• 24x 10/100/1000BASE-T Gigabit RJ45 copper ports with 24-port IEEE 802.3af/at PoE+ injector
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 console interface for switch basic management and setup

  Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus/end-span PSE
• Backward compatible with IEEE 802.3af Power over Ethernet
• Up to 24 ports of IEEE 802.3af/IEEE 802.3at devices powered
• Supports PoE power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE management
• Total PoE power budget control
• Per port PoE function enable/disable
•  PoE admin-mode control
• PoE port power feeding priority
• Per PoE port power limitation
• PD classification detection
• Temperature threshold control
• PD alive check- PoE schedule

  Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
• Broadcast/Multicast/Unknown unicast
• Supports VLAN
• IEEE 802.1Q tagged VLAN
• Up to 255 VLANs groups, out of 4094 VLAN Ids
• Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad)
• Private VLAN Edge (PVE)
• Protocol-based VLAN
• MAC-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• IEEE 802.1D Spanning Tree Protocol
• IEEE 802.1w Rapid Spanning Tree Protocol
• IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN- BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 14 trunk groups, up to 4 ports per trunk group
• Up to 80Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops

  Layer 3 Features:

• IP interfaces (Max. 8 VLAN interfaces)
• Routing table (Max. 32 routing entries)
• Routing Protocols (IPv4/IPv6 software static routing)

  Quality of Service:

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS
• TOS/DSCP/IP precedence of IPv4/IPv6 packets
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• Multicast VLAN Registration (MVR) support

  Security:

• Authentication
• IEEE 802.1x port-based/MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers
• TACACS+ login users access authentication
• RADIUS/TACACS+ users access authentication
• Access Control List
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Source MAC/IP address binding
• DHCP Snooping to filter untrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
• Console/Telnet Command Line Interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure access
• 2.4-inch color LCD touch screen
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• Firmware upload/download via HTTP/TFTP
• Reset button for system reboot or reset to factory default
• Dual images
• DHCP Relay
• DHCP Option 82
• User Privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network Diagnostic
• ICMPv6/ICMPv4 remote ping
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• SMTP/Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events)
• SNMP trap for interface Link Up and Link Down notification
• System Log
• PLANET Smart Discovery Utility for deployment management
• Smart fan with speed control

  Redundant Power System (GS-5220-24P4XVR):

• Redundant 100~240V AC/36-60V DC dual power
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience

• 24x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with IEEE 802.3at PoE+ injector
• 4x 100/1000BASE-X mini-GBIC/SFP combo interfaces with Port-21 to Port-24
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• 1 RJ45 console interface for basic management and setup

  Power over Ethernet:

• Complies with IEEE 802.3at PoE+/end-span PSE
• Up to 24 IEEE 802.3af/802.3at devices powered
• Supports PoE power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100M
• PoE Management
• Total PoE power budget control- Per port PoE function enable/disable- PoE port power feeding priority- Per PoE port power limit- PD classification detection- PD alive check- PoE schedule- PD scheduled power recycling

  Layer 2 Features:

• IEEE 802.3x pause frame flow control (full-duplex)
• Store-and-forward architecture and “runt/CRC” filtering
• Storm control support
• - Broadcast- Unicast- Multicast
• Supports VLAN
• IEEE 802.1Q tagged VLAN
• Up to 256 VLAN groups, out of 4095 VLAN Ids
• Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
• Private VLAN Edge (PVE)- Protocol-based VLAN- MAC-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• IEEE 802.1D Spanning Tree Protocol
• IEEE 802.1w Rapid Spanning Tree Protocol
• IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
• BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 10 trunk groups, up to 16 ports per trunk group
• Up to 32Gbps bandwidth in duplex mode
• Provides port mirror (many-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops

  Layer 3 IP Routing Features:

• Supports a maximum of 8 static routes and route summarization
• Supports a maximum of 32 routing entries

  Quality of Service:

• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS- IP TOS/DSCP/IP precedence
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Traffic-policing on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Support MLD snooping v1 and v2
• Supports querier mode
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)

  Security:

