SHOP

Verkabelung Elektriker

(12 Treffer)
Hersteller, PLANET - GS-4210-24P2S
24-Port Managed 802.3at POE+ Gbit Ethernet + 2-Port SFP
Preis auf Anfrage
  • 24-port 10/100/1000Base-T Gigabit RJ-45 copper
  • 2 100/1000Base-X mini-GBIC/SFP slots
  • RJ-45 console interface for switch basic management and setup
  • Reset button for system factory default and reboot
  • Complies with IEEE 802.3at High Power over Ethernet
  • Complies with IEEE 802.3af Power over Ethernet
  • Up to 24 ports of IEEE 802.3af / 802.3at devices powered
  • Supports PoE Power up to 30.8 watts for each PoE port
  • 300-watt PoE budget
  • Auto detects powered device (PD)
  • Circuit protection prevents power interference between ports
  • Remote power feeding up to 100m
  • PoE Management
- Total PoE power budget control - Per port PoE function enable/disable - PoE Port Power feeding priority - Per PoE port power limitation - PoE delay - PD classification detection
  • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
  • High performance Store and Forward architecture, runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
  • Supports VLAN
- IEEE 802.1Q tagged VLAN, up to 256 VLAN groups, out of 4094 VLAN IDs - Protocol VLAN
  • Supports Spanning Tree Protocol
- STP (Spanning Tree Protocol) - RSTP (Rapid Spanning Tree Protocol) - MSTP (Multiple Spanning Tree Protocol) - STP BPDU Guard, BPDU Filtering and BPDU Forwarding
  • Supports Link Aggregation
- IEEE 802.3ad Link Aggregation Control Protocol (LACP) - Maximum 8 LACP groups, up to 16 ports per LACP group - Cisco ether-channel (Static Trunk) - Maximum 8 trunk groups, up to 8 ports per trunk group
  • Provides port mirror (many-to-1)
  • Ingress / Egress Rate Limit per port bandwidth control
  • Storm Control support
- Broadcast / Unknown-Unicast / Unknown-Multicast
  • Traffic classification
- IEEE 802.1p CoS - DSCP / IP Precedence of IPv4 / IPv6 packets
  • Strict priority and Weighted Round Robin (WRR) CoS policies
  • Supports IGMP Snooping v2 and v3
  • IGMP Querier mode support
  • IGMP Snooping port filtering
  • Up to 256 multicast groups
  • Authentication
- IEEE 802.1X port-based network access authentication - Built-in RADIUS client to co-operate with the RADIUS servers - DHCP Option 82 - RADIUS / TACACS+ login user access authentication
  • Access Control List
- IPv4 IP-based ACL - IPv4 IP-based ACE - MAC-based ACL - MAC-based ACE
  • MAC Security
- Static MAC - MAC Filtering
  • Port Security for Source MAC address entries filtering
  • DHCP Snooping to filter distrusted DHCP messages
  • Switch Management Interface
- Local Command Line Interface - Web switch management - Telnet Command Line Interface - SNMP v1, v2c and v3 - HTTPs secure access
  • Built-in Trivial File Transfer Protocol (TFTP) client
  • Static and DHCP for IP address assignment
  • System Maintenance
- Firmware upload / download via HTTP / TFTP - Configuration upload / download through HTTP / TFTP - Dual Images - Hardware reset button for system reboot or reset to factory default
  • SNTP Network Time Protocol
  • Link Layer Discovery Protocol (LLDP) Protocol and LLDP-MED
  • SNMP trap for interface Link Up and Link Down notification
  • Event message logging to remote Syslog server
  • Four RMON groups (history, statistics, alarms and events)
  • PLANET Smart Discovery Utility
  Cost-Optimized Managed PoE+ Switch for Small and Medium Businesses PLANET GS-4210-24P2S is an ideal Gigabit PoE Switch which provides cost-effective advantage to local area network and is widely accepted in the SMB office network. It offers intelligent Layer 2 data packet switching and management functions, friendly web user interface and stable operation. The model complies with IEEE 802.3at Power over Ethernet Plus (PoE+) at an affordable price. The GS-4210-24P2S is equipped with 24 10/100/1000Base-T Gigabit Ethernet ports and 2 100/1000Base-X SFP interfaces with inner power system. Its 24 Gigabit Ethernet ports integrated with 802.3at PoE+ injector function on all ports. It offers a rack-mountable, affordable, safe and reliable power solution for SMBs deploying Power over Ethernet networks, or requiring enhanced data security and network traffic management.    IEEE 802.3at/af Compliant Power Source Switch The PoE in-line power following the IEEE 802.3at/af standard makes the GS-4210-24P2S able to deliver Gigabit speed data and up to 30 watts of power per port to 24 PoE compliant powered devices (PDs) with a combined power output budget of up to 300 watts. The GS-4210-24P2S provides more flexibility in power requirement for all kinds of PDs with affordable installation costs.    Robust Layer 2 Features The GS-4210-24P2S can be programmed for advanced switch management functions such as dynamic port link aggregation, 802.1Q VLAN, Spanning Tree protocol (STP), Rapid Spanning Tree protocol (RSTP) and Multiple Spanning Tree protocol (MSTP), IGMP Querier and IGMP Snooping. Via aggregation of supporting ports, the GS-4210-24P2S allows the operation of a high-speed trunk to combine with multiple ports such as a 32Gbps fat pipe and supports fail-over as well. The Link Layer Discovery Protocol (LLDP) feature is also included and used to discover basic information about neighboring devices on the local broadcast domain.   Efficient Traffic Control The GS-4210-24P2S is loaded with robust QoS features and powerful traffic management to enhance services to business-class data, voice, and video solutions. The functionality includes broadcast / multicast / unicast storm control, per port bandwidth control, 802.1p / CoS / IP DSCP QoS priority and remarking. It guarantees the best performance at VoIP and video stream transmission, and empowers the enterprises to take full advantages of the limited network resources.   Enhanced and Secure Management For efficient management, the GS-4210-24P2S is equipped with console, Web, Telnet and SNMP management interfaces. With the built-in Web-based management interface, the GS-4210-24P2S offers an easy-to-use, platform-independent management and configuration facility. By supporting standard Simple Network Management Protocol (SNMP), the switch can be managed via any standard management software. For text-based management, the switch can be accessed via Telnet and the console port. Moreover, the GS-4210-24P2S offers secure remote management by supporting HTTPS and SNMPv3 connections which encrypt the packet content at each session.   Powerful Security PLANET GS-4210-24P2S offers comprehensive Layer 2 to Layer 4 Access Control List (ACL) for enforcing security to the edge. It can be used to restrict network access by denying packets based on source and destination IP address, TCP/UDP ports or defined typical network applications. Its protection mechanism also comprises 802.1X port-based authentication, which can be deployed with RADIUS to ensure the port level security and block illegal users. The Port Security allows limiting the number of users on a given port. The network administrators can now construct highly-secured corporate networks with considerably less time and effort than before.   Flexible Extension Solution The two mini-GBIC slots built in the GS-4210-24P2S are compatible with the 100Base-FX / 1000Base-SX/LX SFP (Small Form-factor Pluggable) fiber transceiver to uplink to backbone switch and monitor center in long distance. The distance can be extended from 550 meters to 2km (multi-mode fiber) up to above 10/20/30/40/50/60/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.
