets and/or Home Entertainment systems. If you have already set up your local area network or connected to Internet, you can huddle on the sofa using supplied remote control to search and enjoy your favorite pictures, movies, or surf webs but no need to always be seated next to your computer or Home Entertainment systems. Besides connecting your PC/NAS with the network, you can simply plug in your USB devices to access and play the media files via user-friendly On-Screen Display (OSD) menu.   In order to meet your need of surfing Internet on TV, the DMA-200 provides web browser, bit torrent download and Internet radio function so you can freely choose these features and enjoy an amazing variety of Internet video contents.   With the fascinating features, the DMA-200 provides advanced MPEG1/2/4 video and MP3 audio compression algorithms and can deliver content streams with optimal quality over networks with limited bandwidth. PLANET DMA-200 provides an immersive way of managing and interacting with your entertainment library so that you are able to explore your complete digital collections of music, photos, and videos in a single window. The DMA-200 is a powerful Digital Media Center supporting Standard and High Definition (HD) video, audio/video playback, web browsing and a myriad of media applications.

• 20 KA lightning surge protection
• Two passive 10 / 100 / 1000 Ethernet ports
• One ground position
• Flexibly designed for various Ethernet devices including PoE

  To prevent Ethernet devices from possible damage caused by surge voltages as a result of lightning strikes, PLANET has released a new Ethernet Lightning Arrest Box especially made in the current Ethernet environment.   The ELA-100 Ethernet Lightning Arrest Box provides two passive 10 / 100 / 1000Base-T interfaces for connection of two Ethernet devices and one ground position for earth. The ELA-100 Ethernet Lightning Arrest Box is the ideal solution to preventing damages to Ethernet devices from surge voltages caused by lightning strikes.

• One 1000Base-SX / LX SFP slot
• PCI Express x1 Host Bus interface
• 9K Jumbo Frame
• IP, TCP checksum offloading
• IEEE 802.1Q Tagged VLAN
• Low Power Consumption
• Windows XP/2003, Vista/2008, Win7, Linux, and MAC OS X Ready

  High Performance Boosts Network Traffic Speed and Flexible Distance Extension PLANET ENW-9701 1000Base-X Fiber PCI-Express Ethernet adapter is ideal for high end servers to extend long distance network reliably and flexibly with up to 2000Mbps full-duplex bandwidth capacity. It is an optimal solution for Ethernet applications by providing strictly low-power budgets and small form factor.   Flexible Distance Option With the 1000Base-SX / LX SFP (Small-Form Factor Pluggable) interface supported by the ENW-9701, the fiber network deployment distance can be extended from 550 meters (via multi-mode fiber) up to above 10/20/30/40/50/70/120 kilometers (via single-mode fiber, respectively). Users can choose the most suitable SFP transceiver module depending on their needs. The ENW-9701 connects your servers and workstations, guaranteeing extremely high throughput and excellent signal quality.   More Bandwidth and Advanced Functions The ENW-9701 is designed to address high-performance system requirements. With the innovative PCI Express Bus Architecture, the ENW-9701 provides better bandwidth and performance than the network cards which are based on 32/64bit PCI architecture. Moreover, the ENW-9701 supports IEEE 802.1Q VLAN which allows it to operate in a flexible and secure network environment. With 9K Jumbo Frame ability and IEEE 802.3 Flow Control support, it offers further optimal throughput and wire-speed packet transfer performance without risk of packet loss. The high data throughput of the device makes it ideal for most Gigabit Ethernet environments.   Seamless Integration The ENW-9701 is completely harmonious with most of the servers’ operating systems, enabling simple integration into network designs. There is no need of any modification to the server's operating system or any special software required for the ENW-9701 to be integrated into the system. The ENW-9701 can take the place of the Ethernet MAC of any conventional TCP connection and have the existing TCP/IP stack of server’s CPU still kept intact. It requires only a simple, standard PCIe driver to connect the ENW-9701 to the software.

• Intel ® server-grade GbE Mac Controller
• PCI Express (PCIe) x4 slot
• Supports 2-port Gigabit Ethernet MAC Controller
• IEEE 802.3at compliant with up to 30W power per port with a total power budget of 60W
• PCI Express 12V power supply without external power input
• Powered device (PD) auto detection and classification
• IEEE 802.1q VLAN ID tagged
• 9.5K jumbo frame size
• Low profile and full-height bracket
• Complies with Microsoft, Linux and Mac platforms

