• 48x 10/100/1000BASE-T RJ45 copper ports
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 to DB9 console interface for switch basic management and setup
• One 10/100BASE-TX Management port 

Stacking Features:

• IP Stacking
  
  • Connects with stack member via Gigabit TP, SFP and 10G SFP+ interfaces
  • Single IP address management, supporting up to 16 IP units stacked together
• Hardware Stacking
  
  • Virtualized multiple SGS-5240 switch series stacked into one logical device
  • Connects with stack member via assigned 10G SFP+ interfaces
  • Single IP address stack management, supporting up to 6 hardware units stacked together
  • Stacking architecture supports redundant ring mode

IP Routing Features:

• IPv4/IPv6 hardware static routing
• Routing interface provides per VLAN routing mode 

Layer 2 Features:

• Supports VLAN
  
  • IEEE 802.1Q tag-based VLAN
  • Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported
  • GVRP for dynamic VLAN management
  • Protocol-based VLAN
  • MAC-based VLAN
  • IP subnet-based VLAN
  • Voice VLAN
• Supports Link Aggregation
  
  • 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
• Supports Spanning Tree Protocol
  
  • STP, IEEE 802.1D (Classic Spanning Tree Protocol)
  • RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
  • MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
  • Supports BPDU & root guard
• Port mirroring to monitor the incoming or outgoing traffic on a particular port (many to one)
• Supports G.8032 ERPS (Ethernet Ring Protection Switching)
• Loop protection to avoid broadcast loops
• Link Layer Discovery Protocol (LLDP)
• Compatible with Cisco uni-directional link detection (UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices 

Quality of Service:

• Input and output rate limit per port bandwidth control
• 8 priority queues on all switch ports
  
  • IEEE 802.1p CoS/DSCP/IP Precedence
  • VLAN ID
  • ACL
  • Policy-based ingress and egress QoS 

Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD snooping v1 and v2
• Querier mode support
• IPv4 IGMP snooping port filtering
• IPv6 MLD snooping port filtering
• MVR (Multicast VLAN Registration) 

Security:

• Authentication
  
  • IEEE 802.1x port-based/MAC-based network access authentication
  • IEEE 802.1x authentication with guest VLAN
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • RADIUS/TACACS+ users access authentication
  • Guest VLAN assigns clients to a restricted VLAN with limited services
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List (ACL)
  • Time-based ACL
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder 

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
  
  • Console and Telnet Command Line Interface 
  • HTTP web switch management
  • SNMP v1 and v2c switch management
  • SSHv2, SSLv3 and SNMP v3 secure access
• SNMP Management
  
  • Four RMON groups (history, statistics, alarms, and events) 
  • SNMP trap for interface Link Up and Link Down notification
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• • Firmware upload/download via HTTP
  • Reset button for system reboot or reset to factory default
  • Dual images
• DHCP Functions:
  
  • DHCP Relay
  • DHCP Option 82
  • DHCP Server
• User Privilege levels control
• Network Time Protocol (NTP) and SNTP
• Network Diagnostic
  
  • SFP-DDM (Digital Diagnostic Monitor)
  • Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
  • ICMPv6/ICMPv4 remote ping
• Syslog remote alarm
• System Log 

• 24-port 10/100/1000BASE-T Gigabit Ethernet RJ45 with 24-port IEEE 802.3at PoE+ injector
• 4 10GBASE-SR/LR SFP+ slots, backward compatible with 1000BASE-SX/LX/BX SFP
• RJ45 to DB9 console interface for switch basic management and setup 

Stacking Features:

• Hardware Stacking
  Virtualized multiple SGS-6310 series stacked into one logical facility
• Connects with stack members via assigned 10G SFP+ interfaces
• Single IP address stack management, supporting up to 8 hardware units stacked together
• Stacking architecture supports redundant Ring mode

IP Routing Features:

• IPv4 routing protocol supports RIPv1/v2 and OSPFv2
• IPv6 routing protocol supports RIPng and OSPFv3
• Routing interface provides per VLAN routing mode 
• VRRPv1/v3 protocol for redundant routing deployment 
• Supports route redistribution 
• Supports hardware-based wire-speed VLAN routing 

Multicast Routing Features:

• Supports IPv4 IGMP v1/v2/v3, IGMP Snooping.
• Supports IGMP Fast Leave, MVR, IGMP filter
• Supports IPv6 MLD V1, MLD snooping 

Layer 2 Features:

• 16K MAC address table, automatic source address learning and aging
• Supports VLAN
  
  • IEEE 802.1Q tag-based VLAN
  • Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported
  • GVRP protocol for dynamic VLAN management
  • Private VLAN Edge (PVE) supported
  • MAC-based VLAN
  • IP subnet-based VLAN
  • Voice VLAN
• Supports Link Aggregation
  
  • IEEE 802.3ad LACP (Link Aggregation Control Protocol)
  • Static mode and LACP mode
  • Maximum 64 trunk groups, up to 8 ports per trunk group
• Supports Spanning Tree Protocol
  
  • STP, IEEE 802.1D (Classic Spanning Tree Protocol)
  • RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
  • MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
  • Supports BPDU & root guard
• Port mirroring to monitor the incoming or outgoing traffic on a particular port (one-to-one and many-to-one)
• Provides port mirror (many-to-1)
• Supports G.8032 ERPS (Ethernet Ring Protection Switching)
• Loop protection to avoid broadcast loops
• Link Layer Discovery Protocol (LLDP)
• Compatible with Cisco UDLD (uni-directional link detection) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices 

Quality of Service:

• 8 priority queues on all switch ports
• Support for strict priority and WRR (Weighted Round Robin) CoS policies
• Traffic classification
  
  • IEEE 802.1p CoS/ToS
  • IPv4/IPv6 DSCP
  • Port-based WRR
• Strict priority and WRR CoS policies 

Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD v1 snooping
• Querier mode support
• Supports Multicast VLAN Register (MVR) 

Security:

• Authentication
  
  • IEEE 802.1x port-based network access authentication
  • MAC-based network access authentication 
  • Built-in RADIUS client to cooperate with the
  • RADIUS servers for IPv4 and IPv6
  • RADIUS/TACACS+ login users access authentication
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List
  • Time-based ACL
• DHCP snooping to filter distrusted DHCP messages
• IP Source Guard prevents IP spoofing attacks
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interface
  
  • Console and Telnet Command Line Interface 
  • HTTP Web switch management
  • SNMP v1 and v2c switch management
  • SSHv1/v2, TLSv1.2 and SNMPv3 secure access
• SNMP Management
  
  • Four RMON groups 1, 2, 3, 9 (history, statistics, alarms and events)
  • SNMP trap for interface Link Up and Link Down notification
• BOOTP and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via TFTP or HTTP Protocol for IPv4 and IPv6
• SNTP (Simple Network Time Protocol) for IPv4 and IPv6
• User privilege levels control
• Syslog server for IPv4 and IPv6
• Supports sFlow 
• DHCP Functions
  
  • DHCP Option82
  • DHCP server/relay/client
• Network Diagnostic
  
  • Supports ping, traceroute function for IPv4 and IPv6
  • Supports DDM (Digital Diagnostic Monitor)
• Supports ISSU (In-service Software Upgrade) to guarantee non-stop user data transmission when the system is upgraded.

• 24x 100/1000BASE-X mini-GBIC/SFP slots
• 8x 10/100/1000BASE-T RJ45 copper ports, shared with Port-1 to Port-8
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 to DB9 console interface for switch basic management and setup
• 1x USB2.0 interface for configuration and firmware storage

  IP Stacking:

• Connects with stack member via both Gigabit TP and SFP interfaces
• Single IP address management, supporting up to 24 units stacked together

  IP Routing Features:

• IP routing protocol supports RIPv1/v2, RIPng, OSPFv2/v3, BGP4/4+
• Routing interface provides per VLAN routing mode
• VRRPv1/v3 protocol for redundant routing deployment
• Supports route redistribution

  Multicast Routing Features:

• Supports PIM-DM (Protocol Independent Multicast – Dense Mode) and PIM-SM (Protocol Independent Multicast – Sparse Mode) and PIM-SSM (Protocol Independent Multicast – Source Specific Multicast)
• Supports DVMRP (Distance Vector Multicast Routing Protocol)
• Supports IGMP v1/v2/v3 and MLD v1/v2

  Layer 2 Features:

• Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit Ethernet standard
• Supports auto-negotiation and half-duplex/full-duplex modes for all 10BASE-T, 100BASE-TX and 1000BASE-T ports
• Auto-MDI/MDI-X detection on each RJ45 port
• Prevents packet loss flow control
• IEEE 802.3x pause frame flow control in full-duplex mode
• Back pressure flow control in half-duplex mode
• High performance Store-and-Forward architecture, broadcast storm control, port loopback detect
• 16K MAC address table, automatic source address learning and aging
• Supports VLAN
• IEEE 802.1Q tag-based VLAN
• GVRP for dynamic VLAN management
• Up to 256 VLANs groups, out of 4041 VLAN Ids
• Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported
• Private VLAN Edge (PVE) supported
• GVRP protocol for Management VLAN
• Protocol-based VLAN
• MAC-based VLAN
• IP subnet VLAN
• Supports Link Aggregation
• Maximum 128 trunk groups, up to 8 ports per trunk group
• IEEE 802.3ad LACP (Link Aggregation Control Protocol)
• Cisco ether-channel (static trunk)
• Supports Spanning Tree Protocol
• STP, IEEE 802.1D (Classic Spanning Tree Protocol)
• RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
• MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
• Supports BPDU & root guard
• Port mirroring to monitor the incoming or outgoing traffic on a particular port (many to many)
• Provides port mirror (many-to-1)

  Quality of Service:

• 8 priority queues on all switch ports
• Support for strict priority and WRR (Weighted Round Robin) CoS policies
• Traffic classification
• IEEE 802.1p CoS/ToS
• IPv4/IPv6 DSCP
• Port-based WRR
• Strict priority and WRR CoS policies

  Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3; IPv6 MLD v1 and v2 snooping
• Querier mode support
• Supports Multicast VLAN Register (MVR)

  Security:

• IEEE 802.1x port-based network access authentication
• MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers for IPv4 and IPv6
• TACACS+ login users access authentication
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Supports DHCP snooping
• Supports ARP inspection
• IP Source Guard prevents IP spoofing attacks
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding

  Management:

• Management IP for IPv4 and IPv6
• Switch Management Interface
• Console/Telnet Command Line Interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure access
• BOOTP and DHCP for IP address assignment
• Firmware upload/download via TFTP or HTTP Protocol for IPv4 and IPv6
• SNTP (Simple Network Time Protocol) for IPv4 and IPv6
• User privilege levels control
• Syslog server for IPv4 and IPv6
• Supports DDM
• Four RMON groups 1, 2, 3, 9 (history, statistics, alarms and events)
• Supports sFlow
• Supports ULDP
• Supports ULPP (Uplink Protection Protocol)
• Supports ULSM (Uplink State Monitor protocol)
• Supports LLDP/LLDP MED
• Supports DHCP Option82, Option37/38
• Supports ping, trace route function for IPv4 and IPv6

• 24-port 10/100/1000BASE-T Gigabit Ethernet RJ45 with 24-port IEEE 802.3at/af PoE injector
• 4 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• Up to 24 ports of IEEE 802.3af/802.3at devices powered
• RJ45 to DB9 console interface for switch basic management and setup

  Powerful Layer 3 Gigabit Routing and Power over Ethernet Solution PLANET SGS-6341-24P4X is a Layer 3 PoE Stackable Managed Gigabit Switch that provides high-density performance, Layer 3 static routing, RIP (Routing Information Protocol) and OSPF (Open Shortest Path First). With 128Gbps switching fabric, the SGS-6341-24P4X can handle extremely large amounts of data in a secure topology linking to an enterprise backbone or high capacity servers. The powerful WRR (Weighted Round Robin) and Network Security features make the SGS-6341-24P4X perform effective data traffic control for ISP and enterprise VoIP, video streaming, and multicast applications. The SGS-6341-24P4X has 24 IEEE 802.3at PoE+ ports and PoE budget up to 370 watts for catering to medium to large scale of VoIP or IP surveillance networks at a lower total cost.