• IEEE 802.1x port-based/MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers
• RADIUS/TACACS+ customers access authentication
• IP-based access control List (ACL)
• MAC-based access control list
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP inspection discards ARP packets with invalid MAC address to IP address binding
• IP source guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• Switch management interfaces
• Console and Telnet command line interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure access
• Four RMON groups (history, statistics, alarms and events)
• IPv6 address, NTP and DNS management
• Built-in Trivial File transfer Protocol (TFTP) client
• DHCP client
• Firmware upload/download via HTTP/TFTP
• DHCP Relay
• DHCP Option 82
• Customer Privilege levels control
• NTP (network time protocol)
• Link Layer Discovery Protocol (LLDP)
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• Reset button for system reboot or reset to factory default

  Redundant Power System (GS-5220-24PL4XR):

• Redundant 100~240V AC/36~60V DC dual power
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience

• 48x 10/100/1000BASE-T Gigabit RJ45 copper ports with 48-port IEEE 802.3af/at PoE+ injector
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 console interface for switch basic management and setup

  Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus/end-span PSE
• Backward compatible with IEEE 802.3af Power over Ethernet
• Up to 48 ports of IEEE 802.3af/IEEE 802.3at devices powered
• Supports PoE power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE management
• Total PoE power budget control- Per port PoE function enable/disable
• PoE admin-mode control
• PoE port power feeding priority
• Per PoE port power limitation
• PD classification detection
• Temperature threshold control
• PD alive check
• PoE schedule

Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
• Broadcast/Multicast/Unknown unicast
• Supports VLAN
• IEEE 802.1Q tagged VLAN
• Up to 255 VLANs groups, out of 4094 VLAN Ids
• Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad)
• Private VLAN Edge (PVE)
• Protocol-based VLAN
• MAC-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• IEEE 802.1D Spanning Tree Protocol
• IEEE 802.1w Rapid Spanning Tree Protocol
• IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
• BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 26 trunk groups with 4 ports for each trunk group
• Up to 80Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops

  Layer 3 Features:

• IP interfaces (Max. 8 VLAN interfaces)
• Routing table (Max. 32 routing entries)
• Routing Protocols (IPv4/IPv6 static routing)

  Quality of Service:

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS
• TOS/DSCP/IP precedence of IPv4/IPv6 packets
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• Multicast VLAN Registration (MVR) support

  Security:

• Authentication
• IEEE 802.1x port-based/MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers
• TACACS+ login users access authentication
• RADIUS/TACACS+ users access authentication
• Access Control List
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Source MAC/IP address binding
• DHCP Snooping to filter untrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
• Console/Telnet Command Line Interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure access
• IPv6 IP Address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• Firmware upload/download via HTTP/TFTP
• Reset button for system reboot or reset to factory default
• Dual images
• DHCP Relay
• DHCP Option 82
• User Privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network Diagnostic
• ICMPv6/ICMPv4 remote ping
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• SMTP/Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events)
• SNMP trap for interface Link Up and Link Down notification
• System Log
• PLANET Smart Discovery Utility for deployment management
• Smart fan with speed control

  Redundant Power System (GS-5220-48P4XR):

• Redundant 100~240V AC/36-60V DC dual power
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience

• 48x 10/100/1000BASE-T Gigabit RJ45 copper ports with 48-port IEEE 802.3af/at PoE+ injector
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 console interface for switch basic management and setup

  Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus/end-span PSE
• Backward compatible with IEEE 802.3af Power over Ethernet
• Up to 48 ports of IEEE 802.3af/IEEE 802.3at devices powered
• Supports PoE power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE management
• Total PoE power budget control- Per port PoE function enable/disable
• PoE admin-mode control
• PoE port power feeding priority
• Per PoE port power limitation
• PD classification detection
• Temperature threshold control
• PD alive check
• PoE schedule

  Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
• Broadcast/Multicast/Unknown unicast
• Supports VLAN
• IEEE 802.1Q tagged VLAN
• Up to 255 VLANs groups, out of 4094 VLAN Ids
• Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad)
• Private VLAN Edge (PVE)
• Protocol-based VLAN
• MAC-based VLAN
• Voice VLAN
• Supports Spanning Tree Protocol
• IEEE 802.1D Spanning Tree Protocol
• IEEE 802.1w Rapid Spanning Tree Protocol
• IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
• BPDU Guard
• Supports Link Aggregation
• 802.3ad Link Aggregation Control Protocol (LACP)
• Cisco ether-channel (static trunk)
• Maximum 26 trunk groups with 4 ports for each trunk group
• Up to 80Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops

  Layer 3 Features:

• IP interfaces (Max. 8 VLAN interfaces)
• Routing table (Max. 32 routing entries)
• Routing Protocols (IPv4/IPv6 software static routing)

  Quality of Service:

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
• IEEE 802.1p CoS
• TOS/DSCP/IP precedence of IPv4/IPv6 packets
• IP TCP/UDP port number
• Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking

  Multicast:

• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• Multicast VLAN Registration (MVR) support

  Security:

• Authentication
• IEEE 802.1x port-based/MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers
• TACACS+ login users access authentication
• RADIUS/TACACS+ users access authentication
• Access Control List
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Source MAC/IP address binding
• DHCP Snooping to filter untrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder

  Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
• Console/Telnet Command Line Interface
• Web switch management
• SNMP v1, v2c, and v3 switch management
• SSH/SSL secure access
• IPv6 IP Address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• Firmware upload/download via HTTP/TFTP
• Reset button for system reboot or reset to factory default
• Dual images
• DHCP Relay
• DHCP Option 82
• User Privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network Diagnostic
• ICMPv6/ICMPv4 remote ping
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• SMTP/Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events)
• SNMP trap for interface Link Up and Link Down notification
• System Log
• PLANET Smart Discovery Utility for deployment management
• Smart fan with speed control

  Redundant Power System (GS-5220-48PL4XR):

• Redundant 100~240V AC/36-60V DC dual power
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience

• 24x 10/100/1000BASE-T RJ45 copper ports
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RJ45 to DB9 console interface for switch basic management and setup
• One 10/100BASE-TX Management port 

Stacking Features:

• IP Stacking
  
  • Connects with stack member via Gigabit TP, SFP and 10G SFP+ interfaces
  • Single IP address management, supporting up to 16 IP units stacked together
• Hardware Stacking
  
  • Virtualized multiple SGS-5240 switch series stacked into one logical device
  • Connects with stack member via assigned 10G SFP+ interfaces
  • Single IP address stack management, supporting up to 6 hardware units stacked together
  • Stacking architecture supports redundant ring mode

IP Routing Features:

• IPv4/IPv6 hardware static routing
• Routing interface provides per VLAN routing mode 

Layer 2 Features:

• Supports VLAN
  
  • IEEE 802.1Q tag-based VLAN
  • Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported
  • GVRP for dynamic VLAN management
  • Protocol-based VLAN
  • MAC-based VLAN
  • IP subnet-based VLAN
  • Voice VLAN
• Supports Link Aggregation
  
  • 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
• Supports Spanning Tree Protocol
  
  • STP, IEEE 802.1D (Classic Spanning Tree Protocol)
  • RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
  • MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
  • Supports BPDU & root guard
• Port mirroring to monitor the incoming or outgoing traffic on a particular port (many to one)
• Supports G.8032 ERPS (Ethernet Ring Protection Switching)
• Loop protection to avoid broadcast loops
• Link Layer Discovery Protocol (LLDP)
• Compatible with Cisco uni-directional link detection (UDLD) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices 

Quality of Service:

• Input and output rate limit per port bandwidth control
• 8 priority queues on all switch ports
  
  • IEEE 802.1p CoS/DSCP/IP Precedence
  • VLAN ID
  • ACL
  • Policy-based ingress and egress QoS 

Multicast:

• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD snooping v1 and v2
• Querier mode support
• IPv4 IGMP snooping port filtering
• IPv6 MLD snooping port filtering
• MVR (Multicast VLAN Registration) 

Security:

• Authentication
  
  • IEEE 802.1x port-based/MAC-based network access authentication
  • IEEE 802.1x authentication with guest VLAN
  • Built-in RADIUS client to cooperate with the RADIUS servers
  • RADIUS/TACACS+ users access authentication
  • Guest VLAN assigns clients to a restricted VLAN with limited services
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List (ACL)
  • Time-based ACL
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder 

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
  
  • Console and Telnet Command Line Interface 
  • HTTP web switch management
  • SNMP v1 and v2c switch management
  • SSHv2, SSLv3 and SNMP v3 secure access
• SNMP Management
  