Simple Plug and Play PoE Solution for IPC System:
PLANET ENW-9720P is a 2-port 10/100/1000T 802.3at PoE+ PCI Express server adapter with a maximum of up to 60 watts of power output over Ethernet cables. Incorporated with Intel server-grade GbE Mac controller, the ENW-9720P provides superb performance to fulfill the requirements of Industrial networks. Complied with PCIe standard, the ENW-9720P can be easily installed on any IPC or server motherboard with a PCIe socket to make the IPC or server able to communicate with other Ethernet devices and deliver power to PD devices. Each port of the ENW-9720P can deliver 30W of power and 1000 Mbps bandwidth over a networking cable of up to 100 meters. Its 30W PoE+ can now power not only PTZ (pan, tilt and zoom) cameras for surveillance applications but also 802.11ac AP for ultra-high-speed wireless application. Hassle-free Installation for PoE Deployment:
PLANET ENW-9720P is backward compatible with both IEEE 802.3af/at PoE standards which allow users to flexibly deploy standard and high powered devices to transfer data and power simultaneously through one Ethernet cable for up to 100 meters.  In addition, the ENW-9720P is powered by bus power without an external power input. Thus, an additional electrical outlet is not necessary. With PoE application, the ENW-9720P frees the IP camera and wireless AP deployment from restrictions of power outlet locations and the additional AC wiring. It reduces cables and eliminates the need for electrical outlets on the wall, ceiling or any unreachable place, and most of all, it reduces installation time.  Standard 802.1Q VLAN Support:
The ENW-9720P supports IEEE 802.1Q VLAN which allows it to operate in a flexible and secure network environment. With 9.5K jumbo frame ability and IEEE 802.3 flow control support, it further optimizes throughput and wire-speed packet transfer performance without the risk of packet loss. The high data throughput of the device makes it ideal for most Gigabit Ethernet environments. Multiple OS Support:
The ENW-9720P operates completely well with most of the popular and latest operating systems including Microsoft Windows Server, Linux and VMware, enabling simple integration into network designs. There is no need of any modification to the server's operating system or any special software required for the ENW-9720P to be integrated into the system. Low Profile design:
The ENW-9720P supports both full-height and low profile PCI Express slot. The ENW-9720P provides an accessory of low profile bracket to fulfill IPC with low profile slot. The flexibility of low profile design can help the ENW-9720P meet various applications of industrial networks.

• Intel ®  server-grade GbE Mac Controller
• PCI Express (PCIe) x4 slot
• Supports 4 Gigabit Ethernet MAC Controller
• IEEE 802.3at compliant with up to 30W power per port
• Supports 12V DC 4-pin Molex input
• Powered device (PD) auto detection and classification
• IEEE 802.1q VLAN ID tagged
• 9.5K jumbo frame size
• Complies with Microsoft, Linux and MAC platforms

Flexible PoE Expansion Leverages Existing IPC/Server Environment:
PLANET ENW-9740P is a 4-port 10/100/1000T 802.3at PoE+ PCI Express server adapter with a maximum of up to 120 watts of power output over Ethernet cables. 95W is suggested, depending on usage. Complied with PCI-E standard, the ENW-9740P can be installed on any IPC or server motherboard with PCI-E socket to make the IPC or server able to communicate other Ethernet devices and deliver power to PD devices. Each port of the ENW-9740P can deliver 30W of power and 1000 Mb/s bandwidth over a networking cable of up to 100 meters. Its 30W PoE+ can now power not only PTZ (pan, tilt and zoom) cameras for surveillance applications but also 802.11ac AP for ultra-high-speed wireless application. Hassle-free Installation for PoE Deployment:
PLANET ENW-9740P is backward compatible with both IEEE 802.3af/at PoE standards which allow users to flexibly deploy standard and high powered devices to transfer data and power simultaneously through one Ethernet cable for up to 100 meters.   With PoE application, the ENW-9740P frees the IP camera and wireless AP deployment from restrictions of power outlet locations and the additional AC wiring. It reduces cables and eliminates the need for electrical outlets on the wall, ceiling or any unreachable place, and most of all, it reduces installation time.  Standard 802.1Q VLAN Support:
The ENW-9740P supports IEEE 802.1q VLAN which allows it to operate in a flexible and secure network environment. With 9.5K jumbo frame ability and IEEE 802.3 flow control support, it further optimizes throughput and wire-speed packet transfer performance without the risk of packet loss. The high data throughput of the device makes it ideal for most Gigabit Ethernet environments. Multiple OS Support:
The ENW-9740P operates completely well with most of the popular and latest operating systems including Microsoft Windows Server, Linux and VMware, enabling simple integration into network designs. There is no need of any modification to the server's operating system or any special software required for the ENW-9740P to be integrated into the system.

• PCI Express rev. 2.0 specification x4 Interface
• IP, TCP, UDP checksum offloading
• IEEE 802.1Q VLAN ID Tagged / IEEE 802.1q Qos
• 16K Jumbo Frame Size
• IEEE 802.3x Full-Duplex Flow Control
• Complies with Microsoft and Linux Platform

  Enhanced from the current highly-praised version, PLANET has released a brand-new version of the 10Gbps SFP+ PCI Express Server Adapter – the ENW-9801 version 2. The new version of the ENW-9801 is upgraded with PCI Express rev. 2.0 specification x4 interface and other advanced features as follows:

• Smaller and Compact in design
• Flexible 10G SFP+ Module Installation
• Low Profile Bracket  