• 24x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 to DB9 console interface for switch basic management and setup

  IP Stacking:

• Connects with stack member via both Gigabit TP and SFP interfaces
• Single IP address management, supporting up to 24 units stacked together

  IP Routing Features:

• IP routing protocol supports RIPv1/v2, RIPng, OSPFv2/v3, BGP4/4+
• Routing interface provides per VLAN routing mode
• VRRPv1/v3 protocol for redundant routing deployment
• Supports route redistribution

  Multicast Routing Features:

• Supports PIM-DM (Protocol Independent Multicast – Dense Mode) and PIM-SM (Protocol Independent Multicast – Sparse Mode) and PIM-SSM (Protocol Independent Multicast – Source Specific Multicast)
• Supports DVMRP (Distance Vector Multicast Routing Protocol)
• Supports IGMP v1/v2/v3 and MLD v1/v2

  Layer 2 Features:

• Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit Ethernet standard
• Supports auto-negotiation and half-duplex/full-duplex modes for all 10BASE-T, 100BASE-TX and 1000BASE-T ports
• Auto-MDI/MDI-X detection on each RJ45 port
• Prevents packet loss flow control
• IEEE 802.3x pause frame flow control in full-duplex mode
• Backpressure flow control in half-duplex mode
• High performance Store-and-Forward architecture, broadcast storm control, port loopback detect
• 16K MAC address table, automatic source address learning and aging
• Supports VLAN
• IEEE 802.1Q tag-based VLAN
• GVRP for dynamic VLAN management
• Up to 256 VLANs groups, out of 4041 VLAN Ids
• Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported
• Private VLAN Edge (PVE) supported
• GVRP protocol for Management VLAN
• Protocol-based VLAN
• MAC-based VLAN
• IP subnet VLAN
• Supports Link Aggregation
• Maximum 128 trunk groups, up to 8 ports per trunk group
•  IEEE 802.3ad LACP (Link Aggregation Control Protocol)
• Cisco ether-channel (static trunk)
• Supports Spanning Tree Protocol
• STP, IEEE 802.1D (Classic Spanning Tree Protocol)
• RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
• MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
• Supports BPDU & root guard
• Port mirroring to monitor the incoming or outgoing traffic on a particular port (many to many)
• Provides port mirror (many-to-1)

  Quality of Service:

• 8 priority queues on all switch ports
• Support for strict priority and WRR (Weighted Round Robin) CoS policies
• Traffic classification
• IEEE 802.1p CoS/ToS
• IPv4/IPv6 DSCP
• Port-based WRR
• Strict priority and WRR CoS policies

  Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3; IPv6 MLD v1 and v2 snooping
• Querier mode support
• Supports Multicast VLAN Register (MVR)

  Security:

• IEEE 802.1x port-based network access authentication
• MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers for IPv4 and IPv6
• TACACS+ login users access authentication
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Supports DHCP snooping
• Supports ARP inspection
• IP Source Guard prevents IP spoofing attacks
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding

  Management:

• Management IP for IPv4 and IPv6
• Switch Management Interface
• Console/Telnet Command Line Interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure access
• BOOTP and DHCP for IP address assignment
• Firmware upload/download via TFTP or HTTP Protocol for IPv4 and IPv6
• SNTP (Simple Network Time Protocol) for IPv4 and IPv6
• User privilege levels control
• Syslog server for IPv4 and IPv6
• Supports DDM
• Four RMON groups 1, 2, 3, 9 (history, statistics, alarms and events)
• Supports sFlow
• Supports ULDP
• Supports ULPP (Uplink Protection Protocol)
• Supports ULSM (Uplink State Monitor protocol)
• Supports LLDP/LLDP MED
• Supports DHCP Option82, Option37/38
• Supports ping, trace route function for IPv4 and IPv6

• 48x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 to DB9 console interface for switch basic management and setup

  IP Stacking:

• Connects with stack member via both Gigabit TP and SFP interfaces
• Single IP address management, supporting up to 24 units stacked together

  IP Routing Features:

• IP routing protocol supports RIPv1/v2, RIPng, OSPFv2/v3, BGP4/4+
• Routing interface provides per VLAN routing mode
• VRRPv1/v3 protocol for redundant routing deployment
• Supports route redistribution

  Multicast:

• Routing FeaturesSupports PIM-DM (Protocol Independent Multicast – Dense Mode) and PIM-SM (Protocol Independent Multicast – Sparse Mode) and PIM-SSM (Protocol Independent Multicast – Source Specific Multicast)
• Supports DVMRP (Distance Vector Multicast Routing Protocol)
• Supports IGMP v1/v2/v3 and MLD v1/v2

  Layer 2 Features:

• Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit Ethernet standard
• Supports auto-negotiation and half-duplex/full-duplex modes for all 10BASE-T, 100BASE-TX and 1000BASE-T ports
• Auto-MDI/MDI-X detection on each RJ45 port
• Prevents packet loss flow control
• IEEE 802.3x pause frame flow control in full-duplex mode
• Back-pressure flow control in half-duplex mode
• High performance Store-and-Forward architecture, broadcast storm control, port loopback detect
• 16K MAC address table, automatic source address learning and aging
• Supports VLAN
• IEEE 802.1Q tag-based VLAN- GVRP for dynamic VLAN management
• Up to 256 VLANs groups, out of 4041 VLAN Ids
• Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported
• Private VLAN Edge (PVE) supported
• GVRP protocol for Management VLAN- Protocol-based VLAN
• MAC-based VLAN
• IP subnet VLAN
• Supports Link Aggregation
• Maximum 12 trunk groups, up to 8 ports per trunk group
• IEEE 802.3ad LACP (Link Aggregation Control Protocol)
• Cisco ether-channel (static trunk)
• Supports Spanning Tree Protocol
• STP, IEEE 802.1D (Classic Spanning Tree Protocol)
• RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
• MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
• Supports BPDU & root guard
• Port mirroring to monitor the incoming or outgoing traffic on a particular port (many to many)
• Provides port mirror (many-to-1)

  Quality of Service:

• 8 priority queues on all switch ports
• Support for strict priority and WRR (Weighted Round Robin) CoS policies
• Traffic classification
• IEEE 802.1p CoS/ToS- IPv4/IPv6 DSCP- Port-based WRR
• Strict priority and WRR CoS policies

  Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3; IPv6 MLD v1 and v2 snooping
• Querier mode support
• Supports Multicast VLAN Register (MVR)

  Security:

• IEEE 802.1x port-based network access authentication
• MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers for IPv4 and IPv6
• TACACS+ login users access authentication
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Supports DHCP snooping
• Supports ARP inspection
• IP Source Guard prevents IP spoofing attacks
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding

  Management:

• Management IP for IPv4 and IPv6
• Switch Management Interface
• Console/Telnet Command Line Interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure access
• BOOTP and DHCP for IP address assignment
• Firmware upload/download via TFTP or HTTP Protocol for IPv4 and IPv6
• SNTP (Simple Network Time Protocol) for IPv4 and IPv6
• User privilege levels control
• Syslog server for IPv4 and IPv6
• Supports DDM
• Four RMON groups 1, 2, 3, 9 (history, statistics, alarms and events)
• Supports sFlow
• Supports ULDP
• Supports ULPP (Uplink Protection Protocol)
• Supports ULSM (Uplink State Monitor protocol)
• Supports LLDP/LLDP MED
• Supports DHCP Option82, Option37/38
• Supports ping, trace route function for IPv4 and IPv6

• 5 10/100Mbps TP interfaces
• Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX
• IEEE 802.3x flow control for full duplex operation and backpressure for half duplex operation
• Features Store-and-Forward mode with wire-speed filtering and forwarding rates
• Supports 2K absolute MAC address
• Automatic address learning and address aging
• Supports Automatic MDI/MDI-X function
• Full/half-duplex capability on each TX port
• LED indicators for simple diagnostics and management
• FCC Class B, CE compliant

  With concepts of "Easy to install and use", "Compact-sized design", and "Simple troubleshooting", PLANET SW-504 provides cost-conscious business and home users with the foundation of an integrated system of small-office / home-office networking. The SW-504 is a fancy-shaped plastic model, which is just right for your network of 10 to 50 users.   The SW-504 Desktop Fast Ethernet Switch is simple and cost-effective, and offers highly reliable network . And it is the ideal device for bridging Ethernet and Fast Ethernet workgroups or networks. Therefore, PLANET SW-504 switch will be recognized as one of the most important building blocks for today’s networking technology.   To segment the network and ease the network traffic, the 5-port 10/100Mbps is useful for the SOHO switched networks as the friendly network backbone. With LED indicators, the network status can be monitored at a glance.

• 8 10/100Mbps Fast Ethernet ports
• Complies with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-TX Ethernet standards
• Supports auto MDI/MDI-X function

  Switching:

• Hardware-based 10/100Mbps, half / full duplex , flow control and auto-negotiation
• Features Store-and-Forward mode with wire-speed filtering and forwarding rates
• IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
• Integrated address look-up engine, supporting 1K absolute MAC addresses
• Handles up to 1536bytes packet
• Automatic address learning and address aging
• Supports CSMA/CD protocol

  Hardware:

• Made from plastic, desktop size and wall-mount design
• LED indicators for system power, per port Link / Act
• DC, 1A external power adapter
• FCC, CE Class B compliant

  High-speed 10/100Mbps Workgroup Switch: PLANET Fast Ethernet Switch SW-804 provides business and home users with a cost-effective integrated system of small-office / home-office networking. It is with compact-sized plastic case design and just right for the network of 10 to 50 users.   Stable Fast Ethernet Switch Performance: The SW-804 also supports Store-and-Forward forwarding scheme to ensure low latency and high data integrity. The high performance throughput (filtering / forwarding rate: 14,880 packets per second in 10Mbps, and 148,800 packets per second in 100Mbps) and 448K bit packet buffer help the SW-804 to boost bandwidth, eliminate unnecessary traffic, and relieve congestion on your critical server path. With an intelligent address recognition algorithm, the SW-804 could recognize up to a 1K different MAC address and provide 1.6Gbps switching capacity, which makes the SW-804 offer wire-speed packets transfer performance without risk of packet loss.   Flexible Desktop Size Design: The SW-804 is the fancy-shaped plastic model to fit into space-limited environment. With concepts of "Easy to install and use", "Compact sized design", and "Simple troubleshooting", the SW-804 provides cost-conscious business and home users with the foundation from an integrated system of small-office / home-office networking.    Plug & Play and Easy Installation: All RJ-45 copper interfaces in the SW-804 support 10/100Mbps auto-negotiation for optimal speed detection through RJ-45 Category 5/5e cables. Supporting standard for auto-MDI/MDI-X can detect the type of connection to any Ethernet device without requiring special straight or crossover cables. The Flow Control function allows the SW-804 to support routers and servers for direct connection to this switch with fast and reliable data transfer.