Verfügbarkeit:
nicht lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - GS-4210-24T2S
24-Port Layer 2 Managed Gigabit Switch mit SFP
Preis auf Anfrage
  • 24-port 10/100/1000BASE-T Gigabit RJ45 copper
  • 2x100/1000BASE-X mini-GBIC/SFP slots
  • RJ45 console interface for switch basic management and setup
  • Reset button for system factory default
  • fanless
  Cost-Optimized Managed Switch for Small and Medium Businesses PLANET GS-4210-24T2S is an ideal Gigabit Switch which provides cost-effective advantage to local area network and is widely accepted in the SMB office network. It offers intelligent Layer 2 data packet switching and management functions, friendly web user interface and stable operation. Besides the hot IPv6 / IPv4 management and abundant L2 / L4 switching functions, the GS-4210-24T2S comes with fanless feature and green technology to provide a quiet, energy-saving, high-speed and reliable office network environment. The GS-4210-24T2S is equipped with 24 10/100/1000BASE-T Gigabit Ethernet ports and 2 additional 100/1000BASE-X SFP interfaces with inner power system. It offers a rack-mountable, affordable, safe and reliable Gigabit network switch solution for SMBs deploying networks, or requiring enhanced data security and network traffic management.    Robust Layer 2 Features The GS-4210-24T2S can be programmed for advanced switch management functions such as dynamic port link aggregation, 802.1Q VLAN and Q-in-Q VLAN, Multiple Spanning Tree protocol (MSTP), Loop and BPDU Guard, IGMP Snooping, and MLD Snooping. Via the link aggregation, the GS-4210-24T2S allows the operation of a high-speed trunk to combine with multiple ports such as a 16Gbps fat pipe, and supports fail-over as well. Also, the Link Layer Discovery Protocol (LLDP) is the Layer 2 protocol included to help discover basic information about neighboring devices on the local broadcast domain.    Efficient Traffic Control The GS-4210-24T2S is loaded with robust QoS features and powerful traffic management to enhance services to business-class data, voice, and video solutions. The functionality includes broadcast / multicast / unicast storm control, per port bandwidth control, 802.1p / CoS / IP DSCP QoS priority and remarking. It guarantees the best performance at VoIP and video stream transmission, and empowers the enterprises to take full advantage of the limited network resources.    Enhanced and Secure Management For efficient management, the GS-4210-24T2S is equipped with console, Web, Telnet and SNMP management interfaces. With the built-in Web-based management interface, the GS-4210-24T2S offers an easy-to-use, platform-independent management and configuration facility. By supporting standard Simple Network Management Protocol (SNMP), the switch can be managed via any standard management software. For text-based management, the switch can be accessed via Telnet and the console port. Moreover, the GS-4210-24T2S offers secure remote management by supporting HTTPS and SNMP v3 connections which encrypt the packet content at each session.    Powerful Security PLANET GS-4210-24T2S offers comprehensive IPv4 / IPv6 Layer 2 to Layer 4 Access Control List (ACL) for enforcing security to the edge. It can be used to restrict network access by denying packets based on source and destination IP address, TCP/UDP ports or defined typical network applications. Its protection mechanism also comprises 802.1X port-based authentication, which can be deployed with RADIUS to ensure the port level security and block illegal users. With the protected port function, communication between edge ports can be prevented to guarantee user privacy. Furthermore, port security function allows limiting the number of network devices on a given port.    Advanced Network Security The GS-4210-24T2S also provides DHCP snooping, IP source guard and dynamic ARP inspection functions to prevent IP snooping from attack and discard ARP packets with invalid MAC address. The network administrators can now construct highly-secured corporate networks with considerably less time and effort than before.    Flexible Extension Solution The two mini-GBIC slots built in the GS-4210-24T2S are compatible with the 100BASE-FX / 1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber transceiver to uplink to backbone switch and monitor center in long distance. The distance can be extended from 550 meters to 2km (multi-mode fiber) up to above 10/20/30/40/50/60/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.    Fanless Design Adopting the latest chip process and green technology, the GS-4210-24T2S successfully reduces substantial power consumption with the fanless and noiseless design collocating with the effective cooler. Therefore, the GS-4210-24T2S is able to operate stably and quietly in any environment without affecting its performance.
Verfügbarkeit:
lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - GS-4210-24T4S(R)
24-Port Layer 2 Managed Gigabit Switch mit 4x SFP, redundant Power optional
Preis auf Anfrage
  • 24-Port 10/100/1000BASE-T Gigabit RJ45 copper
  • 4 100/1000BASE-X mini-GBIC/SFP slots
  • RJ45 console interface for switch basic management and setup
  • Reset button for system factory default
  Switching:
  • Hardware-based 10/100Mbps, half/full duplex and 1000Mbps full duplex mode, flow control and auto-negotiation, and auto MDI/MDI-X
  • Features Store-and-Forward mode with wire-speed filtering and forwarding rates
  • IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
  • 10K jumbo frame
  • Automatic address learning and address aging
  • Supports CSMA/CD protocol
  Layer 2 Features:
  • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
  • High performance Store and Forward architecture, broadcast storm control, runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
  • Supports VLAN
    • IEEE 802.1Q tagged VLAN
    • Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
    • Protocol VLAN
    • Voice VLAN
    • Private VLAN
    • Management VLAN
    • GVRP
  • Supports Spanning Tree Protocol
    • STP (Spanning Tree Protocol)
    • RSTP (Rapid Spanning Tree Protocol)
    • MSTP (Multiple Spanning Tree Protocol)
    • STP BPDU Guard, BPDU Filtering and BPDU Forwarding
  • Supports Link Aggregation
    • IEEE 802.3ad Link Aggregation Control Protocol (LACP)
    • Cisco ether-channel (Static Trunk)
    • Maximum 8 trunk groups, up to 8 ports per trunk group
  • Provides port mirror (many-to-1)
  • Loop protection to avoid broadcast loops
  Quality of Service:
  • Ingress/Egress Rate Limit per port bandwidth control
  • Storm Control support
    • Broadcast/Unknown-Unicast/Unknown-Multicast
  • Storm Control support
    • Broadcast/Unknown-Unicast/Unknown-Multicast
  • Traffic classification
    • IEEE 802.1p CoS
    • TOS / DSCP/IP Precedence of IPv4/IPv6 packets
  • Strict priority and Weighted Round Robin (WRR) CoS policies
  Multicast:
  • Supports IPv4 IGMP snooping v2 and v3