   The Server Level Adapter to Expand Networking Environments The ENW-9801 is a PCI Express 10Gbps Ethernet Adapter designed to meet high-performance system application requirements. With the innovative PCI Express Bus Architecture, the ENW-9801 provides superior performance than the network cards based on 32/64bit PCI architecture. It provides the best solution to one of the major issues of Server Farm Networks -- communication speed. Ten times faster than the existing 1000Base-SX/LX fiber solutions, PLANET ENW-9801 is designed to connect your servers and workstations, guaranteeing extremely high throughput and excellent signal quality. Moreover, the ENW-9801 supports IEEE 802.1Q VLAN which allows it to operate in a flexible and secure network environment. With 16K Jumbo Frame ability and IEEE 802.3 Flow Control support, it further optimizes throughput and wire-speed packet transfer performance without risk of packet loss. The high data throughput of the device makes it ideal for most 10 Gigabit Ethernet environments.    10 Gigabit Performance Boosts Network Traffic The ENW-9801 is an optimal solution to Ethernet applications by providing low-power budgets and small form factor. It offers simple integration into any PCI Express x4 server slot via one SFP+ slot. The onboard controller featured on the ENW-9801 integrates embedded technology and a 10GbE MAC into a single chip that offers up to 10Gbps of network throughput. PLANET Network solution greatly reduces the TCP/IP packet processing tasks of the server’s CPU by performing enhanced data-handling algorithms, thereby providing nearly 10Gb line speed performance with the simplicity of a conventional Network Interface Card (NIC).

• PCI Express rev. 2.0 specification x4 Interface
• 10Gbps throughput with 100-meter UTP cable
• Backward compatible with 1000Base-T, 100Base-TX network
• IP, TCP, UDP checksum offloading
• IEEE 802.1Q VLAN ID Tagged / IEEE 802.1q QoS
• Reduced CPU utilization and improved throughput
• Wake-on-LAN
• 16K jumbo frame size
• IEEE 802.3x full-duplex flow control
• Complies with Microsoft and Linux platforms

  Low Cost, Low Power, 10 Gigabit Performance To welcome the dawning of the new 10G-network generation, PLANET has released a brand-new 10Gbps PCI Express Server Adapter – the ENW-9803. It comes with one 10GBase-T RJ-45 interface and low-profile PCI Express form factor, and is designed to address system application requirements by offering the best cost, 10Gbps high-performance, low-power consumption and better-quality solution in the 10Gbps network market today. With throughput up to 10 times that of the existing 1000Mbps solutions, PLANET ENW-9803,used for Application Servers and Network Attached Storages (NAS), guarantees extremely high throughput and excellent signal quality for the existing Ethernet infrastructure.      Cost-effective and Ideal 10G Adapter Compared with 10G adapter with CX4 and SFP+ interface, PLANET 10GBase-T PCI-E adapter is the best choice in that the ENW-9803 10GBase-T can reach up to 100 meters over Cat.6a or Cat.7 RJ-45 cable, whereas the CX4 interface only can extend up to 15 meters in distance. The cost is too high for having an extra SFP+ interface for the SFP+ transceiver. However, with the ENW-9803, customers only spend on Cat.6a or Cat.7 cable as the ENW-9803 is bundled with RJ-45 connector, thus costing less than the SFP+ transceiver.   Server Level Adapter to Expand Networking Environments The ENW-9803 is an optimized 10GbE device designed for low-power, low-cost and single-port applications required in application servers, high-end workstations and personal computers. This makes it ideal for enabling 1GbE to 10GbE migration in bandwidth-intensive workstation applications and for low-end to mid-range network appliances. With the innovative PCI Express Bus Architecture, it offers increased bandwidth, reliability and additional functionality compared with standard GbE network cards. The performance of throughput at rates up to 20Gbps is unbelievable, thus eliminating the bottleneck that exists with the current Gigabit network. PLANET ENW-9803 is designed to connect your servers and workstations, guaranteeing extremely high throughput and excellent signal quality.   Standard 802.1Q VLAN Support Moreover, the ENW-9803 supports IEEE 802.1Q VLAN which allows it to operate in a flexible and secure network environment. With 16K jumbo frame ability and IEEE 802.3 flow control support, it further optimizes throughput and wire-speed packet transfer performance without risk of packet loss. The high data throughput of the device makes it ideal for most 10 Gigabit Ethernet environments.   Multiple OS Support The ENW-9803 operates completely well with most of the popular and latest operating systems including Microsoft Windows Server, Linux and VMware, enabling simple integration into network designs. There is no need of any modification to the server's operating system or any special software required for the ENW-9803 to be integrated into the system.

• 1 : 32 High Split Ratio
• Low Insertion Loss
• Low PDL (Polarization Dependent Loss)
• High Reliability and Stability
• Wide Operating Wavelength 1260 to 1650nm
• Wide Operating Temperature -40°C to 85°C

   

• 1 : 64 High Split Ratio
• Low Insertion Loss
• Low PDL (Polarization Dependent Loss)
• High Reliability and Stability
• Wide Operating Wavelength 1260 to 1650nm
• Wide Operating Temperature -40°C to 85°C

 

• 1 : 8 High Split Ratio
• Low Insertion Loss
• Low PDL (Polarization Dependent Loss)
• High Reliability and Stability
• Wide Operating Wavelength 1260 to 1650nm
• Wide Operating Temperature -40°C to 85°C

 

• 8x 10/100Mbps Fast Ethernet ports
• 1x 10/100/1000BASE-T Gigabit Ethernet port
• 1x 1000BASE-X mini-GBIC SFP interface