• 1x 10/100/1000Mbps Auto-Negotiation RJ45-Port unterstützt Auto-MDI / MDIX
• Automatische Aushandlung des Halbduplex- / Vollduplex-Übertragungsmodus
• Nimmt die WDM-Technologie an und sendet und empfängt Daten auf einer einzigen Faser
• Erweitert die Faserentfernung auf bis zu 20 km

TL-FC311A-20 ist ein Gigabit-Medienkonverter mit einem Gigabit-RJ-45-Anschluss und einem Gigabit-SC-Glasfaseranschluss, der zwischen elektrischen und optischen Signalen konvertieren kann. Die Datenübertragung über große Entfernungen über Glasfaser kann auf kommerzielle Szenarien wie die Überwachung der Parksicherheit und drahtlose Netzwerke angewendet werden. Der TL-FC311A-20 verwendet die WDM-Technologie (Wavelength Division Multiplexing), mit der Daten in einer Entfernung von bis zu 20 km mit nur einer Single-Mode-Glasfaser gesendet und empfangen werden können. Dies spart den Kunden die Hälfte der Kosten für die Kabelbereitstellung. TL-FC311A-20 sendet Daten mit einer Wellenlänge von 1550 nm und empfängt Daten mit einer Wellenlänge von 1310 nm auf einer optischen Faser. Daher sollte das in Verbindung mit dem TL-FC311A-2 verwendete Endgerät Daten mit einer Wellenlänge von 1310 nm senden und Daten mit einer Wellenlänge von 1550 nm empfangen. TP-Link Ein weiterer Medienkonverter TL-FC311B-20 ist eines der Produkte, die mit TL-FC311A-20 zusammenarbeiten können. Außerdem kann dieser Medienkonverter als eigenständiges Gerät (kein Rack erforderlich) oder mit dem TL-FC1420-Rack von TP-Link für Auto-MDI / MDI-X im TX-Port verwendet werden, in dem der Duplexmodus automatisch ausgehandelt wird.

• Complies with the IEEE 802.3, IEEE 802.3u and IEEE 802.3ab Ethernet standards
• 32-port RJ45
• - 16-port 10/100/1000Mbps “Data input”
• - 16-port 10/100/1000Mbps “Data + Power output”One 10/100/1000BASE-T management port

  Power over Ethernet:

• Ultra Power over Ethernet end-span/mid-span PSE
• Up to 60 watts of power on 4-pair UTP
• Backward compatible with IEEE 802.3at/af PD device
• 52V DC, 60-watt PoE power output at maximum on each port
• 600-watt PoE budget
• Auto-detection of IEEE 802.3at/af PoE equipment and device to avoid possible damage by incorrect installation
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m

  PoE Management:

• Per port PoE power schedule
• PoE function enable/disable
• Per port PoE function enable/disable
• PoE port power feeding priority
• PD classification detection
• Over temperature protection
• PD alive check
• PoE schedule

  Management:

• Web interface for remote management
• Supports Network Time Protocol (NTP)
• Firmware upgrade through Web interface
• PLANET Smart Discovery utility automatically finds PLANET devices on the network
• SNMP trap for alarm notification of events
• System log/remote syslog

  Hardware:

• 19-inch rack mountable; 1U height
• Reset button for resetting to default setting and system reboot
• LED indicators for PoE ready and PoE activity
• LED indicators for power alert and fan alert
• LED indicators for PoE power usage status (watts)
• FCC Part 15 Class A, CE

• Complies with the IEEE 802.3, IEEE 802.3u and IEEE 802.3ab Ethernet standards
• 48-port RJ45
• 24-port 10/100/1000Mbps “Data input”
• 24-port 10/100/1000Mbps “Data + Power output”
• One 10/100/1000BASE-T management port

  Power over Ethernet:

• Ultra Power over Ethernet end-span/mid-span PSE
• Up to 60 watts of power on 4-pair UTP
• Backward compatible with IEEE 802.3at/af PD device
• Maximum of 54V DC, 60-watt PoE power output on each port
• 800-watt PoE budget
• Auto-detection of IEEE 802.3at/af PoE equipment and device to avoid possible damage by incorrect installation
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m

  PoE Management:

• Per port PoE power schedule
• PoE function enable/disable
• Per port PoE function enable/disable
• PoE port power feeding priority
• PD classification detection
• Over temperature protection
• PD alive check
• PoE schedule

  Management:

• Web interface for remote management
• Supports Network Time Protocol (NTP)
• Firmware upgrade through Web interface
• PLANET Smart Discovery utility automatically finds PLANET devices on the network
• SNMP trap for alarm notification of events
• System log/remote syslog

  Hardware:

• 19-inch rack mountable; 1U height
• Reset button for resetting to default setting and system reboot
• LED indicators for PoE ready and PoE activity
• LED indicators for power alert and fan alert
• LED indicators for PoE power usage status (watts)
• FCC Part 15 Class A, CE

• 4x 10/100/1G/2.5G/5GBASE-T Gigabit RJ45 interfaces
  • 4-port data + power input
• 4x 10/100/1G/2.5G/5GBASE-T Gigabit RJ45 interfaces
  • 4-port data + power output

Power Information:

• 1 DC power jack for requires +52-54V DC power input
• 100~240V AC, 50/60Hz, 3.33A universal power supply adapter with DC 52V~54V power output 

Power over Ethernet:

• 4-port data + power output
  • Complies with 802.3bt Power over Ethernet Plus Plus end-span and mid-span PSE
  • Backward compatible with IEEE 802.3at Power over Ethernet Plus end-span/mid-span PSE
  • Up to 4 IEEE 802.3at/IEEE 802.3bt PoE devices powered
  • 4 PoE ports with built-in 90-watt 802.3bt PoE++ type 4 PSE or 95-watt PoH PoE injector function
  • 4 PoE ports support 802.3at end-span/mid-span PoE+ 36-watt injector function
  • DIP switch for 802.3bt, PoH and Force mode selection
  • Auto detects powered device (PD)
  • Circuit protection prevents power interference between ports
• Forwards both Ethernet data and PoE power to remote device over a 100-meter (328ft.) distance

 LED Indicators:

• LED indicators for power LED
• LED indicators for per PoE port operation status
• LED indicators for PoE Usage status (50W,100W and 160W) 

Hardware:

• Metal case 
• Wall-mount design and DIN-rail kit (optional)
• 0 to 50 degrees C operating temperature
• FCC Part 15 Class B, CE
• Plug and Play installation 

Standard Compliance:

• IEEE 802.3 Ethernet
• IEEE 802.3u Fast Ethernet
• IEEE 802.3ab Gigabit Ethernet
• IEEE 802.3bz 2.5G/5GBASE-T
• IEEE 802.3af Power over Ethernet 
• IEEE 802.3at Power over Ethernet Plus
• IEEE 802.3bt Power over Ethernet Plus Plus

Compact and Robust 802.3bt PoE++ Network Solution:
PLANET UPOE-400 4-Port Multi-Gigabit 802.3bt PoE++ Injector Hub features four 10/100/1G/2.5G/5GBASE-T 90-watt 802.3bt type-4 PoE++ injector ports. With a total PoE budget of 160 watts, it delivers 802.3bt PoE++ power over Ethernet UTP cables which allow data and power to transmit simultaneously to a remote 802.3bt/at powered device (PD). The UPOE-400 provides a quick, safe and cost-effective 802.3bt PoE++ network solution for small businesses and enterprises. It is designed to perfectly upgrade an existing network infrastructure to 802.3bt PoE++ network system without replacing the existing Ethernet switches and also enables centralization of the power supply. 802.3bt PoE++ Meets High Power Demands of Powered Devices:
As the UPOE-400 adopts the IEEE 802.bt PoE++ standard and PoH technology, it is capable to source up to 90 watts of power by using all the four pairs of standard Cat5e/6 Ethernet cabling to deliver power and full-speed data to each remote PoE compliant PD. It possesses triple amount of power capacity, when compared with that of the conventional 802.3at PoE+. It is an ideal solution to satisfy the growing demand for higher power consuming network PDs, such as:

• PoE PTZ speed dome cameras
• Network devices 
• Thin clients
• AIO (all-in-one) touch PCs, point of sale (POS) and information kiosks
• Remote digital signage displays
• PoE lightings 

Quick and Easy 802.3bt/at PoE Network Deployment:
The UPOE-400 is installed between a regular Ethernet Switch and the PDs. Four ports are network (Ethernet) ports for data input while the other four ports are PoE++ ports for data and power output. Both power and data are transferred simultaneously over the UTP cables to various 802.3bt/at PDs without affecting the existing network performance and functions. With data and Power over Ethernet from one unit, the UPOE-400 can reduce power cable deployment and eliminate the need for dedicated electrical outlets on the wall, ceiling or any unreachable place. Intelligent LED Indicator for Power Input and Real-time PoE Usage:
The UPOE-400 helps users to monitor the current status of power input and PoE power usage easily and efficiently via its advanced LED indication. The “Power LED” allows user to know the status of DC power input. The “PoE Usage” displayed on the front panel of the UPOE-400 has three amber LED indicators of different power usages indicating 50W, 100W and 160W. Via the power usage LED, the UPOE-400 enables the administrator to monitor the status of the power usage of the connected PDs in real time. High Power Budget for PoE Extension:
With up to 90-watt PoE output capability, the UPOE-400 can extend much longer distance by using PLANET PoE Extender for powering up the PoE PD which can be installed over a distance of more than 100 meters. 

• Complies with the IEEE 802.3, IEEE 802.3u and IEEE 802.3ab Ethernet standards
• 16-port RJ45

- 8-port 10/100/1000Mbps “Data input” - 8-port 10/100/1000Mbps “Data + Power output”

• One 10/100/1000BASE-T management port

  Power over Ethernet

• Ultra Power over Ethernet end-span/mid-span PSE
• Up to 60 watts of power on 4-pair UTP
• Backward compatible with IEEE 802.3at/af PD device
• 54V DC, 60-watt PoE power output at maximum on each port
• 400-watt PoE budget
• Auto-detection of IEEE 802.3at/af PoE equipment and device to avoid possible damage by incorrect installation
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m

  PoE Management

• Per port PoE power schedule
• PoE function enable/disable
• Per port PoE function enable/disable
• PoE port power feeding priority
• PD classification detection
• Over temperature protection
• PD alive check
• PoE schedule

  Management

• Web interface for remote management
• Supports Network Time Protocol (NTP)
• Firmware upgrade through Web interface
• PLANET Smart Discovery utility automatically finds PLANET devices on the network
• SNMP trap for alarm notification of events
• System log/remote syslog

  Hardware

• 19-inch rack mountable; 1U height
• Reset button for resetting to default setting and system reboot
• LED indicators for PoE ready and PoE activity
• LED indicators for power alert and fan alert
• LED indicators for PoE power usage status (watts)
• FCC Part 15 Class A, CE

    Gigabit Ultra PoE and PoE+ Network Deployment The UPOE-800G provides the easiest way to power your Ethernet devices such as IP camera on the ceiling and the wireless access point installed on the top of the building. With 8 10/100/1000BASE-T Gigabit Ethernet ports, the UPOE-800G supports full 54V DC power for any remote 60W and IEEE 802.3af/IEEE 802.3at powered device (PD).   To control the power system of your networking devices, the UPOE-800G can directly co-work with network devices such as PoE IP phone to build VoIP telephony network in the office. The Ultra PoE hub can be directly connected to any third-party IEEE 802.3af/802.3at compliant devices installed within 100 meters. Furthermore, the UPOE-800G can extend much longer distance by using PLANET PoE Extender for powering up the PoE PD which can be installed over more than 100 meters away.