  • Supports IPv6 MLD snooping v1, v2
  • IGMP querier mode support
  • IGMP snooping port filtering
  • MLD snooping port filtering
  Security:
  • Authentication
    • IEEE 802.1X Port-based network access authentication
    • Built-in RADIUS client to co-operate with the RADIUS servers
    • DHCP Option 82
    • RADIUS/TACACS+ login user access authentication
  • Access Control List
    • IPv4/IPv6 IP-based ACL
    • IPv4/IPv6 IP-based ACE
    • MAC-based ACL
    • MAC-based ACE
  • MAC Security
    • Static MAC
    • MAC Filtering
  • Port Security for Source MAC address entries filtering
  • DHCP Snooping to filter distrusted DHCP messages
  • Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
  • IP Source Guard prevents IP spoofing attacks
  • DoS Attack Prevention
  • SSH/SSL
  Management:
  • IPv4 and IPv6 dual stack management
  • Switch Management Interface
    • Web switch management
    • Console/Telnet Command Line Interface
    • SNMP v1 and v2c switch management
    • SSHv2, TLSv1.2 and SNMP v3 secure access
  • SNMP Management
    • Four RMON groups (history, statistics, alarms, and events)
    • SNMP trap for interface Link Up and Link Down notification
  • User Privilege Levels Control
  • Built-in Trivial File Transfer Protocol (TFTP) client
  • BOOTP and DHCP for IP address assignment
  • System Maintenance
    • Firmware upload/download via HTTP/TFTP
    • Configuration upload / download through Web interface
    • Dual Images
    • Hardware reset button for system reboot or reset to factory default
  • SNTP Network Time Protocol
  • Network Diagnostic
    • ICMPv6/ICMPv4 Remote Ping
    • Cable Diagnostics
  • Link Layer Discovery Protocol (LLDP) Protocol and LLDP-MED
  • Event message logging to remote Syslog server
  • PLANET NMS System and Smart Discovery Utility for deployment management
Redundant Power System (GS-4210-24T4SR):
  • Redundant 100~240V AC/36-72V DC dual power
  • Active-active redundant power failure protection
  • Backup of catastrophic power failure on one supply
  • Fault tolerance and resilience

Verfügbarkeit:
nicht lagernd
Login für mehr Info
Varianten: 2
mehr Informationen
zu Favoriten
Hersteller, PLANET - GSD-1008HP
8-Port 10/100/1000Mbps 802.3at PoE + 2-Port 10/100/1000T Desktop Switch, 120W
Preis auf Anfrage
Rack Mount Kit ist enthalten!
  • 10-port 10/100/1000BASE-T Gigabit Ethernet RJ45 copper
  • 8-port IEEE 802.3at PoE+ Injector (Port-1 to Port-8)
  Power over Ethernet
  • Complies with IEEE 802.3at Power+ over Ethernet end-span PSE
  • Up to 8 ports of IEEE 802.3af/802.3at devices powered
  • Supports PoE power up to 30.8 watts for each PoE port
  • Each port supports 55V DC power to PoE powered device
  • 120-watt PoE budget
  • Auto detects powered device (PD)
  • Circuit protection prevents power interference between ports
  • Remote power feeding up to 100m in standard mode with 250m in extended mode
  Switching
  • Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/MDI-X
  • Flow control for full duplex operation and back pressure for half duplex operation
  • IEEE 802.1Q VLAN transparency
  • Hardware DIP switch for Standard, VLAN and Extend mode selection; the Extend mode features 30-watt PoE transmit distance of 250m at speed of 10Mbps and VLAN isolation (Only for Port-1 to Port-8)
  • Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP spoofing
  Hardware
  • 9-inch desktop size, 1U height, rack mountable
  • LED indicators for system power, per port PoE ready and PoE activity, speed, Link/Act
  • Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az)
Verfügbarkeit:
lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - GSD-503
5-Port 10/100/1000Mbps Gigabit Ethernet Switch (External
Preis auf Anfrage
  • 5-Port 10/100/1000Mbps Gigabit Ethernet
  • Complies with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T
  • Supports auto MDI/MDI-X function
  • Hardware based 10/100Mbps, half / full duplex and 1000Mbps full duplex mode, flow control and auto-negotiation
  • Features Store-and-Forward mode with wire-speed filtering and forwarding rates
  • IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
  • Integrated address look-up engine, supporting 2K absolute MAC addresses
  • 9K Jumbo packet size
  • Power saving ability for Green networking
  • Automatic address learning and address aging
  • Supports CSMA/CD protocol
  • Made of metal, desktop size and wall-mount design
  • LED indicators for system power, per port 1000 & Link / Act
  • 5V DC, 1A external power adapter
  • FCC, CE Class B compliant
  Optimal Solution for Energy Saving and Gigabit High Performance PLANET Green Networking Switch - GSD-503 is an ideal solution in line with the energy-saving trend worldwide. The GSD-503 is a 5-port Gigabit Ethernet Switch bringing both benefits of energy saving and Gigabit wire speed performance. It is specially designed for home networking, SOHOs and enterprises.   Energy Saving The GSD-503 incorporates two advanced Green Networking technologies and is able to provide power saving up to 40% less energy but maintains high performance efficiently. (1) Hibernation Link Down power saving The Hibernation Link Down power saving goes beyond IEEE specifications to automatically lower power for a given port when it is not linked. With the Hibernation Link Down power saving technology, the GSD-503 will automatically adjust power usage of the ports that are shut down or not connected to network device. (2) Intelligent scales power based on cable length Intelligent scales power, the other technology adopted, is an intelligent algorithm that actively determines the appropriate power level based on cable length. When the GSD-503 is connected with Ethernet cable shorter than 20m, a device can obtain maximum power saving because the GSD-503 would automatically detect the Ethernet cable length and diminish power usage. The connected device can substantially reduce the overall power consumption, which makes a significant contribution to energy saving.      Leading Home, SOHO and Workgroup Users to High-speed Networking Generation The GSD-503 is designed with modern metal compact housing and easy for deployment of high speed Gigabit networking in home or SOHO applications. Providing 10Gbps internal switching fabric, the GSD-503 can handle an extremely large amount of data in a secure topology linking to a backbone or high capacity servers. The GSD-503 provides 2K MAC address table, and offers wire-speed packet transfer performance without risk of packet loss. The high data throughput of the device makes it ideal for most Gigabit environments, especially for the network to be upgraded to a Gigabit environment.   Plug & Play All RJ-45 copper interfaces of the GSD-503 support 10/100/1000Mbps auto-negotiation for optimal speed detection through RJ-45 Category 5, 5e or 6 cables. They support standard auto-MDI/MDI-X feature which can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.  