  Power over Ethernet:

• Complies with IEEE 802.3af/at Power over Ethernet end-span
• Up to 8 IEEE 802.3af/2 IEEE 802.3at devices powered
• Supports PoE power up to 30 watts for each PoE port
• 120-watt PoE budget
• 8 ports supporting 52V DC power to PoE powered device (Ports 1 to 8)
• Hardware DIP switch for "Standard", "VLAN' and "Extend" mode selection; the "Extend" mode features 30-watt PoE transmit distance of 250m at speed of 10Mbps and VLAN isolation
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m in the standard mode

  Switching:

• Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/MDI-X
• Flow control for full duplex operation and back pressure for half duplex operation
• Integrates address look-up engine, supporting 4K absolute MAC addresses
• Automatic address learning and address aging
• Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP spoofing

  Hardware:

• 9-inch desktop size, 1U height, mountable
• LED indicators for PoE ready/activity and LINK/ACT
• Fanless design
• Internal AC power supply
• Support Energy-Efficient Ethernet (EEE) function (IEEE 802.3az)

Physical Port

• 16-port 10/100Base-TX RJ-45 copper with PoE in-line supported
• 2-port 10/100/1000Base-T RJ-45 copper
• 2 1000Base-X mini-GBIC/SFP slots to share with Port-17 to Port-18
• Reset button for system management

  PoE

• Complies with IEEE 802.3at High Power over Ethernet End-Span PSE
• Complies with IEEE 802.3af Power over Ethernet End-Span PSE
• Up to 16 IEEE 802.3at / 802.3af devices powered
• Supports PoE Power up to 30.8 watts for each PoE port
• Detects powered device (PD) automatically
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m
• PoE Management

- Per port PoE function enable/disable - PoE Port Power feeding priority - Per PoE port power limit - PD classification detection - PoE Power sequential - PoE schedule   Layer 2 Features

• Auto-MDI/MDI-X detection on each RJ-45 port
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Supports broadcast storm control
• Supports VLAN:

- IEEE 802.1Q tag-based VLAN, up to 32 VLANs groups, out of 4095 VLAN IDs - Port-based VLAN, up to 16 VLAN groups - MTU VLAN (Multi-tenant Unit VLAN)

• Supports Link Aggregation

- 802.3ad Link Aggregation Control Protocol (LACP) - Cisco ether-channel (Static Trunk)

• Supports Spanning Tree Protocol

- STP, IEEE 802.1d Spanning Tree Protocol - RSTP, IEEE 802.1w Rapid Spanning Tree Protocol

• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Provides port mirror (Many-to-1)
• Loopback protection to avoid broadcast loops

  Quality of Service

• 2 priority queues on all switch ports
• Traffic classification

- Port-based priority - IEEE 802.1p-based priority - IP TOS / DSCP-based priority - TCP / UDP port-based QoS

• Strict priority and Weighted Round Robin (WRR) CoS policies

  Multicast

• Supports IGMP Snooping v1 and v2

  Security

• Physical port to MAC address binding
• TCP/UDP port number filter: Forwarding or discarding typical network applications
• Port mirroring to monitor the incoming or outgoing traffic on a particular port

  Management

• Switch Management Interfaces

- Web switch management - SNMP v1 switch management

• Supports DHCP Option82 and DHCP Relay
• Firmware upload/download via HTTP
• Hardware reset button for system reboot or reset to factory default

  Ideal Solution for Secure IP Surveillance Infrastructure Particularly designed for the growing popular IP surveillance applications, PLANET FGSW-1816HPS 802.3at PoE web smart switch is positioned as a surveillance switch with the central management of remote power control and IP camera monitoring. The FGSW-1816HPS provides intelligent PoE functions along with 16 10/100Base-TX ports featuring 30-watt 802.3at PoE+ with RJ-45 copper interfaces and 2 Gigabit TP/SFP combo interfaces supporting high-speed transmission of surveillance images and videos.    Perfectly- integrated Solution for PoE IP Camera and NVR System Being different from the general IT industrial PoE switch which usually contains 12 or 24 PoE ports, the FGSW-1816HPS provides 16 802.3at PoE+ ports for catering to medium to large scale of IP surveillance networks at a lower total cost. With its 7.2Gbps high-performance switch architecture and 220-watt PoE power budget, the recorded video files from 16 PoE IP cameras can be powered by the FGSW-1816HPS and saved in the 8 / 16 / 32-channel NVR systems or surveillance software to perform comprehensive security monitoring. For instance, one FGSW-1816HPS can be combined with one 16-channel NVR and 16 PoE IP cameras as a kit for the administrators to centrally and efficiently manage the surveillance system in the local LAN and the remote site via Internet.    Intelligent LED Indicator for Real-time PoE Usage The FGSW-1816HPS helps users to monitor the current status of PoE power usage easily and efficiently by its advanced LED indication. Called “PoE Power Usage”, the front panel of the FGSW-1816HPS Fast Ethernet PoE+ Switch has four orange LEDs indicating 50W, 100W, 150W and 190W of PoE power usage.    PoE Schedule for Energy Saving Besides being used as an IP Surveillance, the FGSW-1816HPS is certainly applicable to constructing any PoE network including VoIP and wireless LAN. Under the trend of energy saving worldwide and contributing to environmental protection on the Earth, the FGSW-1816HPS can effectively control the power supply besides its capability of giving high watts power. The “PoE schedule” function is for you to enable or disable PoE power feeding for each PoE port during specified time intervals and it is a powerful function to help SMBs or enterprises save power and money.    Robust Layer 2 Features The FGSW-1816HPS can be programmed for advanced switch management functions such as dynamic port link aggregation (LACP), Spanning Tree Protocol (STP), IGMP Snooping v1, v2, bandwidth control and L2/L4 security control. The FGSW-1816HPS provides IEEE 802.1Q tagged VLAN, port-based VLAN and MTU VLAN. The VLAN groups allowed will be maximally up to 32. Via aggregation of supporting ports, the FGSW-1816HPS allows the operation of a high-speed trunk combining multiple ports and supports fail-over as well.   Flexible and Extendable Uplink Solution The FGSW-1816HPS provides 2 extra Gigabit TP/SFP combo interfaces supporting 10/100/1000Base-T RJ-45 copper to connect with surveillance network devices such as NVR, Video Streaming Server or NAS to facilitate surveillance management. Or through these dual-speed fiber SFP slots, it can also connect with the 1000Base-SX/LX SFP (Small Form-factor Pluggable) fiber transceiver to uplink to backbone switch and monitoring center in long distance. The distance can be extended from 550m to 2km (multi-mode fiber), even going up to above 10/20/30/40/50/70/120km (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.