- Kosteneffiziente VDSL2 Profil 17a/30a CO / CPE Brückenlösung
nur kompatibel mit VC-201A/204/231 und 234 - Ein-Gehäuse-Design, CO / CPE wählbar über DIP-Schalter
- Definiert einen symmetrischen Bandplan für die Übertragung von Upstream- und Downstream-Signalen
- Entspricht IEEE 802.3, 10Base-T, IEEE 802.3u, 100Base-TX und IEEE 802.3x, Flow control Ethernet
　Normen
- DMT (Diskreter Mehrton) Leitungscodierung
- Halbduplex-Rückdruck und IEEE 802.3x-Vollduplex-Pausenrahmen-Flusskontrolle
- Ein RJ-11-Anschluss für VDSL-Port mit VDSL-Anschluss, zusätzlicher Splitter für POST-Anschluss
- Sprach- und Datenkommunikation können gleichzeitig auf Basis der vorhandenen Telefonleitung genutzt werden
- Ein 10/100Mbps RJ-45 Anschluss, Auto-Negotiation und Auto-MDI/MDI-X
- Unterstützt bis zu 1536 Bytes Paketgröße, IEEE 802.1Q VLAN Tag transparent
- VDSL2 Stand-Alone-Transceiver für einfache Bridge-Modem-Anwendung
- Vorteil der minimalen Installationszeit (einfach als Plug-and-Play)
- Wählbares Zielprofil und Ziel-SNR-Marge
- Unterstützt umfangreiche LED-Anzeigen zur Netzwerkdiagnose
- Arbeitet mit den Media Chassis der PLANET MC-Familie zusammen (MC-700 / MC-1500/ MC-1500R / MC-1500R48)
- Kompakte Größe, einfache Installation
100/100Mbps Downstream / Upstream, Hochleistungs-Ethernet über VDSL Lösung
PLANET VC-231 ist ein Ethernet-over-VDSL2-Konverter mit hoher Leistung. Er wurde auf der Grundlage von zwei zentralen Netzwerktechnologien entwickelt: Ethernet und VDSL2 (Very-high-data-rate Digital Subscriber Line 2). Die VDSL2-Technologie bietet die absolut schnellste Datenübertragungsgeschwindigkeit über bestehende Kupfertelefonleitungen, ohne dass eine Neuverkabelung erforderlich ist. Der VC-231 unterstützt Ultra-High-Performance für das flächendeckende Telefonleitungsnetz mit bis zu 100/100Mbps symmetrischer Datenrate innerhalb von 300m und 50/2Mbps für 1,4km lange Verbindungen.
Implementierung mit bestehenden Telefon-Kupferdrähten
Der VC-231 ist auch ein Long Reach Ethernet (LRE) Konverter mit einem RJ-45 Ethernet Port und einer RJ-11 Telefonbuchse, die für VDSL2 Verbindungen geeignet ist. Mit dem zusätzlichen Splitter aus dem VC-231-Paket kann der Splitter einen POTS-Splitter bereitstellen, um die vorhandene Telefonleitung mit POTS zu teilen; daher ist es nicht notwendig, die vorhandene Kupferleitung zu ersetzen. Stecken Sie den VC-231 mit zusätzlichem Splitter einfach in die vorhandene RJ-11-Telefonbuchse und schon kann ein leistungsstarkes VDSL2-Netz angeschlossen werden. Der VC-231 ist ideal als Ethernet-Extender für ein bestehendes Ethernet-Netzwerk geeignet.
Bereitstellung von anspruchsvollen Servicekonnektivität für ISP-/Triple-Play-Geräte
Der VC-231 bietet eine exzellente Bandbreite, um Triple-Play-Geräte für Home Entertainment und Kommunikation zu bedienen. Mit der Fähigkeit zur symmetrischen Datenübertragung von 100/100Mbps ermöglicht der VC-231 die Nutzung vieler Multimedia-Dienste über das lokale Internet, wie z.B. VOD (Video on Demand), Voice over IP, Videotelefonie, IPTV, Internet-Caching-Server, Fernunterricht und so weiter.
Einfache und flexible Installation
Der Ethernet-over-VDSL2-Konverter verfügt über ein Plug-and-Play-Design und ist vollständig kompatibel mit allen Arten von Netzwerkprotokollen. Darüber hinaus kann der Betriebsstatus jedes einzelnen Ports und des gesamten Systems über die zahlreichen Diagnose-LEDs an der Vorderseite überwacht werden. Der VC-231 bietet zwei Betriebsarten, CPE und CO, für die Anwendung: Der CPE-Modus wird auf der Client-Seite verwendet und der CO-Modus auf der zentralen Seite. Der CPE- oder CO-Modus kann mit Hilfe eines eingebauten DIP-Schalters eingestellt werden. Für Punkt-zu-Punkt-Verbindungen müssen ein VC-231 im CPE-Modus und ein VC-231 im CO-Modus als ein Wandlerpaar eingerichtet werden, um die Verbindung herzustellen.
Hervorragende Upstream- und Downstream-Übertragungsleistung
Der VC-231 definiert auch einen symmetrischen Bandplan für die Übertragung von Upstream- und Downstream-Signalen, der im symmetrischen Modus eine höhere Übertragungsqualität im Nahbereich für die zentrale Seite (CO) bietet. Wenn der VC-231 im Profil 17a betrieben wird, bietet er Langstreckenübertragung mit Ultra-High-Performance für das weitverzweigte Telefonnetz, und wenn der VC-231 im 30a-Betriebsmodus betrieben wird, bietet er Kurzstreckenübertragung mit Upstream- und Downstream-Übertragung mit Wire Speed Performance.

• ITU-T G.993.5 G.vectoring and G.INP
• DMT-based coding technology
• Built-in POST splitter to share voice and date
• CO/CPE mode selectable via DIP switch
• Selectable target band plan and SNR margin
• Up to 150/150Mbps bandwidth (in G.INP, Sym, 8dB mode)
• 1 10/100/1000BASE-TX LAN ports
• Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u, 100BASE-TX and IEEE 802.3x, flow control Ethernet standards
• Half duplex back pressure and IEEE 802.3x full duplex pause frame flow control
• One RJ11 connector for VDSL port with VDSL connection
• Voice and data communication can be shared simultaneously based on the existing telephone wire
• Supports a packet size of up to 9K bytes, IEEE 802.1Q VLAN tag transparency
• VDSL2 standalone transceiver for simple bridge modem application
• Advantage of minimum installation time (Simply by Plug-and-Play)
• Supports extensive LED indicators for network diagnosis
• Co-work with PLANET media converter chassis (MC-700/MC-1500/ MC-1500R/MC-1500R48)
• Compact in size and easy to install

• 1x 1000BASE-X SFP interface
• 1x RJ11 connector for xDSL port with VDSL2 connection

VDSL2 Features:

• VDSL2 stand-alone transceiver for simple bridge modem application
• Cost-effective bridge function to connect two Ethernet LANs
• Up to 150/150Mbps bandwidth (in G.INP, Sym, 8dB mode)
• Voice and data communication can be shared simultaneously based on the existing telephone wire with distance up to 1.4km
• ITU-T G.993.2 VDSL2 standard
• ITU-T G.993.5 G.Vectoring and G.INP
• DMT-based coding technology 
• CO/CPE mode selectable via DIP switch
• Selectable target band plan (symmetric and asymmetric) and SNR margin
• Supports IEEE 802.1Q VLAN tag transparency

Hardware and Installation:

• Compact size, wall-mountable design; ideal solution for space-limited locations
• Advantage of minimum installation time (Simply by Plug and Play)
• Metal case, good for heat sinking
• Supports extensive LED indicators for network diagnosis
• Additional POST splitter to share voice and data
• Supports 6KV DC Ethernet ESD protection

High Performance Gigabit Ethernet over Coaxial Solution: To fulfill the needs of long distance and higher speed required Ethernet over Coaxial applications, PLANET Technology offers a new-generation Ethernet over Coaxial Converter, VC-232G. It features 1 10/100/1000BASE-T RJ45 port and 1 BNC female connector with a compact-sized metal housing, making the placement of the unit convenient. Working well with a pervasive coaxial network, the VC-232G provides an excellent bandwidth of up to a total duplex data rate of 300Mbps which can extend a maximum distance up to 1.4km. It is ideal for extending the distance and signal conversion by transmitting the Ethernet data from the coaxial cable to another 100-meter UTP cable for any type of IP network device such as HD IP camera, wireless access point, NVR and digital signage. Superior Upstream and Downstream Transmission: The VC-232G is based on the two-core networking technology, Gigabit Ethernet and VDSL2 (Very-high-data-rate Digital Subscriber Line 2).  The VC-232G offers a stable yet high-speed point-to-point network access up to a duplex data transmission of 300Mbps. It provides 2 selective transmission modes --  asymmetric mode or symmetric mode -- for the transmission of upstream and downstream signals.

• Asymmetric mode – downstream up to 200Mbps and upstream up to 100Mbps
• Symmetric mode – downstream up to 150Mbps and upstream up to 150Mbps

The symmetric mode provides similar transmission rate on both downstream and upstream. On the other hand, the asymmetric mode performs higher transmission quality in short range. In all, when the VC-232G is in symmetric mode, it provides better upstream performance, and when it is in asymmetric mode, it gives better downstream performance. IP Ethernet over Long Distance Existing Coaxial Cables: The VC-232G is also a Long Reach Ethernet (LRE) solution which provides a quick replacement and smooth migration solution from existing analog system to full digital system. A normal UTP cable can only be extended up to 100 meters, but with the VC-232G, the distance for Ethernet networking can be extended up to 1,400 meters (4,593ft.), which is ideal for the following network applications:

• Long-distance IP network devices
• IP digital signage
• Cable TV to IPTV
• Distance video education
• Electronic billboards
• Other applications

If you have coaxial cable in your existing environment, you can install a pair of the VC-232G very simply without the need to build additional network wires, thus saving costs for network construction. Easy and Flexible Installation: The VC-232G offers two operation modes, the client-side CPE and central-side CO, making any network applications easy and flexible. The CPE or CO mode can be adjusted by using the built-in DIP switch. For point-to-point connection, one VC-232G in CPE mode and the other one in CO mode must be set up as a pair of converters to perform the connection. This enables the administrator to efficiently manage the network over coaxial cable, making long-distance transmission better.

• 1-port 10/100/1000BASE-T RJ45 with IEEE 802.3af/802.3at PoE Injector
• 1 RJ11, connector for xDSL port with VDSL2 or ADSL2+ connection
   

Power over Ethernet:

• Complies with IEEE 802.3at/af PoE Plus end-span PSE
• Supports PoE power up to 30.8 watts per PoE port
• Provides DC 52V power over RJ45 Ethernet cable to PD with Ethernet port
• Auto-detects IEEE 802.3at/af equipment and protects devices from being damaged by incorrect installation
• Remote power feeding up to 100m
• IEEE 802.3at/af splitter devices compatible 

VDSL2 Features:

• VDSL2 stand-alone transceiver for simple bridge modem application
• Cost-effective bridge function to connect two Ethernet LANs
• Point-to-multipoint application: Compatible with PLANET and third-party VDSL2 IP DSLAM for last-mile solution
• Point-to-point application: LAN to LAN extension over phone wire
• Up to 150/150Mbps bandwidth (in G.INP, Sym, 8dB mode)
• Voice and data communication can be shared simultaneously based on the existing telephone wire with distance up to 1.4km
• ITU-T G.993.2 VDSL2 standard
• ITU-T G.993.5 G.Vectoring and G.INP
• DMT-based coding technology 
• CO/CPE mode selectable via DIP switch
• Selectable target band plan (symmetric and asymmetric) and SNR margin
• Supports IEEE 802.1Q VLAN tag transparency

Hardware and Installation:

• Compact size, wall-mountable design; ideal solution for space-limited locations
• Advantage of minimum installation time (Simply by Plug and Play)
• Metal case, good for heat sinking
• Supports extensive LED indicators for network diagnosis
• Additional POTS splitter to share voice and data
• Supports 6KV DC Ethernet ESD protection