Verfügbarkeit:
lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - GSD-803
8-Port 10/100/1000Mbps Gigabit Ethernet Switch, External Power
Preis auf Anfrage
  • 8x10/100/1000Mbps Gigabit Ethernet ports
  • Complies with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T
  • Supports auto MDI/MDI-X function
  • Hardware based 10/100Mbps, half / full duplex and 1000Mbps full duplex mode, flow control and auto-negotiation
  • Features Store-and-Forward mode with wire-speed filtering and forwarding rates
  • IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
  • Integrated address look-up engine, supporting 8K absolute MAC addresses
  • 9K Jumbo packet size
  • Power saving ability for Green networking
  • Automatic address learning and address aging
  • Supports CSMA/CD protocol
  • Made of metal, desktop size and wall-mount design
  • LED indicators for system power, per port 1000 & Link / Act
  • 5V DC, 1A external power adapter
  • FCC, CE Class B compliant
  Optimal Solution for Energy Saving and Gigabit High Performance PLANET Green Networking Switch-GSD-803 is an ideal solution in line with the energy-saving trend worldwide. The GSD-803 is an 8-port Gigabit Ethernet Switch bringing both benefits of energy saving and Gigabit wire speed performance. It is specially designed for home networking, SOHOs and enterprises.   Energy Saving The GSD-803 incorporates two advanced Green Networking technologies and is able to provide power saving up to 40% less energy but maintains high performance efficiently. (1) Hibernation Link Down power saving The Hibernation Link Down power saving goes beyond IEEE specifications to automatically lower power for a given port when it is not linked. With the Hibernation Link Down power saving technology, the GSD-803 will automatically adjust power usage of the ports that are shut down or not connected to network device. (2) Intelligent scales power based on cable length Intelligent scales power, the other technology adopted, is an intelligent algorithm that actively determines the appropriate power level based on cable length. When the GSD-803 is connected with Ethernet cable shorter than 20m, a device can obtain maximum power saving because the GSD-803 would automatically detect the Ethernet cable length and diminish power usage. The connected device can substantially reduce the overall power consumption, which makes a significant contribution to energy saving.      Leading Home, SOHO and Workgroup Users to High-speed Networking Generation The GSD-803 is designed with modern metal compact housing and easy for deployment of high speed Gigabit networking in home or SOHO applications. Providing 16Gbps internal switching fabric, the GSD-803 can handle an extremely large amount of data in a secure topology linking to a backbone or high capacity servers. The GSD-803 provides 8K MAC address table, and wire-speed packet transfer performance without risk of packet loss. The high data throughput of the device makes it ideal for most Gigabit environments, especially for the network to be upgraded to a Gigabit environment.   Plug & Play All RJ-45 copper interfaces of the GSD-803 support 10/100/1000Mbps auto-negotiation for optimal speed detection through RJ-45 Category 5, 5e or 6 cables. They support standard auto-MDI/MDI-X feature which can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.  
Verfügbarkeit:
lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - GSW-2401
24-Port 10/100/1000Mbps Unmanaged Gbit Ethernet Switch
Preis auf Anfrage
• Complies with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T Ethernet standard • 24x 10/100/1000Mbps Gigabit Ethernet ports • Features Store-and-Forward mode with wire-speed filtering and forwarding rates • Hardware based 10/100Mbps, half / full duplex and 1000Mbps full duplex mode, flow control and auto-negotiation • IEEE 802.3x flow control for full duplex operation and backpressure for half duplex operation • Integrated address look-up engine, support 8K absolute MAC addresses • 9K Jumbo packet support • Automatic address learning and address aging • Supports auto MDI/MDI-X function • Supports CSMA / CD protocol • 100-240V AC, 0.6A, 50/60Hz universal Power input • FCC, CE class A compliant   Cost-effective Gigabit Switch for Enterprise Backbone and Data Center Networking PLANET GSW-2401 Gigabit Ethernet Switch provides 24 RJ-45 10/100/1000Mbps ports for high-speed network connectivity. It can automatically identify and determine the correct transmission speed and half / full duplex mode of the attached devices with its 24 Gigabit ports that support 9K jumbo frame feature. Therefore, the GSW-2401 can handle an extremely large amount of data transmission in a secure topology linking to a backbone or high-power servers.   High Performance The GSW-2401 provides high performance switch architecture that is capable of providing the non-blocking switch fabric and wire-speed throughput as high as 48Gbps, which greatly simplifies the tasks of upgrading the LAN for catering to increasing bandwidth demands. Besides, the Flow Control function of the GSW-2401 enables routers and servers directly connect to the Switch for fast and reliable data transfer.   All RJ-45 copper interfaces of the GSW-2401 support 10/100/1000Mbps auto-negotiation for optimal speed detection through RJ-45 Category 6, 5 or 5e cables. It also supports standard for auto-MDI/MDI-X that can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.   Excellent Traffic Transmission The GSW-2401 supports Store-and-Forward forwarding scheme to ensure low latency and high data integrity, which eliminates unnecessary traffic and relieves congestion on critical network paths. With an intelligent address recognition algorithm, the GSW-2401 could recognize up to 8K different MAC address. The high data throughput and 48Gbps internal switching fabric makes it ideal for most Gigabit network environments, especially helpful for the network upgrading to a Gigabit environment.   Fanless Design The GSW-2401 successfully reduces substantial power consumption with the fanless and noiseless design collocating with the effective cooler. Therefore, the GSW-2401 is able to operate stably and quietly in any environment without affecting its performance.  