Physical Port

• 24-port 10/100BASE-TX RJ45 copper with 24-port IEEE 802.3at/af PoE injector
• 2-port 10/100/1000BASE-T Gigabit RJ45 copper
• 2 1000BASE-X mini-GBIC/SFP slots, shared with port-25 to port-26
• Reset button for system management

  Power over Ethernet

• Complies with IEEE 802.3at High Power over Ethernet End-span PSE
• Complies with IEEE 802.3af Power over Ethernet End-span PSE
• Up to 24 IEEE 802.3at / 802.3af devices powered
• Supports PoE Power up to 30.8 watts for each PoE port
• Detects powered device (PD) automatically
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m
• PoE Power Usage
• PoE Management
• Per port PoE function enable/disable
• PoE Port Power feeding priority
• Per PoE port power limit
• PD classification detection
• PoE power sequential

  Layer 2 Features

• Auto-MDI/MDI-X detection on each RJ45 port
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• Supports broadcast storm control
• Supports VLAN
• IEEE 802.1Q tag-based VLAN, up to 32 VLANs groups, out of 4095 VLAN IDs
• Port-based VLAN, up to 26 VLAN groups
• MTU VLAN (Multi-tenant Unit VLAN)
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Supports Spanning Tree Protocol
• STP, IEEE 802.1d Spanning Tree Protocol
• RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Provides port mirror (Many-to-1)

  Quality of Service

• 2 priority queues on all switch ports
• Traffic classification
• Port-based priority
• IEEE 802.1p-based priority
• IP TOS / DSCP-based priority
• TCP / UDP port-based QoS
• Strict priority and Weighted Round Robin (WRR) CoS policies

  Multicast

• Supports IGMP Snooping v1 and v2 (excluding IGMP Query feature)

  Security

• Physical port to MAC address binding
• TCP/UDP port number filter: Forwarding or discarding typical network applications
• Port mirroring to monitor the incoming or outgoing traffic on a particular port

  Management

• Switch Management Interfaces
• Web switch management
• SNMP v1 switch management
• Firmware upload/download via HTTP
• Hardware reset button for system reboot or resetting to factory default