PoE Plus High Performance Gigabit Ethernet over Phone Wire Solution: The VC-231GP, a PLANET Long Reach Ethernet (LRE) solution, is a Single-port Gigabit Ethernet-over-VDSL2 Converter with PoE injector function that is installed at a remote location connecting and injecting power to a PoE IP camera, PoE wireless AP, or PoE IP VoIP phone/door phone. It is integrated with three advanced technologies:

• VDSL2/ADSL2+ Digital Subscriber Line technologies
• Gigabit Ethernet
• IEEE 802.3at Power over Ethernet Plus
   

The VC-231GP works with PLANET VDSL2 converters or multiple-channel VDSL2 switches to be able to simultaneously transmit Ethernet data over a distance of up to 1.4km (4,593ft) over phone wire. The VC-231GP forwards the Ethernet data and provides a maximum of 30-watt power output over an additional 100m UTP cable to a remote IP device complied with 802.3af/at PoE PD (powered device) for network deployment. Users have the ability to grow the structure of the current networks simply with even more flexibility. IEEE 802.3at Power over Ethernet Plus: The PoE in-line power following the IEEE 802.3at Power over Ethernet Plus standard makes the VC-231GP able to deliver Gigabit speed Ethernet data and up to 30 watts of power to remote PoE PDs over one Cat.5E/6 Ethernet cable. The VC-231GP provides more flexibility in power requirements for all kinds of PDs at affordable installation costs. 150/150Mbps Downstream/Upstream High Performance Gigabit Ethernet over Phone Wire: Via the latest VDSL2 technology, the VC-231GP offers selectable asymmetric/symmetric band profile capability. It works well with a pervasive telephone line network with a symmetric data rate of up to 150/150Mbps (G.INP, Sym, 8dB) over a distance of 300m and 21/11Mbps over a long distance of 1.4km. PLANET Gigabit Ethernet over VDSL2 series offers absolutely the fastest data transmission speed over the existing copper telephone lines without the need of rewiring.  Versatile, Flexible and Easy Installation: PLANET Gigabit Ethernet-over-VDSL2 converters come with a plug-and-play design. The VC-231GP offers two operation modes, CPE and CO, for application -- CPE mode is used at client side and CO mode is at central side. The CPE or CO mode can be adjusted by using a built-in DIP switch. For point-to-point connection, the VC-231GP in the CPE mode and  the VC-231G or VC-234G in the CO mode must be set up as one pair of converters to perform the connection. It gives administrators the ability to reply a fresh local Intranet in various locations by utilizing the original network structure without additional costs. Stable and Reliable DSL Data Connection: With the integrated support for the ITU-T’s new G.993.5 Vectoring technology, the VC-231GP works in conjunction with vectoring-enabled DSLAMs to remove crosstalk interference and improve maximum line bandwidth across the existing copper infrastructure. Implementing with Existing Telephone System: Use the additional splitter from the package of the VC-231GP to share the existing phone line with POTS, thus replacing the existing copper wiring is not necessary. Just plug the VC-231GP with the additional splitter into the existing RJ11 telephone jack and a high-performance VDSL2 network can be connected. It is ideal for use as an Ethernet extender to an existing Ethernet network.  ADSL2+ Fallback: For those ISPs that still provide ADSL broadband service, the VC-231GP can support transmission rates up to 24Mbps downstream and 1Mbps upstream with the ADSL2+ technology. The VC-231GP establishes a connection with ISP and can be also directly switched over to VDSL2 after the ISP network upgrade.

• ITU-T G.993.5 G.Vectoring and G.INP
• Upstream/Downstream bandwidth up to 200/100Mbps
• CO/CPE mode selectable via DIP switch
• Selectable target band plan and SNR margin
• Half duplex back pressure and IEEE 802.3x full duplex pause frame flow control
• One BNC connector for VDSL connection
• Uses existing RG59/RG6 coaxial cable
• Used in pairs to extend Point-to-Point connection up to 1.4km
• Supports a packet size of up to 1522 bytes, IEEE 802.1Q VLAN tag transparency
• Advantage of minimum installation time (Simply by Plug-and-Play)
• Supports extensive LED indicators for network diagnosis
• Co-work with PLANET media converter chassis (MC-700/MC-1500/ MC-1500R/MC-1500R48)
• Compact in size and easy to install

High Performance Gigabit Ethernet over Coaxial Solution: To fulfill the needs of long distance and higher speed required Ethernet over Coaxial applications, PLANET Technology offers a new-generation Ethernet over Coaxial Converter, VC-232G. It features 1 10/100/1000BASE-T RJ45 port and 1 BNC female connector with a compact-sized metal housing, making the placement of the unit convenient. Working well with a pervasive coaxial network, the VC-232G provides an excellent bandwidth of up to a total duplex data rate of 300Mbps which can extend a maximum distance up to 1.4km. It is ideal for extending the distance and signal conversion by transmitting the Ethernet data from the coaxial cable to another 100-meter UTP cable for any type of IP network device such as HD IP camera, wireless access point, NVR and digital signage. Superior Upstream and Downstream Transmission: The VC-232G is based on the two-core networking technology, Gigabit Ethernet and VDSL2 (Very-high-data-rate Digital Subscriber Line 2).  The VC-232G offers a stable yet high-speed point-to-point network access up to a duplex data transmission of 300Mbps. It provides 2 selective transmission modes --  asymmetric mode or symmetric mode -- for the transmission of upstream and downstream signals.

• Asymmetric mode – downstream up to 200Mbps and upstream up to 100Mbps
• Symmetric mode – downstream up to 150Mbps and upstream up to 150Mbps

The symmetric mode provides similar transmission rate on both downstream and upstream. On the other hand, the asymmetric mode performs higher transmission quality in short range. In all, when the VC-232G is in symmetric mode, it provides better upstream performance, and when it is in asymmetric mode, it gives better downstream performance. IP Ethernet over Long Distance Existing Coaxial Cables: The VC-232G is also a Long Reach Ethernet (LRE) solution which provides a quick replacement and smooth migration solution from existing analog system to full digital system. A normal UTP cable can only be extended up to 100 meters, but with the VC-232G, the distance for Ethernet networking can be extended up to 1,400 meters (4,593ft.), which is ideal for the following network applications:

• Long-distance IP network devices
• IP digital signage
• Cable TV to IPTV
• Distance video education
• Electronic billboards
• Other applications

If you have coaxial cable in your existing environment, you can install a pair of the VC-232G very simply without the need to build additional network wires, thus saving costs for network construction. Easy and Flexible Installation: The VC-232G offers two operation modes, the client-side CPE and central-side CO, making any network applications easy and flexible. The CPE or CO mode can be adjusted by using the built-in DIP switch. For point-to-point connection, one VC-232G in CPE mode and the other one in CO mode must be set up as a pair of converters to perform the connection. This enables the administrator to efficiently manage the network over coaxial cable, making long-distance transmission better.

• Cost-Effective VDSL2 Profile 17a/30a CO / CPE bridge solution • One box design, CO / CPE selectable via DIP Switch • Defines symmetric band plan for the transmission of upstream and downstream signals • Complies with IEEE 802.3, 10Base-T, IEEE 802.3u, 100Base-TX and IEEE 802.3x, Flow control Ethernet 　standards • DMT (Discrete Multi-Tone) line coding • Half duplex Back pressure and IEEE 802.3x Full Duplex Pause frame flow control • Built-in POTS splitter to share voice and data • Two RJ-11 connectors for each VDSL port, one for VDSL connection and one for POST connection • Voice and data communication can be shared simultaneously based on the existing telephone wire • Four 10/100Mbps RJ-45 port, Auto-Negotiation and Auto-MDI/MDI-X • Supports up to 1536 bytes packet size, IEEE 802.1Q VLAN tag transparent • Hardware IGMP Snooping for Multimedia service • VDSL2 stand-alone transceiver for simple bridge modem application • Advantage of minimum installation time (Simply as Plug-and-Play) • Selectable target profile and target SNR margin • Supports extensive LED indicators for network diagnosis   100/100Mbps Downstream / upstream, high Performance Ethernet over VDSL Solution PLANET VC-234 is an Ethernet-over-VDSL2 Bridge with high performance. It is designed based on two core networking technology, Ethernet and VDSL2 (Very-high-data-rate Digital Subscriber Line 2). The VDSL2 technology offers absolutely fastest data transmission speed over existing copper telephone lines without the need of rewiring. The VC-234 supports ultra-high performance to the pervasive telephone line network with up to 100/100Mbps symmetric data rate within 300m and 20/4Mbps for 1.4km long range connections.     Implementing with Existing Telephone Copper Wires The VC-234 is also a Long Reach Ethernet (LRE) Bridge providing four RJ-45 Ethernet ports and two RJ-11 phone jacks, in which one is for VDSL connection and the other one is for POTS (Plain Old Telephone Service) connection. The VC-234 has built-in POTS splitter to share the existing phone line with POTS; therefore it is no need of replacing the existing copper wiring. Just plug the VC-234 into the existing RJ-11 telephone jack and a high-performance VDSL2 network can be connected. The VC-234 is ideal to be used as an Ethernet extender to an existing Ethernet network.   Delivering High-Demand Service Connectivity for ISP / Triple Play Devices The VC-234 provides excellent bandwidth to satisfy the triple play devices for home entertainment and communication. With the capability of 100/100Mbps symmetric data transmission, the VC-234 enables many multi-media services to work on the local Internet, such as VOD (Video on Demand), Voice over IP, Video phone, IPTV, Internet caching server, distance education, and so on.   Easy & Flexible Installation The Ethernet-over-VDSL2 Bridge comes with a plug-and-play design and is fully compatible with all kinds of network protocols. Moreover, the operating status of each individual port and the whole system can be watched via the rich diagnostic LEDs on the front panel. The VC-234 offers two modes, CPE and CO, for application: CPE mode is used at client side and CO mode is at central side. The CPE or CO mode can be adjusted by using a built-in DIP switch. For point-to-point connection, a CPE mode VC-234 and a CO mode VC-234 must be setup as one pair of converters to perform the connection.   Providing Superior Upstream and Downstream Transmission Performance The VC-234 also defines symmetric band plan for the transmission of upstream and downstream signals; the band plan performs higher transmission quality in short range for central side (CO) in symmetric mode. In all, when the VC-234 is in profile 17a operation mode, it provides long distance transmit with Ultra-high performance to the pervasive telephone line network, and when the VC-234 is in 30a operation mode, it gives short distance transmits with upstream and downstream transmission giving wire speed performance.