Verfügbarkeit:
lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - IGS-10020HPT
Industrial 8-Port Gbit PoE(at) + 2Port SFP managed Switch
Preis auf Anfrage
  • 8x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with IEEE 802.3at PoE+ Injector
  • 2x 100/1000BASE-X mini-GBIC/SFP slots for SFP type auto detection
  • One RJ45 console interface for basic management and setup
  Power over Ethernet
  • Complies with IEEE 802.3at Power over Ethernet Plus/end-span PSE
  • Up to 8 IEEE 802.3af/802.3at devices powered
  • Supports PoE power up to 36 watts for each PoE port
  • Auto detects powered device (PD)
  • Circuit protection prevents power interference between ports
  • Remote power feeding up to 100m
  • PoE management features
- IEEE 802.3af and IEEE 802.3at mode switch control - Total PoE power budget control - Per port PoE function enable/disable - PoE admin-mode control - PoE port power feeding priority - Per PoE port power limit - PD classification detection - Temperature threshold control - PoE usage threshold control - PD alive check - PoE schedule   Industrial Case & Installation
  • IP30 aluminum case protection
  • DIN rail and wall-mount design
  • 48V DC, redundant power with polarity reverse protect function
  • Supports EFT protection of 6000 VDC for power line
  • Supports 6000 VDC Ethernet ESD protection
  • -40 to 75 degrees C operating temperature
  Digital Input & Digital Output
  • 2 Digital Input (DI)
  • 2 Digital Output (DO)
  • Integrate sensors into auto alarm system
  • Transfer alarm to IP network via email and SNMP trap
  Layer 2 Features
  • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
  • High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
  • Storm Control support
- Broadcast/Multicast/Unicast
  • Supports VLAN
- IEEE 802.1Q tagged VLAN - Up to 255 VLANs groups, out of 4094 VLAN IDs - Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad) - Private VLAN Edge (PVE) - Protocol-based VLAN - MAC-based VLAN - Voice VLAN
  • Supports Spanning Tree Protocol
- IEEE 802.1D Spanning Tree Protocol (STP) - IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) - IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN (MSTP) - BPDU Guard
  • Supports Link Aggregation
- 802.3ad Link Aggregation Control Protocol (LACP) - Cisco ether-channel (static trunk) - Maximum 5 trunk groups with 8 ports per trunk group - Up to 16Gbps bandwidth (duplex mode)
  • Provides port mirror (1-to-1)
  • Port mirroring to monitor the incoming or outgoing traffic on a particular port
  • Loop protection to avoid broadcast loops
  • Supports ERPS (Ethernet Ring Protection Switching)
  Layer 3 IP Routing Features
  • Supports maximum 32 software static routes and route summarization
  Quality of Service
  • Ingress Shaper and Egress Rate Limit per port bandwidth control
  • 8 priority queues on all switch ports
  • Traffic classification
- IEEE 802.1p CoS - IP TOS/DSCP/IP precedence - IP TCP/UDP port number - Typical network application
  • Strict priority and Weighted Round Robin (WRR) CoS policies
  • Supports QoS and In/Out bandwidth control on each port
  • Traffic-policing policies on the switch port
  • DSCP remarking
  Multicast
  • Supports IGMP snooping v1, v2 and v3
  • Supports MLD snooping v1 and v2
  • Querier mode support
  • IGMP snooping port filtering
  • MLD snooping port filtering
  • MVR (Multicast VLAN Registration)
  Security
  • IEEE 802.1x Port-based/MAC-based network access authentication
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • TACACS+ login users access authentication
  • RADIUS/TACACS+ users access authentication
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List
  • Source MAC/IP address binding
  • DHCP snooping to filter distrusted DHCP messages
  • Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
  • IP Source Guard prevents IP spoofing attacks
  • IP address access management to prevent unauthorized intruder
  Management
  • Switch Management Interfaces
- Console/Telnet Command Line Interface - Web switch management - SNMP v1 and v2c switch management - SSH/SSL and SNMP v3 secure access
  • Four RMON groups (history, statistics, alarms, and events)
  • IPv6 IP address/NTP/DNS management
  • Built-in Trivial File Transfer Protocol (TFTP) client
  • BOOTP and DHCP for IP address assignment
  • Firmware upload/download via HTTP/TFTP
  • DHCP Relay
  • DHCP Option 82
  • User Privilege levels control
  • Network Time Protocol (NTP)
  • Link Layer Discovery Protocol (LLDP)
  • SFP-DDM (Digital Diagnostic Monitor)
  • Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
  • Reset button for system reboot or reset to factory default
  • PLANET Smart Discovery Utility for deployment management
   Environmentally Hardened Design PLANET Industrial 8-Port Gigabit 802.3at PoE Switch, IGS-10020HPT, is equipped with rugged IP30 metal case for stable operation in heavy Industrial demanding environments. With IP30 industrial case protection, the IGS-10020HPT provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curbside traffic control cabinets. Being able to operate under wide temperature range from -40 to 75 degrees C, the IGS-10020HPT can be placed in almost any difficult environment. The IGS-10020HPT also allows either DIN rail or wall mounting for efficient use of cabinet space.    Redundant Ring, Fast Recovery for Surveillance System The IGS-10020HPT supports redundant ring technology and features strong rapid self-recovery capability to prevent interruptions and external intrusions. It incorporates advanced Redundant Ringtechnology, Spanning Tree Protocol (802.1w RSTP), and redundant power supply system into customer’s industrial automation network to enhance system reliability and uptime in harsh factory environments. The IGS-10020HPT also protects customer’s industrial network connectivity with switching recovery capability that is used for implementing fault tolerant ring and mesh network architectures. If the Industrial network was interrupted accidentally, the fault recovery times could be less than 50ms to quickly bring the network back to normal operation.    High Power PoE for Security and Public Service Applications To fulfill the demand of High Power PoE for network applications with Gigabit speed transmission under wide temperature, the IGS-10020HPT provides 8 10/100/1000Mbps ports featuring both IEEE 802.3af and High Power IEEE 802.3at Power over Ethernet (PoE) that combines up to 270-watt power output and data per port over one Cat.5E / 6 Ethernet cable. With a total 270-watt PoE budget on the whole system, the IGS-10020HPT is designed specifically to satisfy the growing demand of higher power consuming network PDs (powered devices) such as PTZ (Pan, Tilt & Zoom) / Speed Dome network cameras, multi-channel (802.11a / b / g / n) wireless LAN access points and other PoE network devices by providing PoE power double that the current conventional 802.3af PoE.    Intelligent Alive Check for Powered Device The IGS-10020HPT PoE Switch can be configured to monitor connected PD’s status in real-time via ping action. Once the PD stops working and responding, the IGS-10020HPT will recycle the PoE port power and bring the PD back to work. It also greatly enhances the reliability owing that the PoE port will reset the PD power, thus reducing administrator’s management burden.    PoE Schedule for Energy Saving Under the trend of energy saving worldwide and contributing to environmental protection on the Earth, the IGS-10020HPT can effectively control the power supply besides its capability of giving high watts power. The built-in “PoE schedule” function helps you to enable or disable PoE power feeding for each PoE port during specified time intervals and it is a powerful function to help SMB or enterprise save power and money.    Digital Input and Digital Output for External Alarm The IGS-10020HPT supports Digital Input and Digital Output on its front panel. This external alarm enables users to use Digital Input to detect and log external device status (such as door intrusion detector ), and send event alarm to the administrators. The Digital Output could be used to alarm the administrators if the IGS-10020HPT port shows link down, link up or power failure.    Layer 3 IPv4 and IPv6 Software VLAN Routing for Secure and Flexible Management To help customers stay on top of their businesses, the IGS-10020 series not only provides ultra high transmission performance and excellent Layer 2 technologies, but also IPv4/IPv6 software VLAN routing feature which allows to crossover different VLANs and different IP addresses for the purpose of having a highly secured, flexible management and simpler networking application.   Robust Layer 2 Features The IGS-10020HPT can be programmed for advanced switch management functions such as dynamic port link aggregation, Q-in-Q VLAN, private VLAN, Rapid Spanning Tree Protocol, Layer 2 to Layer 4 QoS, bandwidth control and IGMP snooping. The IGS-10020HPT provides 802.1Q tagged VLAN, and the VLAN groups allowed will be maximally up to 255. Via aggregation of supporting ports, the IGS-10020HPT allows the operation of a high-speed trunk combining multiple ports. It enables a maximum up to 5 trunk groups with 8 ports per trunking, and supports fail-over as well.   