   Cost-effective PoE+ Managed Switch for Small and Medium Networking Particularly designed for the growing popular IP surveillance applications, PLANET FGSW-2624HPS / FGSW-2624HPS4 802.3at PoE web smart switch is a surveillance switch with the central management of remote power control and IP camera monitoring. The FGSW-2624HPS / FGSW-2624HPS4 provides PoE functions along with 24 10/100BASE-TX ports featuring 30-watt 802.3at PoE+ with RJ45 copper interfaces and 2 Gigabit TP/SFP combo interfaces supporting high-speed transmission of surveillance images and videos. With a total power budget of up to 220 watts and 420 watts for different kinds of PoE applications, respectively, the FGSW-2624HPS and FGSW-2624HPS4 provide a quick, safe and cost-effective Power over Ethernet network solution for small businesses and enterprises.    Centralized Power Management for Security and Public Service PoE Applications To fulfill the needs of the high power consumption of PoE network applications, the FGSW-2624HPS / FGSW-2624HPS4 features the standard IEEE 802.3at Power over Ethernet Plus (PoE+) that combines up to 30 watts of power output and data per port over one cat5E/6 Ethernet cable. It is designed specifically to meet the demand of the high power consumption of network PDs (powered devices) such as IR, PTZ, speed dome cameras; and even box-type IP cameras with built-in fan and heater. Compliant with both 802.3at and 802.3af standards, the series allows more flexibility in power requirement for a variety of PDs, making installation costs affordable.    Intelligent LED Indicator for Real-time PoE Usage The FGSW-2624HPS / FGSW-2624HPS4 helps users to monitor the current status of PoE power usage easily and efficiently with its advanced LED indication. Called “PoE Power Usage” found on the front panel of the FGSW-2624HPS / FGSW-2624HPS4 Fast Ethernet PoE+ Switch, it has four orange LEDs indicating the range of the current PoE power usage.    Robust Layer 2 Features The FGSW-2624HPS / FGSW-2624HPS4 can be programmed for advanced switch management functions such as dynamic port link aggregation (LACP), Spanning Tree Protocol (STP), IGMP Snooping v1, v2, bandwidth control and L2/L4 security control. The FGSW-2624HPS / FGSW-2624HPS4 provides IEEE 802.1Q tagged VLAN, port-based VLAN and MTU VLAN. The VLAN groups allowed will be maximally up to 32. Via aggregation of supporting ports, the FGSW-2624HPS / FGSW-2624HPS4 allows the operation of a high-speed trunk combining multiple ports and supports fail-over as well.    Remote and Centralized Management For catering to the need of easy management and centralized SNMP application to monitor the status of the switch and traffic per port, the FGSW-2624HPS / FGSW-2624HPS4 provides friendly Web management interface for efficient network operation. With its built-in Web-based management, the FGSW-2624HPS / FGSW-2624HPS4 offers an easy-to-use, platform-independent management and configuration facility. It also supports standard Simple Network Management Protocol (SNMP) and can be monitored via any standard-based management software.    Flexible and Extendable Uplink Solution The FGSW-2624HPS / FGSW-2624HPS4 provides 2 extra Gigabit TP/SFP combo interfaces supporting 10/100/1000BASE-T RJ45 copper to connect with surveillance network devices such as NVR, Video Streaming Server or NAS to facilitate surveillance management. Or through these fiber SFP slots, it can also connect with the 1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber transceiver to uplink to backbone switch and monitoring center in long distance. The distance can be extended from 550m to 2km (multi-mode fiber), even going up to 10/20/30/40/50/70/120km (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.

• 24x10/100Mbps Fast Ethernet ports (unmanged)
• Supports auto MDI/MDI-X function
• Layer 2 Features
• Complies with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-TX Ethernet standard
• Supports powerful Green Ethernet to power saving
• Features Store-and-Forward mode with wire-speed filtering and forwarding rates
• Handles up to 1522 bytes packet size
• Complies with IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
• Integrated address look-up engine, support 8K absolute MAC addresses
• Automatic address learning and address aging
• Support CSMA/CD protocol
• Hardware Features
• 100~240V AC, 50~60Hz, 0.3A universal Power input
• FCC, CE class A compliant

  Power-Saving, High Performance Ethernet Networking In line with the energy-saving trend worldwide, PLANET delivers the new generation Green Networking Switch- FNSW-2401. The FNSW-2401 is a 24-port 10/100Base-TX Fast Ethernet Switch upgraded from earlier version and brings both benefits of energy saving and high performance. It is specially designed for SOHO, SMB and Workgroup users. The FNSW-2401 uses new engine that provides power saving up to 12% less energy but maintains high performance efficiently.   Energy Saving The FNSW-2401 incorporates advanced Green Networking technologies:

• Intelligent scales power based on cable length

  The intelligent scales power is an intelligent algorithm that actively determines the appropriate power level based on cable length. When connecting to the FNSW-2401 with Ethernet cable longer than 10m, a device can obtain maximum power saving because the FNSW-2401 would automatically detect the Ethernet cable length and reduce power usage. The connected device can substantially reduce overall power consumption, which makes a significant contribution to energy saving.   High Performance The high performance throughput (filtering/forwarding rate: 14,880 packets per second in 10Mbps, 148,800pps in 100Mbps) and dynamic shared memory buffer help the FNSW-2401 boost bandwidth, eliminate unnecessary traffic, and relieve congestion on your critical server path. The FNSW-2401 is the ideal choice to alleviate bottlenecks in client / server and peer-to-peer environments in a cost effective way.   Plug and Play The FNSW-2401provides users with high speed network connections. With its auto-negotiation capability, all the RJ-45/STP ports of the FNSW-2401 can be configured to speeds of 10/20Mbps or 100/200Mbps automatically. What's more the MDI/ MDIX auto-detection is for easy, plug and play connection, regardless of the cabling type, straight through or crossover.