• ITU-T G.993.5 G.Vector and G.INP
• DMT-based coding technology
• Built-in POST splitter to share voice and date
• One RJ11 connector for VDSL port with VDSL connection
• One phone connector for telephone connection
• Voice and data communication can be shared simultaneously based on the existing telephone wire
• CO/CPE mode selectable via DIP switch
• Selectable target band plan and SNR margin
• Up to 200/100Mbps (G.INP, Asym, 8dB) bandwidth
• 4 10/100/1000BASE-TX LAN ports
• Complies with IEEE 802.3, 10BASE-T, IEEE 802.3u, 100BASE-TX and IEEE 802.3x, flow control Ethernet standards
• Half duplex back pressure and IEEE 802.3x full duplex pause frame flow control
• Supports IEEE 802.1Q VLAN tag transparency
• VDSL2 stand-alone transceiver for simple bridge modem application
• Advantage of minimum installation time (Simply Plug-and-Play)
• Supports extensive LED indicators for network diagnosis
• Compact in size and easy to install

High Performance Gigabit Ethernet over Phone Wire Solution:
PLANET VC-234G, a new-generation and high-performance Gigabit Ethernet-over-VDSL2 Converter, works well with a pervasive telephone line network with a symmetric (downstream/upstream) data rate of up to 150/150Mbps (G.INP, Sym, 8dB) over a distance of 300m and 20/12Mbps over a long distance of 1.4km. It is based on the two-core networking technology, Gigabit Ethernet and VDSL2 (Very-high-data-rate Digital Subscriber Line 2). The VDSL2 technology offers absolutely the fastest data transmission speed over the existing copper telephone lines without the need of rewiring.
With integrated support for the ITU-T’s new G.993.5 vectoring technology, the VC-234G works in conjunction with vectoring-enabled DSLAMs to remove crosstalk interference and improve maximum line bandwidth across the existing copper telephone infrastructure. Implementing with Existing Telephone Copper Wires:
The VC-234G is also a Long Reach Ethernet (LRE) Bridge providing four RJ45 Ethernet ports and two RJ11 phone jacks, in which one is for VDSL connection and the other one is for POTS (Plain Old Telephone Service) connection. The VC-234G has a built-in POTS splitter to share the existing phone line with POTS; therefore, there is no need to replace the existing copper wiring. Just plug the VC-234G into the existing RJ11 telephone jack and a high-performance VDSL2 network can be connected. The VC-234G is ideal to be used as an Ethernet extender to an existing Ethernet network. Delivering High-demand Service Connectivity for ISP/Triple Play Devices:
The VC-234G provides excellent bandwidth to satisfy the triple play devices for home entertainment and communication. With the capability of 200/100Mbps (G.INP, Asym, 8dB) asymmetric data transmission, the VC-234G enables many multi-media services to work on the local Internet, such as VoD (video on demand), voice over IP, video phone, IPTV, Internet caching server, distance education, and so on. Easy and Flexible Installation:
The Ethernet-over-VDSL2 Converter comes with a Plug-and-Play design and is fully compatible with all kinds of network protocols. Moreover, the operating status of each individual port and the whole system can be watched via the rich diagnostic LEDs on the front panel. The VC-234G offers two modes, CPE and CO, for application -- CPE mode is used at client side and CO mode is at central side. The CPE or CO mode can be adjusted by using a built-in DIP switch. For the point-to-point connection, a CPE mode and a CO mode must be set up as one pair of converters to perform the connection.   ADSL2+ Fallback
For those ISPs that still provide ADSL broadband service, the VC-234G can support a downstream rate of up to 24Mbps and an upstream rate of 1Mbps with the ADSL2+ technology. The VC-234G can also be directly switched over to VDSL2 after the network upgrade.

• 4x 10/100BASE-TX RJ45 LAN ports, auto-negotiation, auto MDI/MDI-X
• 1x 10/100BASE-TX RJ45 WAN port, auto-negotiation, auto MDI/MDI-X
• 1x 4G LTE 2.3 dBi antenna
• 2x 2.4G WiFi 2dBi antennas
• 1x GPS antenna
• 1x SIM card slot
• 1x console port
• 2x TF card slots  to save files for Wi-Fi advertising

Cellular Interface:

• Supports multi-band connectivity with FDD LTE/ TDD LTE/ WCDMA/ GSM/ LTE Cat4
• Built-in SIM and broadband backup for network redundancy
• One detachable antenna for 4G LTE connection
• LED indicators for connection status (3G/4G)

Wi-Fi Interfaces:

• Complies with IEEE 802.11b/g/n 2.4GHz
• Two detachable antennas for wireless connection
• 64-/128-bit WEP, WPA/WPA2 and WPA-PSK/WPA2-PSK (TKIP/AES encryption),
• LED indicators for status 

Case and Installation:

• IP30 metal case
• Mounting brackets for vehicles
• Power requirement: 6~32V DC
• Supports 15KV DC Ethernet ESD protection
• -25 to 65 degrees C operating temperature 

Advanced Features:

• Supports demilitarized zone (DMZ).
• Supports VPN client, including GRE, PPTP, IPSec, L2TP 
• Supports NAT port mapping function, such as SNAT, DNAT
• Supports Static Routing to display current routing information of the gateway
• Supports QoS for bandwidth management
• Supports Dynamic DNS and PLANET DDNS
• Supports WAN connection types: DHCP client, static IP and PPPoE client
• Secures network connection
  
  • IP filter
  • URL filter
  • MAC filter 

Management:

• Gateway management interfaces
  
  • Console/Telnet Command Line interface 
  • Web  management
• Gateway Maintenance
  
  • Firmware upload via HTTP, TFTP
  • Restore or Reset button for reset to factory default
  • Dual images
• SNTP (Simple Network Time Protocol)
  System log
• System tool, such as ping and trace 
• Configuration backup and restore
• Supports CMS (Central Management System) and Wifidog for remote management and  Wi-Fi advertising

Internet of Vehicles via 4G LTE Cellular Gateway:
PLANET VCG-1500WG-LTE is a reliable, secure and high-bandwidth communications vehicle cellular gateway for demanding mobile applications and IoV (Internet of Vehicles) deployments. It features 4G LTE (Long Term Evolution), wireless AP, five Ethernet ports (4 LAN and 1 WAN), GPS,  VPN technology and bandwidth management bundled in a mountable metal case to establish a public network connection and allows passengers to access Internet. High-performance 4G LTE :
The VCG-1500WG-LTE is able to reach a download (DL) speed of up to 100Mbps and an upload (UL) speed of 50Mbps. The Cellular Gateway also supports multi-band connectivity including LTE FDD, TDD, HSDPA, WCDMA and GSM for a wide range of applications.  Wireless Access Point:
With an integrated 802.11n Wireless Access Point, the gateway supports data rate up to 300Mbps and is also compatible with 2.4GHz 802.11b/g/n equipment. The Wireless Protected Access (WPA-PSK/WPA2-PSK) and Wireless Encryption Protocol (WEP) features enhance the level of transmission security and access control over Wireless LAN.  GPS Included:
The VCG-1500WG-LTE is equipped with one convenient feature and that is GPS (global positioning system). It is a positioning system based on a network of satellites that continuously transmit necessary data. More signals transmitted from more satellites can triangulate its location on the ground, meaning any location can be easily tracked anytime.  Cost-effective VPN Solution:
The VCG-1500WG-LTE provides a complete data security and privacy feature for access and exchange of sensitive data. The full VPN capability of the VCG-1500WG-LTE including built-in PPTP, LT2P, and IPSec VPN client functions with DES/3DES/AES encryption and MD5/SHA-1 authentication makes the shared connection more secure and flexible. The IPSec VPN also makes the private tunnel over Internet more secure for enterprises doing business transactions. Dual TF Cards for Wi-Fi Advertising Contents:
The VCG-1500WG-LTE provides dual TF cards and the capacity of each card is up to 128GB. The TF cards can store thousands of advertising data and movie files. The administrator is able to upload these files to TF cards via FTP locally. Besides, through CMS (Central Management System), administrator is able to upload and maintain these files remotely. The device will display advertising contents when users access to the Wi-Fi after authentication.  Superior Management Functions:
For networking management features, the VCG-1500WG-LTE provides such functions as  DMZ, QoS and Wifidog, as well as full secure functions including Network Address Translation (NAT), IP/URL/MAC filtering. The VCG-1500WG-LTE has 4G and WAN connection failover characteristics, which can automatically switch over to the redundant, stable WAN connection to keep users always online without missing any fascinating moments. User-friendly and Secure Management:
For efficient management, the VCG-1500WG-LTE is equipped with console, web and Wifidog management interfaces. With the built-in web-based management interface, the VCG-1500WG-LTE offers an easy-to-use, platform independent management and configuration facility. The VCG-1500WG-LTE supports Wifidog and it can be managed via CMS (Central Management System) for remote management and Wi-Fi advertising. 

• Compliant with hybrid video (AHD/TVI/CVI/CVBS)
• Long-distance data transmission of 20km
• Status indication for power supply, optical signal and video
• High-speed synchronous digital transmission technology
• Guarantees safe transmission under poor electromagnetic environment
• Video and data transmission over Gigabit fiber optic cable
• PAL, NTSC, SECAM compatible
• Data type: RS485
• 8-/10-bit digital Video Signal sampling
• Standalone or work with PLANET MC-700/1500/1500R media converter chassis
• Compact size, wall-mount design, easy installation

  Long Distance Analog Surveillance Transmission System: To deploy AHD/CVI/TVI/CVBS analog camera in a remote place efficiently and provide high video quality and reliable signal, PLANET has developed the video over Gigabit fiber media converter kit, VF-101G-KIT, which is ideal for extending the distance and signal conversion by transmitting the AHD/CVI/TVI/CVBS video and data over the fiber-optic cable. Adopting the intelligent encoding/decoding technology and with the compact box, the VF-101G-KIT video over fiber media converter enables videos to be delivered in high quality over a distance of up to 20km long.

• Compliant with hybrid video (AHD/TVI/CVI/CVBS)
• Long-distance data transmission of 20km
• Status indication for power supply, optical signal and video
• High-speed synchronous digital transmission technology
• Guarantees safe transmission under poor electromagnetic environment
• Video and data transmission over Gigabit fiber optic cable
• PAL, NTSC, SECAM compatible
• Data type: RS485
• 8-/10-bit digital Video Signal sampling
• Standalone or work with PLANET MC-700/1500/1500R media converter chassis
• Compact size, wall-mount design, easy installation

• Compliant with hybrid video (AHD/TVI/CVI/CVBS)
• Long-distance data transmission of 20km
• Status indication for power supply, optical signal and video
• High-speed synchronous digital transmission technology
• Guarantees safe transmission under poor electromagnetic environment
• Video and data transmission over Gigabit fiber optic cable
• PAL, NTSC, SECAM compatible
• Data type: RS485
• 8-/10-bit digital Video Signal sampling
• Standalone or work with PLANET MC-700/1500/1500R media converter chassis
• Compact size, wall-mount design, easy installation

Long Distance Analog Surveillance Transmission System:
To deploy AHD/CVI/TVI/CVBS analog camera in a remote place efficiently and provide high video quality and reliable signal, PLANET has developed the video over Gigabit fiber media converter kit, VF-101G/102G/106G-KIT, which is ideal for extending the distance and signal conversion by transmitting the AHD/CVI/TVI/CVBS video and data over the fiber-optic cable. Adopting the intelligent encoding/decoding technology and with the compact box, the VF-101G/102G/106G-KIT video over fiber media converter enables videos to be delivered in high quality over a distance of up to 20km long. Fiber Optic Communication for Video and Serial Data:
This Video over Gigabit Fiber Converter kit consists of a Video Transmitter and a Video Receiver:

• VF-101G/102G/106G-T: 1-channel Video over Gigabit Fiber Transmitter
• VF-101G/102G/106G-R: 1-channel Video over Gigabit Fiber Receiver

The VF-101G/102G/106G-KIT is a digital fiber-optic transmission system that brings users a cost-effective solution for transmission of 1 channel uncompressed digital video and one reverse RS485 async data over one single fiber cable. The VF-101G/102G/106G-KIT is an adjustable free device providing high-quality and real-time video transmission. It can be widely used in intelligent transportation systems (ITS), traffic surveillance, security monitoring, automation control, intelligent residential districts, etc. Easy Installation:
Simply by Plug and Play, the installation of the VF-101G/102G/106G-KIT media conversion is quite easy. They can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter Chassis (MC-700, MC-1500 and MC-1500R). When working with the media converter chassis, the media converter chassis provides DC power to VF-101G/102G/106G-T or VF-101G/102G/106G-R to maintain the video over fiber-optic transmission system at the central location.