Efficient Management For efficient management, the IGS-10020HPT Managed Ethernet Switch is equipped with console, Web and SNMP management interfaces. With the built-in Web-based management interface, the IGS-10020HPT offers an easy-to-use, platform-independent management and configuration facility. For text-based management, the IGS-10020HPT can be accessed via Telnet and the console port. Moreover, it also offers secure remote management via any standard-based management software by supporting SNMPv3 connection which encrypts the packet content at each session.   Powerful Security The IGS-10020HPT offers comprehensive Layer 2 to Layer 4 Access Control List (ACL) for enforcing security to the edge. It can be used to restrict network access by denying packets based on source and destination IP address, TCP/UDP ports or defined typical network applications. Its protection mechanism also comprises 802.1x Port-nased and MAC-based user and device authentication. With the private VLAN function, communication between edge ports can be prevented to ensure user privacy. The network administrators can now construct highly secured corporate networks with considerably less time and effort than before.   Flexibility and Extension Solution The two mini-GBIC slots built in the IGS-10020HPT support dual speed, 100BASE-FX and 1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can flexibly choose the suitable SFP transceiver according to not only the transmission distance but also the transmission speed required. The distance can be extended from 550 meters (multi-mode fiber) up to 10/50/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.   Perfect Integration Solution for Outdoor IP PoE Camera and NVR System The IGS-10020HPT provides 8 10/100/1000Mbps 802.3at PoE ports and can offer sufficient PoE power for 8 PoE IP cameras at the same time. In addition, with the 2 100/1000BASE-X SFP interfaces, the IGS-10020HPT can connect to core fiber switch and send video stream to NVR and monitoring center. Through the high performance switch architecture, the IGS-10020HPT facilitates the recorded video files from the 8 PoE IP cameras to be saved in the NVR systems. Furthermore, the NVR systems can be controlled and monitored both in the local LAN and the remote site via Internet. The IGS-10020HPT undoubtedly brings an ideal secure surveillance system at a lower total cost.
Verfügbarkeit:
nicht lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - IGS-10020MT
IP30 Industrial 8Port +2Port Gbit SFP managed Switch
Preis auf Anfrage
• 8-Port 10/100/1000Base-T RJ-45 copper • 2 100/1000Base-X mini-GBIC/SFP slots, SFP type auto detection   Industrial Case / Installation • IP30 aluminum case protection • DIN-rail and wall mount design • Redundant Power Design  - 12 to 48V DC, redundant power with polarity reverse protect function  - AC 24V power adapter acceptable • Supports EFT protection 6000 VDC for power line • Supports 6000 VDC Ethernet ESD protection • -40 to 75 degrees C operating temperature   Layer 2 Features • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth • Storm Control support  - Multicast / Unknown-Unicast • Supports VLAN  - IEEE 802.1Q Tagged VLAN  - Up to 255 VLANs groups, out of 4095 VLAN IDs  - Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)  - Private VLAN Edge (PVE)  - Protocol-based VLAN  - MAC-based VLAN  - Voice VLAN • Supports Spanning Tree Protocol  - STP, IEEE 802.1D Spanning Tree Protocol  - RSTP, IEEE 802.1w Rapid Spanning Tree Protocol  - MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN  - BPDU Guard • Supports Link Aggregation  - 802.3ad Link Aggregation Control Protocol (LACP)  - Cisco ether-channel (Static Trunk)  - Maximum 5 trunk groups, up to 10 ports per trunk group  - Up to 20Gbps bandwidth (duplex mode) • Provides Port Mirror (many-to-1) • Port Mirroring of the incoming or outgoing traffic on a particular port • Supports E.R.P.S. (Ethernet Ring Protection Switching)   Quality of Service • Ingress Shaper and Egress Rate Limit per port bandwidth control • 8 priority queues on all switch ports • Traffic classification  - IEEE 802.1p CoS  - IP TOS / DSCP / IP Precedence  - IP TCP/UDP port number  - Typical network application • Strict priority and Weighted Round Robin (WRR) CoS policies • Supports QoS and In/Out bandwidth control on each port • Traffic-policing policies on the switch port • DSCP remarking   Multicast • Supports IGMP Snooping v1, v2 and v3 • Supports MLD Snooping v1 and v2 • Querier mode support • IGMP Snooping port filtering • MLD Snooping port filtering • MVR (Multicast VLAN Registration)   Security • IEEE 802.1x Port-based / MAC-based network access authentication • Built-in RADIUS client to co-operate with the RADIUS servers • TACACS+ login users access authentication • RADIUS / TACACS+ users access authentication • IP-based Access Control List (ACL) • MAC-based Access Control List • Source MAC / IP address binding • DHCP Snooping to filter untrusted DHCP messages • Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding • IP Source Guard prevents IP spoofing attacks • Auto DoS rule to defend DoS attack • IP address access management to prevent unauthorized intruder   Management • Switch Management Interfaces  -Web switch management  -Remote Telnet management  -SNMP v1, v2c, and v3 switch management  -SSH / SSL secure access • Four RMON groups (history, statistics, alarms, and events) • IPv6 IP Address / NTP / DNS management • Built-in Trivial File Transfer Protocol (TFTP) client • BOOTP and DHCP for IP address assignment • Firmware upload/download via HTTP / TFTP • DHCP Relay • DHCP Option 82 • User Privilege levels control • NTP (Network Time Protocol) • System Log • Link Layer Discovery Protocol (LLDP) Protocol • Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues • Reset button for system reboot or reset to factory default • PLANET Smart Discovery Utility for deploy management   PLANET IGS-10020MT is an Industrial 10-Port Full Gigabit Managed Ethernet Switch specially designed to build a full Gigabit backbone to transmit reliable but high speed data in heavy industrial demanding environments and forward data to remote network through fiber optic. It provides 8-port 10/100/1000Base-T copper and 2 extra 100/1000Base-X SFP fiber optic interfaces delivered in an IP30 rugged strong caiise with redundant power system. Besides support for 20Gbps switch fabric to handle extremely large amounts of video, voice and important data in a secure topology, the IGS-10020MT provides user-friendly but advanced IPv6 / IPv4 management interfaces and abundant L2 / L4 switching functions. It is the best investment for industrial business expanding or upgrading its network infrastructure    IPv6 / IPv4 Full-functioned Secure Switch for Building Automation Networking The IGS-10020MT is the ideal solution to fulfilling the demand of IPv6 management Gigabit Ethernet Switch, especially in the Industrial hardened environment. It supports both IPv4 and IPv6 management functions and can work with original network structure. It provides advanced Layer 2 to Layer 4 data switching and redundancy, Quality of Service traffic control, network access control and authentication, and Secure Management features to protect customer’s industrial and building automation network connectivity with reliable switching recovery capability that is suitable for implementing fault tolerant and mesh network architectures.    Redundant Ring, Fast Recovery for Surveillance System The IGS-10020MT supports redundant ring technology and features strong rapid self-recovery capability to prevent interruptions and external intrusions. It incorporates advanced ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) technology, Spanning Tree Protocol (802.1s MSTP), and redundant power input system into customer’s industrial automation network to enhance system reliability and uptime in harsh factory environments. In certain simple Ring network, the recovery time of data link can be as fast as 20 ms.    Environmentally Hardened Design With IP30 aluminum industrial case protection, the IGS-10020MT provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. It also possesses an integrated power supply source with wide range of voltages (12 to 48V DC or 24V AC) for worldwide high availability applications requiring dual or backup power inputs. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-10020MT can be placed in almost any difficult environment.    Flexible and Extendable Solution The 2 mini-GBIC slots built in the IGS-10020MT support dual-speed, 100Base-FX and 1000Base-SX/LX SFP (Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can flexibly choose the suitable SFP transceiver according to the transmission distance or the transmission speed required to extend the network efficiently. The IGS-10020MT supports SFP-DDM(Digital Diagnostic Monitor) function that can easily monitor real-time parameters of the SFP for network administrator, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.