  • Four RMON groups (history, statistics, alarms, and events) 
  • SNMP trap for interface Link Up and Link Down notification
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
• • Firmware upload/download via HTTP
  • Reset button for system reboot or reset to factory default
  • Dual images
• DHCP Functions:
  
  • DHCP Relay
  • DHCP Option 82
  • DHCP Server
• User Privilege levels control
• Network Time Protocol (NTP) and SNTP
• Network Diagnostic
  
  • SFP-DDM (Digital Diagnostic Monitor)
  • Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
  • ICMPv6/ICMPv4 remote ping
• Syslog remote alarm
• System Log 

Power over Ethernet:

• Complies with IEEE 802.3at Power over Ethernet Plus
• Up to 24 ports of IEEE 802.3at PoE devices powered
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE management
  
  • Total PoE power budget control
  • Per port PoE function enable/disable
  • PoE port power feeding priority
  • PD classification detection

• 24x Gigabit PoE+ Ports
• 4x 10G SFP+ Slots
• RJ45/Micro-USB Konsolen Port
• 802.3at/af, 384 W PoE Power
• 1HE 19-Zoll-Rack-montierbares Stahlgehäuse
• Features:
  • Integration mit Omada SDN Controller, Static Routing, OAM, sFlow, DDM, 802.1Q VLAN, QinQ, STP/RSTP/MSTP, IGMP Snooping, 802.1p/DSCP QoS, ACL, 802.1x, Radius/Tacacs+ Authentifizierung, LACP, CLI, SNMP, Dual-Image/Konfiguration, IPv6

• Blitzschnelle 10G Uplinks: 4× 10Gbit/s SFP+-Slots und die volle Switchkapazität sichern die volle Uplinkbandbreite high-bandwidth connectivity and non-blocking switching capacity. 
• 384W PoE-Leistung: 24× 802.3at/af-konforme PoE+-Ports haben einea total power supply of 384 W*.
• In Omada integriert: Zero-Touch Provisioning (ZTP)**, zentrales Cloud Management und intelligentes Monitoring.
• Zentrales Management: Cloudzugriff und Omada App für eine ultra einfache und praktische Verwaltung.
• Statisches Routing: Hilft bei der Weiterleitung von internen Datenübertragungen für eine effizientere Nutzung der Netzwerkressourcen.
• Robust Security Strategies: IP-MAC-Port Binding, ACL, Port Security, DoS Defend, Storm control, DHCP Snooping, 802.1X, Radius Authentication und mehr.
• Optimize Voice and Video Applications: L2/L3/L4 QoS and IGMP snooping.
• Standalone Management: Web, CLI (Console Port, Telnet, SSH), SNMP, RMON und Dual Image liefern leistungsstarke Managementkapazitäten

• 9x GbE RJ45 Ports
• 4x 10G SFP+ Ports
• Integrierter Layer-2-Switch*
• Bis zu 9.500 Mbps NAT-Durchsatz**
• Traffic-Shaping-Funktionalität und automatische Kundensperrung
• Firewall und OSPF-Routing
• Zusätzlicher Power TransPort-Eingang für DC-Redundanz

*Die Ports 1-8, 10-13 können für Line-Rate Layer2-Switching konfiguriert werden.
**Bis zu 2.250 Mbit/s bei aktiviertem QoS; bis zu 7.500 Mbit/s bei aktiviertem IP Accounting.

• 4x 2.5 GbE RJ45 Ports mit 27V passivem PoE Ausgang
• 4x 10G SFP+ Ports
• 160 W (27 V) PoE-Gesamtverfügbarkeit*, 20 W/Port (2-Paar) / 40 W/Port (4-Paar)
• Port-Isolierung, Geschwindigkeitsbegrenzung und DHCP-Snooping-Funktionalität
• 1x Power TransPort™ Eingang für DC-Redundanz
• Tisch-, Wand-, 1HE-Rack- und Außenmontage**
• Eigenständige Verwaltung über lokale Webschnittstelle und UISP-Anwendungsintegration

*Bei Stromversorgung über den mitgelieferten AC/DC-Adapter.
**Wenn in der UISP Box Plus (separat erhältlich) enthalten.