• Compliant with hybrid video (AHD/TVI/CVI/CVBS)
• 20km long-distance data transmission
• Fiber optic transmission of four video signals on one fiber with RS485 data signals which may be one way with the video or optional duplex
• Effective against electromagnetic interference, radio frequency interference, 6KV high-level lightning protection design
• Video bandwidth of 60MHz, SNR>67dB
• Wide temperature range from -20 to 70 degrees C

 

• High-speed synchronous digital transmission up to 20km
• Fiber optic transmission of four video signals on one fiber with RS-485 data signals
• Friendly status indication for power supply, optical signal and video
• No electromagnetic interference, radio frequency interference and ground current
• Guarantees safe transmission under poor electromagnetic environment
• Maximum tolerable link loss for single mode fiber is 18db
• Video bandwidth of 6.5 MHz, SNR > 63dB
• Industrial level of operating under a wide temperature range of -25 to 75 degrees C

  Reliable Long Distance Solution for Analog Surveillance System To help current analog camera deployment in long distances efficiently and provide high video quality and reliable signal, PLANET has developed the video over fiber media converter kit, VF-402-KIT, which is ideal for extending the distance and signal conversion by transmitting the video and data over the fiber-optic cable. Applying the intelligent encoding / decoding technology and with the compact box, the VF-402-KIT CCTV over fiber media converter enables the videos to be delivered in high quality up to 20km long in distance.    Fiber Optic Communication for Video and Serial Data The VF-402-KIT consists of a Video Transmitter and a Video Receiver: 　

• VF-402-T: 4-Channel Video over Fiber Transmitter
• VF-402-R: 4-Channel Video over Fiber Receiver

  It is a digital fiber-optic transmission system to bring users a cost-effective solution for transmission of 4-channel uncompressed digital video and one reverse RS-485 async-data over one single fiber cable. The VF-402-KIT is an adjustable free device, providing high quality and real-time video transmission. It can be widely used in intelligent transportation systems (ITS), traffic surveillance, security monitoring, automation control, intelligent residential districts, etc.    Industrial Level Monitoring Systems The VF-402-KIT can be applied to Industrial level operation under a wide temperature range of -25 to 75 degrees C. It performs zero distortion of high quality video transmission and clear graphics in long distance by adopting advanced international uncompressed full digital error correction and gigabit fiber optical transmission technology. This series of optical transceiver supports hot plug and can be deployed independently or in rack-mounted structure. It is simple to operate without requiring field adjustment. Therefore, the VF-402-KIT is very applicable to different working environments.  

• 5x 10/100/1000BASE-T RJ45 ports
• 1y undefined Ethernet port (LAN/WAN)
• Dual-WAN function
• 1x USB 3.0 port for system configuration backup and restore
• Reset button
• Desktop installation or rack mounting (optional)
• Fanless design   

IP Routing Feature:

• Static Route
• Dynamic Route 

Firewall Security:

• Stateful Packet Inspection (SPI) firewall
• Blocks DoS/DDoS attack 
• Content filtering
• MAC/IP filtering
• Blocks SYN/ICMP flooding  

VPN Features:

• IPSec (Host to Host)/GRE/PPTP server/L2TP/SSL(Open VPN) 
• Max. Connection Tunnel Entries: 60 VPN tunnels,
• Encryption methods: DES, 3DES, AES, AES-128/192/256
• Authentication methods: MD5, SHA-1, SHA-256, SHA-384, SHA-512 

Networking:

• Outbound load balancing
• Failover for dual-WAN
• Static IP/DHCP client for WAN
• Protocols: TCP/IP, UDP, ARP, IPv4, IPv6
• Port forwarding
• DMZ
• SNMP
• DHCP server/NTP client 
• MAC address clone
• DDNS: PLANET DDNS, PLANET Easy DDNS,
• DynDNS and No-IP
• Cybersecurity 

Others:

• Setup wizard
• Dashboard for real time system overview
• Supported access by HTTP or HTTPS
• Auto reboot
• PLANET Smart Discovery utility/UNI-NMS supported

Powerful Network  Security Solution:
The innovation of the Internet has created tremendous worldwide opportunities for e-business and information sharing. It has become essential for businesses to focus more on network security issues. The demand for information security has become the primary concern for the enterprises. To fulfill this demand, PLANET has launched the VR-100 VPN Security Router, an all-in-one appliance that carries several main categories across your network security deployments: SPI firewall security protection, policy auditing (Content Filtering, VPN Tunnel and MAC/IP Filtering), and easy management (Setup Wizard, DHCP Server and Dashboard). Furthermore, its Dual-WAN Failover and Outbound Load Balance features can improve the network efficiency while the web-based interface provides friendly and consistent user experience.  Excellent Ability in Threat Defense:
The VR-100 built-in SPI (Stateful Packet Inspection) firewall and Blocking DoS/DDoS attack functions provide high efficiency and extensive protection for your network. Virtual Server and DMZ functions can let you setup servers in the Intranet and still provide services to the Internet users. Ideal VPN Security Router Solution for SMBs:
The VR-100 provides complete data security and privacy for accessing and exchanging most sensitive data, built-in IPSec VPN function with DES/3DES/AES encryption and MD5/SHA-1/SHA-256/SHA-384/SHA-512 authentication, and GRE, SSL, PPTP and L2TP server mechanism. The full VPN capability in the VR-100 makes the connection solid secure, more flexible, and more capable. The VR-100 supports many popular security features including Content Filterring to block specific URL, MAC/IP filtering, outbound load-balancing and more. Furthermore, it provides higher performance with all Gigabit Ethernet interfaces which offer faster speeds for your network applications. The Gigabit user-defined interfaces flexibly fulfill the network requirement nowadays, and the Dual-WAN interfaces enable the VR-100 to support outbound load balancing and WAN fail-over features. Cybersecurity Network Solution to Minimize Security Risks:
The cybersecurity feature included to protect the switch management in a mission-critical network virtually needs no effort and cost to install. For efficient management, the VR-100 is equipped with HTTPS web and SNMP management interfaces. With the built-in web-based management interface, the VR-100 offers an easy-to-use, platform independent management and configuration facility. The VR-100 supports SNMP and it can be managed via any management software based on the standard SNMP protocol. Improving Network Efficiency:
The VR-100 has link redundancy, Content Filtering and many more functions to make the entire network system better. It is applicable to the small-scale sector (from 10 to 50 people), using a 9-inch desktop design, with five Gigabit ports (WAN/LAN). The VR-100’s economical price with complete cable management features make it an inevitable choice for the next-generation office network load balancer. The VR-100’s built-in Content Filtering feature can automatically resolve the IP address corresponding to all. Users’ network can be easily managed by just typing the URL of the websites  like Facebook, YouTube and Yahoo. The VR-100 can connect dual WANs with up to two different ISPs. It creates a stable and qualified VPN connection for many important applications such as VoIP, video conferencing and data transmission.

• Dual-WAN failover and Dual-WAN load balancing
• SSL VPN and robust hybrid VPN (IPSec/PPTP/L2TP over IPSec)
• Stateful Packet Inspection (SPI) firewall and content filtering
• Blocks DoS/DDOS attack, port range forwarding
• High Availability, AP Controller, Captive Portal and RADIUS
• IPv6, SNMP, PLANET DDNS and Universal Network Management System 

Hardware:

• 5x 10/100/1000BASE-T RJ45 ports
• 1x undefined Ethernet port (LAN/WAN) for Dual-WAN function
• 1x USB 3.0 port for system configuration backup and restore
• Reset button and Fanless design
• Desktop installation or rack mounting  

IP Routing Feature:

• Static Route
• Dynamic Route
• OSPF 

Firewall Security:

• Cybersecurity
• Stateful Packet Inspection (SPI) firewall
• Blocks DoS/DDoS attack 
• Content Filtering
• MAC Filtering and IP Filtering
• NAT ALGs (Application Layer Gateway)
• Blocks SYN/ICMP Flooding  

VPN Features:

• IPSec/Remote Server (Net-to-Net, Host-to-Net), GRE, PPTP Server, L2TP Server, SSL Server/Client (Open VPN)
• Max. Connection Tunnel Entries: 60 VPN tunnels,
• Encryption methods: DES, 3DES, AES, AES-128/192/256
• Authentication methods: MD5, SHA-1, SHA-256, SHA-384, SHA-512 

Networking:

• Outbound load balancing
• Failover for dual-WAN
• High Availability
• Captive Portal
• RADIUS Server/Client
• Static IP/PPPoE/DHCP client for WAN
• DHCP server/NTP client for LAN
• Protocols: TCP/IP, UDP, ARP, IPv4, IPv6
• Port forwarding, QoS, DMZ, IGMP, UPnP,SNMPv1,v2c, v3
• MAC address clone
• DDNS: PLANET DDNS, Easy DDNS, DynDNS and No-IP 

Others:

• Setup wizard
• Dashboard for real-time system overview
• Supported access by HTTP or HTTPS
• Auto reboot
• PLANET Smart Discovery utility/UNI-NMS supported

Powerful VPN Security Solution:
The innovation of the Internet has created tremendous worldwide opportunities for e-business and information sharing. It has become essential for businesses to focus more on network security issues. The demand for information security has become the primary concern for the enterprises. To fulfill this demand, PLANET has launched the VR-300 VPN Security Router, an all-in-one appliance that carries several main categories across your network security deployments: Cyber Security, SPI firewall security protection, policy auditing (Content Filtering, VPN Tunnel and MAC/IP Filtering), AP Controller, Captive Portal, RADIUS and easy management (Setup Wizard, DHCP Server and Dashboard). Furthermore, its Dual-WAN Failover, Outbound Load Balance and High-Availability features can improve the network efficiency while the web-based interface provides friendly and consistent user experience. Wi-Fi Deployments and Authentication with Simplified Management:
The VR-300 also provides a built-in AP Controller, Captive Portal, RADIUS and a DHCP server to facilitate small and medium businesses to deploy secure employee and guest access services without any additional server. The VR-300 can offer a secure Wi-Fi network with easy installation for your business. Centralized Remote Control of Managed APs*:
The VR-300 provides centralized management of PLANET Smart AP series via a user-friendly Web GUI. It's easy to configure AP for the wireless SSID, radio band and security settings. With a four-step configuration process, different purposes of wireless profiles can be simultaneously delivered to multiple APs or AP groups to minimize deployment time, effort and cost. For example, to configure multiple Smart APs of the same model, the VR-300 allows clustering them to a managed group for unified management. According to requirements, wireless APs can be flexibly expanded or removed from a wireless AP group at any time. The AP cluster benefits bulk provision and bulk firmware upgrade through single entry point instead of having to configure settings in each of them separately. Ideal High-Availability VPN Security Router Solution for SMBs:
The VR-300 provides complete data security and privacy for accessing and exchanging most sensitive data, built-in IPSec VPN function with DES/3DES/AES encryption and MD5/SHA-1/SHA-256/SHA-384/SHA-512 authentication, and GRE, SSL, PPTP and L2TP server mechanism. The full VPN capability in the VR-300 makes the connection secure, more flexible, and more capable. Excellent Ability in Threat Defense:
The VR-300’s built-in SPI (stateful packet inspection) firewall and DoS/DDoS attack mitigation functions provide high efficiency and extensive protection for your network. Thus, virtual server and DMZ functions can let you set up servers in the Intranet and still provide services to the Internet users. Cybersecurity Network Solution to Minimize Security Risks:
The cybersecurity feature included to protect the switch management in a mission-critical network virtually needs no effort and cost to install. For efficient management, the VR-300 is equipped with HTTPS web and SNMP management interfaces. With the built-in web-based management interface, the VR-300 offers an easy-to-use, platform independent management and configuration facility. The VR-300 supports SNMP and it can be managed via any management software based on the standard SNMP protocol.

