• Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u, 100BASE-TX and 100BASE-FX Ethernet standards
• One 10/100BASE-TX port with RJ45 connector
• One 100BASE-FX port with ST/SC/WDM connector supporting multi-mode or single-mode fiber optic cable
• Auto-negotiation and auto-MDI / MDI-X for 10/100BASE-TX port
• Back-pressure and IEEE 802.3x compliant flow control and full wire-speed forwarding rate
• Link Loss Return (LLR) switch on each fiber optic is to aid in troubleshooting remote network connections
• Link Loss Carry Forward (LLCF) works with LLR in diagnosing network connections

  Distance Extended with Fiber Optic Cable PLANET FST-80x Smart Media Converter series provides media conversion between 10/100BASE-TX and 100BASE-FX interfaces, such as multi-mode ST/SC connectors (2km), single-mode SC connector (15/35/50km) and single fiber connector using the wavelength-division multiplexing (WDM) technology (20/60km) to enable to extend links over long distances using fiber optic cable.    Enhanced Smart Management Features The FST-80x series provides auto MDI/MDI-X on their TP port and store-and-forward mechanism to eliminate faulty packets. Use the DIP switch from the FST-80x to configure the available smart functions, such as the half/full duplex, auto-negotiation / force and 10/100Mbps options for TP and fiber interfaces. Besides, the Link Loss Return (LLR) and Link Loss Carry Forward (LLCF) functions can immediately alarm network administrator once there is a media link issue, thus helping to monitor the status of the entire network.    Easy Installation The FST-80x series can be connected easily and cost-effectively as these smart media converters can be used as a standalone unit when powered on by its DC adapter, or used as a slide-in module connected to PLANET 19-inch, 16-slot web smart/managed media converter chassis (MC-1600MR/MC-1600MR48 and MC-1610MR/MC-1610MR48). When working with the web smart/managed media converter chassis, the status of the FST-80x can be monitored via the local RS-232 console and remote web interface.

• Complies with IEEE 802.3, IEEE 802.3u 10 / 100Base-TX and 100Base-FX
• IEEE 802.3x full-duplex flow-control, back-pressure in Half-duplex eliminate packet loss
• TS-1000 / OAM function built-in, the device can be remotely monitored with port link status
• Dual 100Base-FX SFP fiber optic
• One 10 / 100Base-TX copper
• Auto-negotiation for 100Base-TX half-duplex or 100Base-T full-duplex
• Supports auto MDI / MDI-X function
• Supports maximum frame size up to 2046Kbytes
• Link status auto-detect and redundant on dual ports with the same connector type
• Only primary port is active at a time, the backup port is blocked
• While primary port link fail occurrences, the traffic will swap to backup port automatically
• Once the primary port status is back to linkup, the traffic will swap from backup port to primary port
• Hardware redundant swaps less than 10 ms

  PLANET FT-1205A is a 3-port Redundant Media Converter which supports conversion between 10 / 100Base-TX and 100Base-FX network. The difference with the other one-port channel media converter is the Redundant Media Converter. It is designed for critical networks that require fibers or copper links to automatically recover less than 10ms, such as ISPs, telecoms, hospitals, banks and enterprises.   Via the built-in DIP switches, the converter can be configured as 3-port Ethernet switch or 2-port redundant media converter. With the 3-port switch mode, it can operate Store-and-Forward mechanism with high performance, and it can also prevent packet loss via IEEE 802.3x flow control (full-duplex) and back pressure (half-duplex).   With the 2-port redundant mode, it provides less than 10ms redundancy of link for highly critical Ethernet applications. The redundant mode supports auto-recover function. If the destination port of a packet is link-down, it forwards the packet to the other port of the backup pair.   The SFP slot supports single-mode, multi-mode and WDM small-form factory type transceiver modules for various applications. The FT-1205A is with high reliability and flexibility to extend the distance up to 2km, 20km or longer. It depends on the 100Base-FX SFP transceiver modules. The Ethernet signal that allows two types of segments to connect easily, efficiently and inexpensively.   The converters can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter Chassis, MC-700, MC-1500, MC-1500R and MC-1500R48. As to the other PLANET media converters (FT series), they're hot swappable in MC chassis.

• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard • Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568 • One fiber-optic, 1310nm wavelength, connector type and distance vary with model    - FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm    - FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm • Data Transfer Rate:   - TP: 10/100Mbps     - FX: 100Mbps • Duplex mode support:  - Full or half-duplex mode by auto-negotiation (TP)   - Full or half-duplex mode by DIP switch (FX) • LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL • DIP switch: 2 DIP switches   - Rear DIP switch: FX duplex mode selection   - Side DIP switch: LFP (Link Fault Pass-through) mode selection • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets     PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• Complies with IEEE 802.3, IEEE 802.3u 10/100BASE-TX, 100BASE-FX standard • Connectors: One RJ45 (auto-MDI/MDI-X) twisted pair, EIA568 • One fiber-optic, 1310nm wavelength, connector type and distance vary with model    - FT-806A20 / FT-806A60: Tx-1310nm, Rx-1550nm    - FT-806B20 / FT-806B60: Tx-1550nm, Rx-1310nm • Data Transfer Rate:   - TP: 10/100Mbps     - FX: 100Mbps • Duplex mode support:  - Full or half-duplex mode by auto-negotiation (TP)   - Full or half-duplex mode by DIP switch (FX) • LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL • DIP switch: 2 DIP switches   - Rear DIP switch: FX duplex mode selection   - Side DIP switch: LFP (Link Fault Pass-through) mode selection • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the loss of packets     PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.    The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function    LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.  

• Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX, IEEE 802.3afPower over Ethernet standards
• Auto negotiation for 10/100Base-TX half duplex mode or full duplex mode, auto-MDI / MDI-X function on copper port
• IEEE 802.3x full duplex flow control and back pressure in half duplex eliminate packets loss
• Provides DC 48V power over RJ-45 Ethernet cable to devices with Ethernet port
• Auto-detect PoE IEEE 802.3af equipment; protects devices from being damaged by incorrect installation
• 100Base-FX interface for up to 2km (multi-mode fiber 50µm/125µm, 62.5µm/125µm) on FTP-802
• 100Base-FX interface for up to 15km (single-mode fiber 9µm/125µm) on FTP-802S15
• DIP-switch: LFP (Link Fault Pass-through) mode selection
• Compact in size, easy to install
• LED indicators for easy network diagnostics 

  More than a Fiber Media Converter -- a Power over Ethernet Injector as well The best data link and power sourcing solution for long reach network equipment   PLANET FTP-80x series is ideal for remote network equipment deployments, using two networking technologies:

• Media Conversion : 100Base-FX to 10/100Base-TX
• Power over Ethernet : Power Sourcing Equipment (PSE), PoE Injector

Providing both PoE and fiber-optic interfaces, the FTP-80x is ideal for service providers, campuses and public areas requiring to deploy the PoE for wireless access points, IP-based surveillance cameras or IP phones in any places easily, efficiently and cost effectively.   PoE Optimizes the Installation and Power Management of Network Devices The IEEE 802.3af capabilities of the FTP-80x reduce installation costs for many new network productivity devices. As an IEEE 802.3af Power over Ethernet Injector, the FTP-80x provides DC 48V voltage over Ethernet cables. It allows the twisted pair cable between the FTP-80x and IEEE 802.3af compliant PD (Powered Device) or PoE Splitter (such as POE-151S-5V / 12V) to transfer data and power simultaneously.   Fiber-optic Link Capability Extends the Range of Network Deployments The maximum distance from the PoE PSE and PD is 100 meters. To extend the deployment range of network device, the FTP-80x is integrated with fiber interface. The FTP-80x PoE Media Converters are used to convert optical Ethernet signal to electrical Ethernet signal that allows two type of segments to connect easily, efficiently and inexpensively. It can convert 10/100Base-TX signal to 100Base-FX signal and provides the diverse fiber connecting types of options to meet different network applications. By selecting models, the maximum networking distance can extend to as long as 15 kilometers and still sustain the transmission performance as high as 100Mbps. It works in high performance of Store and Forward mechanism and if also can prevent packet loss with IEEE 802.3x flow control (full-duplex). With the LFP (Link Fault Pass-through function),(LLCF / LLR) and the DIP switch design, it can immediately alarm administrators problems of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function.   Advantage of Combined PoE and Media Conversion With the data, long reach fiber capability and PoE from one unit, the FTP-80x will reduce cables and eliminate the need for dedicated electrical outlets on the wall, ceiling or any unreachable place. It frees the security IP camera and wireless AP deployment from restrictions due to power outlet locations. Power and data switching are integrated into one unit and delivered over a single cable, eliminating costs for additional AC wiring and reducing installation time.