• 10x 10/100BASE-TX Fast Ethernet RJ45 copper
• 8x IEEE 802.3at PoE+ Injector (Port-1 to Port-8)

  Power over Ethernet:

• Complies with IEEE 802.3at Power+ over Ethernet end-span PSE
• Up to 8 ports of IEEE 802.3af/802.3at devices powered
• Supports PoE power up to 30.8 watts for each PoE port
• Each port supports 55V DC power to PoE powered device
• 120-watt PoE budget
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m in standard mode with 250m in extend mode

  Switching:

• Hardware-based 10/100Mbps auto-negotiation and auto MDI/MDI-X
• Flow control for full duplex operation and back pressure for half duplex operation
• IEEE 802.1Q VLAN transparency
• Hardware DIP switch for Standard, VLAN and Extend mode selection; the Extend mode features 30-watt PoE transmit distance of 250m at speed of 10Mbps and VLAN isolation (Only for Port-1 to Port-8)
• Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP spoofing

  Hardware:

• 9-inch desktop size, 1U height, rack mountable
• LED indicators for system power, per port PoE ready and PoE activity, speed, Link/Act
• Fanless design
• Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az)

• 5x 10/100Mbps Fast Ethernet ports
• Complies with IEEE 802.3 10Base-T and IEEE 802.3u 100Base-TX Ethernet standards
• Supports auto MDI/MDI-X function
• Hardware-based 10/100Mbps, half / full duplex , flow control and auto-negotiation
• Features Store-and-Forward mode with wire-speed filtering and forwarding rates
• IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
• Integrated address look-up engine, supporting 2K absolute MAC addresses
• Handles up to 1536bytes packet

  High-speed 10/100Mbps Workgroup Switch PLANET Fast Ethernet Switch FSD-503 provides business and home users with a cost-effective integrated system of small-office / home-office networking. It is with compact-sized metal case design and just right for the network of 10 to 50 users.   Stable Fast Ethernet Switch Performance The FSD-503 also supports Store-and-Forward forwarding scheme to ensure low latency and high data integrity. The high performance throughput (filtering / forwarding rate: 14,880 packets per second in 10Mbps, and 148,800 packets per second in 100Mbps) and built-in packet buffer help the FSD-503 to boost bandwidth, eliminate unnecessary traffic, and relieve congestion on your critical server path. With an intelligent address recognition algorithm, the FSD-503 could recognize up to a 2K different MAC addresses and provide 1Gbps switching capacity, which makes the FSD-503 the best in wire-speed packet transfer performance without risk of packet loss.   Flexible Desktop Size Design The FSD-503 is a fancy-shaped standard metal model that nicely fits in a space-limited environment. With concepts of "easy to install and use", "compact sized design", and "simple troubleshooting", the FSD-503 provides cost-conscious business and home users with a flexible yet cost-effective SOHO / Home networking.    Power Energy Saving With one power ON/OFF button designed on the rear panel of the FSD-503, it can help users to reduce unnecessary power energy loss while the FSD-503 operation is OFF.   Plug & Play and Easy Installation All RJ-45 copper interfaces in the FSD-503 support 10/100Mbps auto-negotiation for optimal speed detection through RJ-45 Category 5/5e cables. Supporting standard for auto-MDI/MDI-X can detect the type of connection to any Ethernet device without requiring special straight-through or crossover cables. The Flow Control function allows the FSD-503 to support routers and servers for direct connection to this switch with fast and reliable data transfer.

• 6x 10/100Mbps Fast Ethernet ports
• 4x ports supporting 52V DC power to PoE powered device

  Power over Ethernet:

• Complies with IEEE 802.3af/at Power over Ethernet end-span
• Up to 4 IEEE 802.3af/2 IEEE 802.3at devices powered
• Supports PoE power up to 30 watts for each PoE port
• 60-watt PoE budget
• Hardware DIP switch for "Standard" and "Extend" mode selection; the "Extend" mode features 30-watt PoE transmit distance of 250m at speed of 10Mbps and VLAN isolation
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m in the standard mode

  Switching:

• Hardware-based 10/100Mbps auto-negotiation and auto MDI/MDI-X
• Flow control for full duplex operation and back pressure for half duplex operation
• 1536bytes packet size
• Integrates address look-up engine, supporting 2K absolute MAC addresses
• Automatic address learning and address aging
• Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP spoofing

  Hardware:

• Desktop palm size
• LED indicators for PoE ready/activity and LINK/ACT
• Supports contact discharge of ±4KV DC and air discharge of ±6KV DC for Ethernet ESD protection
• Supports ±4KV surge immunity
• Internal AC power supply

 

• 8x 10/100Mbps Fast Ethernet ports
• Complies with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-TX Ethernet standards
• Hardware-based 10/100Mbps, half / full duplex , flow control and auto-negotiation
• Features Store-and-Forward mode with wire-speed filtering and forwarding rates
• IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
• Integrated address look-up engine, supporting 1K absolute MAC addresses
• Handles up to 1536bytes packet
• Automatic address learning and address aging
• Supports CSMA/CD protocol