• Dual-WAN failover and Dual-WAN load balancing
• SSL VPN and robust hybrid VPN (IPSec/PPTP/L2TP over IPSec)
• Stateful Packet Inspection (SPI) firewall and content filtering
• Blocks DoS/DDOS attack, port range forwarding
• High Availability, AP Controller, Captive Portal and RADIUS
• IPv6, SNMP, PLANET DDNS and Universal Network Management System 
• Compliant with the IEEE 802.3at PoE+ with PD alive check/schedule management

Hardware:

• 5x 10/100/1000BASE-T RJ45 ports with 4-port IEEE 802.3at PoE+ injector function
• 1x undefined Ethernet port (LAN/WAN) for Dual-WAN function
• 1x USB 3.0 port for system configuration backup and restore
• Reset button and Fanless design
• Desktop installation or rack mounting  

Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus, end-span PSE
• Backward compatible with IEEE 802.3af Power over Ethernet
• Up to 4 ports of IEEE 802.3af / 802.3at devices powered
• Supports PoE power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• PoE management
  
  • Total PoE power budget control
  • Per port PoE function enable/disable
  • PoE port power feeding priority
  • Per PoE port power limitation
  • PD classification detection
  • PD alive check
  • PoE schedule

IP Routing Feature:

• Static Route
• Dynamic Route
• OSPF 

Firewall Security:

• Cybersecurity
• Stateful Packet Inspection (SPI) firewall
• Blocks DoS/DDoS attack 
• Content Filtering
• MAC Filtering and IP Filtering
• NAT ALGs (Application Layer Gateway)
• Blocks SYN/ICMP Flooding  

VPN Features:

• IPSec/Remote Server (Net-to-Net, Host-to-Net), GRE, PPTP Server, L2TP Server, SSL Server/Client (Open VPN)
• Max. Connection Tunnel Entries: 60 VPN tunnels,
• Encryption methods: DES, 3DES, AES, AES-128/192/256
• Authentication methods: MD5, SHA-1, SHA-256, SHA-384, SHA-512 

Networking:

• Outbound load balancing
• Failover for dual-WAN
• High Availability
• Captive Portal
• RADIUS Server/Client
• Static IP/PPPoE/DHCP client for WAN
• DHCP server/NTP client for LAN
• Protocols: TCP/IP, UDP, ARP, IPv4, IPv6
• Port forwarding, QoS, DMZ, IGMP, UPnP,SNMPv1,v2c, v3
• MAC address clone
• DDNS: PLANET DDNS, Easy DDNS, DynDNS and No-IP 

Others:

• Setup wizard
• Dashboard for real-time system overview
• Supported access by HTTP or HTTPS
• Auto reboot
• PLANET Smart Discovery utility/UNI-NMS supported

Powerful VPN Security Solution:
The innovation of the Internet has created tremendous worldwide opportunities for e-business and information sharing. It has become essential for businesses to focus more on network security issues. The demand for information security has become the primary concern for the enterprises. To fulfill this demand, PLANET has launched the VR-300 VPN Security Router, an all-in-one appliance that carries several main categories across your network security deployments: Cyber Security, SPI firewall security protection, policy auditing (Content Filtering, VPN Tunnel and MAC/IP Filtering), AP Controller, Captive Portal, RADIUS and easy management (Setup Wizard, DHCP Server and Dashboard). Furthermore, its Dual-WAN Failover, Outbound Load Balance and High-Availability features can improve the network efficiency while the web-based interface provides friendly and consistent user experience. Wi-Fi Deployments and Authentication with Simplified Management:
The VR-300 also provides a built-in AP Controller, Captive Portal, RADIUS and a DHCP server to facilitate small and medium businesses to deploy secure employee and guest access services without any additional server. The VR-300 can offer a secure Wi-Fi network with easy installation for your business. Centralized Remote Control of Managed APs*:
The VR-300 provides centralized management of PLANET Smart AP series via a user-friendly Web GUI. It's easy to configure AP for the wireless SSID, radio band and security settings. With a four-step configuration process, different purposes of wireless profiles can be simultaneously delivered to multiple APs or AP groups to minimize deployment time, effort and cost. For example, to configure multiple Smart APs of the same model, the VR-300 allows clustering them to a managed group for unified management. According to requirements, wireless APs can be flexibly expanded or removed from a wireless AP group at any time. The AP cluster benefits bulk provision and bulk firmware upgrade through single entry point instead of having to configure settings in each of them separately. Ideal High-Availability VPN Security Router Solution for SMBs:
The VR-300 provides complete data security and privacy for accessing and exchanging most sensitive data, built-in IPSec VPN function with DES/3DES/AES encryption and MD5/SHA-1/SHA-256/SHA-384/SHA-512 authentication, and GRE, SSL, PPTP and L2TP server mechanism. The full VPN capability in the VR-300 makes the connection secure, more flexible, and more capable. Excellent Ability in Threat Defense:
The VR-300’s built-in SPI (stateful packet inspection) firewall and DoS/DDoS attack mitigation functions provide high efficiency and extensive protection for your network. Thus, virtual server and DMZ functions can let you set up servers in the Intranet and still provide services to the Internet users. Cybersecurity Network Solution to Minimize Security Risks:
The cybersecurity feature included to protect the switch management in a mission-critical network virtually needs no effort and cost to install. For efficient management, the VR-300 is equipped with HTTPS web and SNMP management interfaces. With the built-in web-based management interface, the VR-300 offers an easy-to-use, platform independent management and configuration facility. The VR-300 supports SNMP and it can be managed via any management software based on the standard SNMP protocol.

• Compliant with IEEE 802.11n 2T2R MIMO with backward compatible with 802.11a/b/g standard
• Simultaneous 2.4GHz and 5GHz wireless connectivity
• Equipped with Gigabit LAN and 600Mbps wireless connectivity (Dual-N Band)
• IPv4 and IPv6 dual-stack management networks

  Radio and Outdoor Characteristics:

• Built-in 4 N-Type (Female) antenna connectors
• High output power of up to 500mW with multiple adjustable transmit power control
• Built-in surge arrester and ground terminal for protection against lightning strikes
• IP66 aluminum case
• IEEE 802.3at PoE design
• Wide operating temperature of -40 ~ 70 degrees C

  Wireless Characteristics:

• Dual-N band performs backhaul WDS link at 5GHz and relay wireless signal at 2.4GHz
• Multiple wireless modes: AP, WDS PtP and WDS PtMP
• Supports up to 16 multiple-SSIDs at each frequency band
• Multicast rate adaptation guarantees wireless bandwidth and service quality
• Automatic ACK timeout detection for long-range connection

  Secure and Highly-reliable Network Management:

• Advanced 128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK(TKIP/AES) security, and 802.1x authentication
• Supports IEEE 802.1Q tagged VLAN over WDS or mapping up to 32 SSIDs
• Dual-image (dual-OS) backup mechanism
• Easy Web-based UI and PLANET Smart Discovery supported
• Telnet command line interface
• Auto power saving mode reduces power consumption by 30%
• Easily locate online clients’ information through the Wireless Location Management
• System status monitoring includes statistics and associated client list

• 4x 10/100/1000BASE-T RJ45 ports
• 1x 10/100/1000BASE-T RJ45 WAN port or LAN port ( router mode/switch mode) 

Industrial Case and Installation:

• Compact size with fixed wall mounting, magnetic wall mounting or DIN-rail design
• IP30 metal case 
• Supports -10 to 60 degrees C operating temperature 
• Supports ESD 6KV DC Ethernet protection 
• Dual power input design
  
  • 9V~48V DC wide power input, redundant power with reverse polarity protection
  • 2-pin terminal block or DC jack connector

Layer 2 Features:

• Supports IEEE 802.1Q tagged VLAN
• Supports IEEE 802.1D Spanning Tree Protocol (STP) 

Layer 3 IP Routing Features:

• IPv6 support 
• WAN Internet types: Dynamic IP(DHCP Client), static IP, PPPoE, L2TP, PPTP
• Static and dynamic (RIP1 and 2) routing
• Supports Port Forwarding, DMZ, UPnP and for various networking applications
• IP/MAC-based bandwidth control
• Supports Dynamic DNS and PLANET DDNS 

Security:

• Port filtering lets you either allow or prevent which applications can access the Internet.
• MAC filtering allows you to include or exclude computers and devices based on their MAC address
• URL filtering allows you to control access to Internet websites in an URL list
• IP source guard prevents IP spoofing attacks
• DoS attack prevention 

Management:

• Management Interfaces
  
  • Web GUI management
• Static and DHCP for IP address assignment
• System Maintenance
  
  • Firmware upload/download via HTTP
  • Hardware-based reset button for system reboot or reset to factory default
• NTP (Network Time Protocol)
• Event message logging to remote syslog server
• PLANET Smart Discovery Utility for deployment management

Compact and Cost-effective for Building Industrial IoT Networks:
PLANET WGR-500 is an industrial router designed for such Internet of Things (IoT) networks as industry, transportation, government, agriculture and other public areas. Its compact size and redundant power design are perfect for any network environment and stable operation.  The WGR-500, the best solution for any industry router application, features the following special management and operation functions:

• Setup Wizard design and IPv6/IPv4 support
• Router and switch working mode
• Firewall with 802.1Q VLAN security
• HW NAT accelerates internet NAT routing performance
• 9-48V DC redundant power design

IPv6 Support for IoT Networking:
With billions of new IoT devices entering the market each year, IPv4 is faced with the issue of not being able to fulfill the requirements of connecting all the IoT products together. IPv6 offers a highly-scalable address scheme that provides a unique 64-bit host ID to every present and future IoT device. It is sufficient to address the needs of any present and future communication device. That means IPv6 allows IoT products to be uniquely addressable without having to work around all of the traditional NAT and firewall issues.  The WGR-500 supports both IPv6 and IPv4 to ensure industrial Ethernet with a smooth migration path from the IPv4-based networks to the full IPv6 infrastructure. It assigns IPv6 addresses to clients and passes the IPv6 traffics through the IPv4 environment. The WGR-500 supports IPv4 tunneling (6to4 transition tunnel) implementations for IoT connectivity. Secure Firewall Protection:
The denial-of-service attacks (DoS) attempt to consume resources and therefore deny users network and application access. There are two types of DoS attacks – SYN floods and ping of death that consume actual server resources, or those of intermediate communication equipment, such as firewalls and load balancers, and the other, volume-based attacks like UDP/ICMP floods and other spoofed-packet floods that would saturate the bandwidth of the attacked site. The WGR-500 provides firewall to protect IoT devices against networking attack like denial-of-service (DoS), and emerging malicious traffic before attacks can occur. With firewall protection, it prevents IoT network from threats and keeps networking more secure. VLAN Support for Isolated Traffic and Security:
Virtual LANs (VLANs) offer the logical grouping technique to separate the physical ports of Ethernet switch. It can separate private network into several parts for different users. If there are too many computers or networking devices in the same network segment, it will result in heavy traffics locally. Besides, VLANs provide enhanced network security that network administrators can control over each port and whatever resources it is allowed to use. The WGR-500 supports 802.1Q VLAN to separate traffic of users and IoT devices and can work as an intelligent traffic forwarder to control traffic and isolate connections of two groups. It will not only optimize bandwidth but also improve network security. Innovative Wall-mount Installation:
The WGR-500 is specially designed to be installed in a narrow environment, such as wall enclosure. The compact, flat and wall-mounted design fits easily in any space-limited location. It adopts the user-friendly “Front Access” design, making the installing and cable wirings easy. The WGR-500 can be installed by fixed wall mounting, magnetic wall mounting or DIN rail, thereby making its usability more flexible. Dual Power Input for High Availability Network System:
The WGS-500 features a strong dual power input system (9V~48V DC) incorporated into customer’s automation network to enhance system reliability and uptime. In the example below, when the 2-pin terminal block fails to work, the hardware failover function will be activated automatically to keep powering the WGS-500 via the DC plug power alternatively without any loss of operation.