Verfügbarkeit:
lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - IGS-1020TF
IP30 Industrial 8-Port 10/100/1000T + 2-Port 100/1000X SFP
Preis auf Anfrage
  • 8-port 10/100/1000BASE-T RJ45 with auto MDI/MDI-X function
  • 2 SFP slots, supporting 1000BASE-X and 100BASE-FX transceiver type auto-detection
  • unmanaged
    Industrial Case and Installation
  • IP30 metal case protection
  • DIN rail and wall mount design
  • Redundant Power Design
- 12 to 48V DC, redundant power with polarity reverse protect function - AC 24V power adapter acceptable
  • Supports 6000V DC Ethernet ESD protection
  • -40 to 75 degrees C operating temperature
  • Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az)
  Industrial-grade, Reliable and Flexible Network Deployment PLANET IGS-1020TF is an industrial 10-port full Gigabit Ethernet Switch providing non-blocking wire-speed performance and great flexibility for Gigabit Ethernet deployment and extension in harsh environment. It provides 8-port 10/100/1000BASE-T RJ45 copper and 2 extra 100/1000BASE-X SFP fiber optic interfaces delivered in an IP30 rugged strong case with redundant power system. The IGS-1020TF is well suited for applications in deploying surveillance system, secure control and wireless service in climatically demanding environments with wide temperature range from -40 to 75 degrees C.   Fiber-Optic Link Capability Enables Extension of Network Deployment The two mini-GBIC slots built in the IGS-1020TF support SFP auto-detection and dual speed as it features 100BASE-FX and 1000BASE-SX/LX SFP (Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can flexibly choose the suitable SFP transceiver according to the transmission distance or the transmission speed required to extend the network efficiently. The distance can be extended from 550 meters to 2 kilometers (multi-mode fiber) and 10/20/30/40/50/60/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications to uplink to backbone switch and monitoring center in long distance.   Environmentally Hardened Design With IP30 rugged metal case protection, the IGS-1020TF provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curbside traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-1020TF can be placed in almost any difficult environment. The IGS-1020TF also allows either DIN rail or wall mounting for efficient use of cabinet space.   Dual Power Input for High Availability Network System The IGS-1020TF features a strong dual power input system with wide-ranging voltages (12V~48V DC or 24V AC) incorporated into customer’s automation network to enhance system reliability and uptime. In the example below, when power supply 1 fails to work, the hardware failover function will be activated automatically to keep powering the IGS-1020TF via power supply 2 alternatively without any loss of operation.    Energy Saving The IGS-1020TF, incorporating advanced green networking technologies and and IEEE 802.3az protocol based power saving, is able to provide power saving up to 50% less energy but maintains high performance efficiently. ■ Link Down power saving The Link Down power saving goes beyond IEEE specifications to automatically lower power consumption for a given port when it is not linked. With the Link Down power saving technology, the IGS-1020TF will automatically adjust power usage of the ports that are shut down or not connected to network device.   ■ Intelligent power scale based on cable length Intelligent power scale is an intelligent algorithm that actively determines the appropriate power level based on cable length. When the IGS-1020TF is connected with Ethernet cable shorter than 20m, a device can obtain maximum power saving because the IGS-1020TF would automatically detect the Ethernet cable length and diminish power usage. The connected device can substantially reduce the overall power consumption, which makes a significant contribution to energy saving   Robust Protection The IGS-1020TF provides contact discharge of ±6KV DC and air discharge of ±8KV DC for Ethernet ESD protection. It also supports ±4KV surge immunity to improve product stability and protects users’ networks from devastating ESD attacks, making sure the flow of operation does not fluctuate.   Plug and Power Network Deployment All of the RJ45 copper interfaces in the IGS-1020TF support 10/100/1000Mbps auto negotiation for optimal speed detection through RJ45 Category 6, 5 or 5e cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight-through or crossover cables.  
Verfügbarkeit:
nicht lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - IGS-801T
IP30 Slim type 8-Port unmanaged Industrial Gigabit Ethernet
Preis auf Anfrage
  • 8-port 10/100/1000BASE-T RJ45 with auto MDI/MDI-X function
  Layer 2 Features
  • Complies with IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T Ethernet standard
  • Supports auto-negotiation and 10/100Mbps half/full duplex and 1000Mbps full duplex mode
  • High-performance Store and Forward architecture, broadcast storm control and runt/CRC filtering eliminate erroneous packets to optimize the network bandwidth
  • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
  • 4K absolute MAC address and 16Gbps switching fabric support
  • 1.5Mbits SRAM packet buffer
  • 9K jumbo packet size support
  • IEEE 802.1p CoS support
  • Automatic address learning and address aging
  • CSMA/CD Protocol
  Industrial Case and Installation
  • IP30 metal case
  • DIN rail and wall-mount design
  • 12 to 48V DC, redundant power with polarity reverse protect function and connective, removable terminal block for master and  
   slave power; 24V AC power support
  • -40 to 75 degrees C operating temperature
    New slim type with more practicability and convenience After entering the Industrial Ethernet market with popular ISW/IFT Fast Ethernet Switch/Converter series, PLANET has released the advanced industrial hardened Gigabit Ethernet Switch series with new slim type, IP-30 metal case. The compact, IP-30 standard metal case allows either DIN rail or wall mounting for efficient use of cabinet space. The IGS-801T, one of the new models, is equipped with 8 10/100/1000Mbps auto negotiation ports and operates reliably in heavy industrial demanding environments.   Stable performance under difficult environments The IGS-801T provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Being able to operate under the temperature range from -40 to 75 degrees C, the IGS-801T can be placed in almost any difficult environment. The IGS-801T also possesses an integrated power supply source with wide range of voltages (12 to 48V DC) for worldwide high availability applications requiring dual or backup power inputs.   Robust Switch performance The IGS-801T offers high performance switch architecture. With the 8 10/100/1000Mbps Gigabit Ethernet ports providing non-blocking switch fabric and wire-speed throughput as high as 16Gbps and the 8K MAC Address table, the IGS-801T can perform wire-speed packets transfer without risk of packet loss.   The flow control function enables the IGS-801T to provide fast and reliable data transfer. The Gigabit port with 9K Jumbo frame supported can handle extremely large amounts of data transmission in industrial topology that forward data to central control room.   All of the RJ-45 copper interfaces in the IGS-801T support 10/100/1000Mbps auto negotiation for optimal speed detection through RJ-45 Category 6, 5 or 5e cables. The standard auto-MDI/MDI-X support can detect the type of connection to any Ethernet device without requiring special straight or crossover cables.