  High-speed 10/100Mbps Workgroup Switch PLANET Fast Ethernet Switch FSD-803 provides business and home users with a cost-effective integrated system of small-office / home-office networking. It is with compact-sized metal case design and just right for the network of 10 to 50 users.   Stable Fast Ethernet Switch Performance The FSD-803 also supports Store-and-Forward forwarding scheme to ensure low latency and high data integrity. The high performance throughput (filtering / forwarding rate: 14,880 packets per second in 10Mbps, and 148,800 packets per second in 100Mbps) and 448K bit packet buffer help the FSD-803 to boost bandwidth, eliminate unnecessary traffic, and relieve congestion on your critical server path. With an intelligent address recognition algorithm, the FSD-803 could recognize up to a 1K different MAC address and provide 1.6Gbps switching capacity, which makes the FSD-803 offer wire-speed packets transfer performance without risk of packet loss.   Flexible Desktop Size Design The FSD-803 is the fancy-shaped standard metal model to fit into space-limited environment. With concepts of "Easy to install and use", "Compact sized design", and "Simple troubleshooting", the FSD-803 provides cost-conscious business and home users with the foundation from an integrated system of small-office / home-office networking.    Power Energy Saving With one power ON/OFF button designed on the rear panel of the FSD-803, it can help users to reduce unnecessary power energy loss while the FSD-803 operation is OFF.   Plug & Play and Easy Installation All RJ-45 copper interfaces in the FSD-803 support 10/100Mbps auto-negotiation for optimal speed detection through RJ-45 Category 5/5e cables. Supporting standard for auto-MDI/MDI-X can detect the type of connection to any Ethernet device without requiring special straight or crossover cables. The Flow Control function allows the FSD-803 to support routers and servers for direct connection to this switch with fast and reliable data transfer.

• Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u, 100BASE-TX and 100BASE-FX Ethernet standards
• One 10/100BASE-TX port with RJ45 connector
• One 100BASE-FX port with ST/SC/WDM connector supporting multi-mode or single-mode fiber optic cable
• Auto-negotiation and auto-MDI / MDI-X for 10/100BASE-TX port
• Back-pressure and IEEE 802.3x compliant flow control and full wire-speed forwarding rate
• Link Loss Return (LLR) switch on each fiber optic is to aid in troubleshooting remote network connections
• Link Loss Carry Forward (LLCF) works with LLR in diagnosing network connections

Distance Extended with Fiber Optic Cable PLANET FST-80x Smart Media Converter series provides media conversion between 10/100BASE-TX and 100BASE-FX interfaces, such as multi-mode ST/SC connectors (2km), single-mode SC connector (15/35/50km) and single fiber connector using the wavelength-division multiplexing (WDM) technology (20/60km) to enable to extend links over long distances using fiber optic cable.    Enhanced Smart Management Features The FST-80x series provides auto MDI/MDI-X on their TP port and store-and-forward mechanism to eliminate faulty packets. Use the DIP switch from the FST-80x to configure the available smart functions, such as the half/full duplex, auto-negotiation / force and 10/100Mbps options for TP and fiber interfaces. Besides, the Link Loss Return (LLR) and Link Loss Carry Forward (LLCF) functions can immediately alarm network administrator once there is a media link issue, thus helping to monitor the status of the entire network.    Easy Installation The FST-80x series can be connected easily and cost-effectively as these smart media converters can be used as a standalone unit when powered on by its DC adapter, or used as a slide-in module connected to PLANET 19-inch, 16-slot web smart/managed media converter chassis (MC-1600MR/MC-1600MR48 and MC-1610MR/MC-1610MR48). When working with the web smart/managed media converter chassis, the status of the FST-80x can be monitored via the local RS-232 console and remote web interface.

• Complies with IEEE 802.3, IEEE 802.3u 10 / 100Base-TX and 100Base-FX
• IEEE 802.3x full-duplex flow-control, back-pressure in Half-duplex eliminate packet loss
• TS-1000 / OAM function built-in, the device can be remotely monitored with port link status
• Dual 100Base-FX SFP fiber optic
• One 10 / 100Base-TX copper
• Auto-negotiation for 100Base-TX half-duplex or 100Base-T full-duplex
• Supports auto MDI / MDI-X function
• Supports maximum frame size up to 2046Kbytes
• Link status auto-detect and redundant on dual ports with the same connector type
• Only primary port is active at a time, the backup port is blocked
• While primary port link fail occurrences, the traffic will swap to backup port automatically
• Once the primary port status is back to linkup, the traffic will swap from backup port to primary port
• Hardware redundant swaps less than 10 ms

  PLANET FT-1205A is a 3-port Redundant Media Converter which supports conversion between 10 / 100Base-TX and 100Base-FX network. The difference with the other one-port channel media converter is the Redundant Media Converter. It is designed for critical networks that require fibers or copper links to automatically recover less than 10ms, such as ISPs, telecoms, hospitals, banks and enterprises.   Via the built-in DIP switches, the converter can be configured as 3-port Ethernet switch or 2-port redundant media converter. With the 3-port switch mode, it can operate Store-and-Forward mechanism with high performance, and it can also prevent packet loss via IEEE 802.3x flow control (full-duplex) and back pressure (half-duplex).   With the 2-port redundant mode, it provides less than 10ms redundancy of link for highly critical Ethernet applications. The redundant mode supports auto-recover function. If the destination port of a packet is link-down, it forwards the packet to the other port of the backup pair.   The SFP slot supports single-mode, multi-mode and WDM small-form factory type transceiver modules for various applications. The FT-1205A is with high reliability and flexibility to extend the distance up to 2km, 20km or longer. It depends on the 100Base-FX SFP transceiver modules. The Ethernet signal that allows two types of segments to connect easily, efficiently and inexpensively.   The converters can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter Chassis, MC-700, MC-1500, MC-1500R and MC-1500R48. As to the other PLANET media converters (FT series), they're hot swappable in MC chassis.