Verfügbarkeit:
nicht lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Hersteller, PLANET - VCG-1500WG-LTE-EU
Vehicle 4G LTE Cellular Wireless Gateway w/ 5-Port 10/100TX, SIM, GPS, 802.11n
Preis auf Anfrage
  • 4x 10/100BASE-TX RJ45 LAN ports, auto-negotiation, auto MDI/MDI-X
  • 1x 10/100BASE-TX RJ45 WAN port, auto-negotiation, auto MDI/MDI-X
  • 1x 4G LTE 2.3 dBi antenna
  • 2x 2.4G WiFi 2dBi antennas
  • 1x GPS antenna
  • 1x SIM card slot
  • 1x console port
  • 2x TF card slots  to save files for Wi-Fi advertising
Cellular Interface:
  • Supports multi-band connectivity with FDD LTE/ TDD LTE/ WCDMA/ GSM/ LTE Cat4
  • Built-in SIM and broadband backup for network redundancy
  • One detachable antenna for 4G LTE connection
  • LED indicators for connection status (3G/4G)
Wi-Fi Interfaces:
  • Complies with IEEE 802.11b/g/n 2.4GHz
  • Two detachable antennas for wireless connection
  • 64-/128-bit WEP, WPA/WPA2 and WPA-PSK/WPA2-PSK (TKIP/AES encryption),
  • LED indicators for status 
Case and Installation:
  • IP30 metal case
  • Mounting brackets for vehicles
  • Power requirement: 6~32V DC
  • Supports 15KV DC Ethernet ESD protection
  • -25 to 65 degrees C operating temperature 
Advanced Features:
  • Supports demilitarized zone (DMZ).
  • Supports VPN client, including GRE, PPTP, IPSec, L2TP 
  • Supports NAT port mapping function, such as SNAT, DNAT
  • Supports Static Routing to display current routing information of the gateway
  • Supports QoS for bandwidth management
  • Supports Dynamic DNS and PLANET DDNS
  • Supports WAN connection types: DHCP client, static IP and PPPoE client
  • Secures network connection
    • IP filter
    • URL filter
    • MAC filter 
Management:
  • Gateway management interfaces
    • Console/Telnet Command Line interface 
    • Web  management
  • Gateway Maintenance
    • Firmware upload via HTTP, TFTP
    • Restore or Reset button for reset to factory default
    • Dual images
  • SNTP (Simple Network Time Protocol)
    System log
  • System tool, such as ping and trace 
  • Configuration backup and restore
  • Supports CMS (Central Management System) and Wifidog for remote management and  Wi-Fi advertising

Internet of Vehicles via 4G LTE Cellular Gateway:
PLANET VCG-1500WG-LTE is a reliable, secure and high-bandwidth communications vehicle cellular gateway for demanding mobile applications and IoV (Internet of Vehicles) deployments. It features 4G LTE (Long Term Evolution), wireless AP, five Ethernet ports (4 LAN and 1 WAN), GPS,  VPN technology and bandwidth management bundled in a mountable metal case to establish a public network connection and allows passengers to access Internet. High-performance 4G LTE :
The VCG-1500WG-LTE is able to reach a download (DL) speed of up to 100Mbps and an upload (UL) speed of 50Mbps. The Cellular Gateway also supports multi-band connectivity including LTE FDD, TDD, HSDPA, WCDMA and GSM for a wide range of applications.  Wireless Access Point:
With an integrated 802.11n Wireless Access Point, the gateway supports data rate up to 300Mbps and is also compatible with 2.4GHz 802.11b/g/n equipment. The Wireless Protected Access (WPA-PSK/WPA2-PSK) and Wireless Encryption Protocol (WEP) features enhance the level of transmission security and access control over Wireless LAN.  GPS Included:
The VCG-1500WG-LTE is equipped with one convenient feature and that is GPS (global positioning system). It is a positioning system based on a network of satellites that continuously transmit necessary data. More signals transmitted from more satellites can triangulate its location on the ground, meaning any location can be easily tracked anytime.  Cost-effective VPN Solution:
The VCG-1500WG-LTE provides a complete data security and privacy feature for access and exchange of sensitive data. The full VPN capability of the VCG-1500WG-LTE including built-in PPTP, LT2P, and IPSec VPN client functions with DES/3DES/AES encryption and MD5/SHA-1 authentication makes the shared connection more secure and flexible. The IPSec VPN also makes the private tunnel over Internet more secure for enterprises doing business transactions. Dual TF Cards for Wi-Fi Advertising Contents:
The VCG-1500WG-LTE provides dual TF cards and the capacity of each card is up to 128GB. The TF cards can store thousands of advertising data and movie files. The administrator is able to upload these files to TF cards via FTP locally. Besides, through CMS (Central Management System), administrator is able to upload and maintain these files remotely. The device will display advertising contents when users access to the Wi-Fi after authentication.  Superior Management Functions:
For networking management features, the VCG-1500WG-LTE provides such functions as  DMZ, QoS and Wifidog, as well as full secure functions including Network Address Translation (NAT), IP/URL/MAC filtering. The VCG-1500WG-LTE has 4G and WAN connection failover characteristics, which can automatically switch over to the redundant, stable WAN connection to keep users always online without missing any fascinating moments. User-friendly and Secure Management:
For efficient management, the VCG-1500WG-LTE is equipped with console, web and Wifidog management interfaces. With the built-in web-based management interface, the VCG-1500WG-LTE offers an easy-to-use, platform independent management and configuration facility. The VCG-1500WG-LTE supports Wifidog and it can be managed via CMS (Central Management System) for remote management and Wi-Fi advertising. 
Verfügbarkeit:
nicht lagernd
Login für mehr Info
mehr Informationen
zu Favoriten
Seite /