• 24x GbE RJ45-Ports, davon (16) mit 27 V passivem PoE-Ausgang
• 4x 10G-SFP+-Ports
• 220 W (27 V) Gesamt-PoE-Leistung, 15 W/Port (2-Paar) / 30 W/Port (4-Paar)
• 1,3"-LCM-Farb-Touchscreen
• Einfache Bluetooth-Einrichtung mit der UISP Mobile App

• 48x 2.5G/1G/100MB 802.3af/at PoE+ RJ45 ports
• 4x 10G/1G SFP+ ports
• 720W PoE Gesamtleistung
• Layer3 Switching Features
• 1.3" Touchscreen mit AR Switch Management
• UniFi SmartPower RPS DC Eingang

Layer 3, PoE-Switch mit 48x 2,5GbE, 802.3at PoE+ RJ45-Ports und 4x 10G SFP+-Ports. Der Switch Enterprise 48 PoE (USW Enterprise 48 PoE) ist ein vollständig verwalteter Switch mit 48x 2,5 GbE, 802.3at PoE+ RJ45-Ports, 4x 10G SFP+-Ports und einer PoE-Gesamtversorgung von 720 W. Neben seiner Layer-3-Funktionalität bietet dieser Switch eine umfangreiche Suite von Layer-2-Switching-Protokollen, einschließlich portspezifischer Betriebsmodi (Switching, Mirroring oder Aggregat). Der USW Enterprise 48 PoE verfügt außerdem über einen 1,3-Zoll-LCM-Farb-Touchscreen, der prägnant anzeigt wichtige System- und Verbindungseinblicke. Darüber hinaus bietet das USW Enterprise 48 PoE einen verbesserten Ausfallschutz der Stromversorgung, wenn es an das SmartPower Redundant Power System (USP RPS separat erhältlich) angeschlossen ist. Dieser Switch kann mit der leistungsstarken, intuitiven UniFi Network-Webanwendung und der mobilen App von überall aus überwacht oder konfiguriert werden.

• 24x 10/100/1000BASE-T Gigabit RJ45 copper ports with 24-port IEEE 802.3af/at PoE+ injector
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
• RS-232 RJ45 console interface for switch basic management and setup   

Wireless LAN AP Management:

• Dashboard: provides at-a-glance view of system and wireless network status
• AP Discovery: one key to discover the managed APs on the managed LAN
• Customized Profile: allows multiple wireless profiles creation and maintenance
• Auto Provision: multi-AP provisioning with one click
• Cluster Management: simplifies high-density AP management
• Zone Plan: optimizes AP deployment with actual signal coverage
• Analysis: real-time AP status monitoring
• Scalability: free system upgrade and AP firmware bulk upgrade capability 

Power over Ethernet:

• Up to 24 ports of IEEE 802.3af/802.3at devices powered
• Supports PoE Power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100 meters
• PoE Management
  
  • PoE Port Status monitoring
  • Total PoE power budget control
  • Over temperature protection
  • PoE usage threshold
  • Temperature threshold
  • Per port PoE function enable/disable
  • PoE Port Power feeding priority
  • Per PoE port power limit
  • PD classification detection
  • Sequence port PoE 

Layer 2 Features:

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
  
  • Broadcast/Multicast/Unknown unicast
• Supports VLAN
  
  • IEEE 802.1Q tagged VLAN
  • Up to 255 VLANs groups, out of 4095 VLAN IDs
  • Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad)
  • Private VLAN Edge (PVE)
  • Protocol-based VLAN
  • MAC-based VLAN
  • Voice VLAN
• Supports Spanning Tree Protocol
  
  • IEEE 802.1D Spanning Tree Protocol
  • IEEE 802.1w Rapid Spanning Tree Protocol
  • EEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
  • BPDU Guard
• Supports Link Aggregation
  
  • 802.3ad Link Aggregation Control Protocol (LACP)
  • Cisco ether-channel (static trunk)
  • Maximum 14 trunk groups, up to 4 ports per trunk group
  • Up to 80Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports ERPS (Ethernet Ring Protection Switching) 

Layer 3 IP Routing Features:

• Supports maximum 128 static routes and route summarization
• IP dynamic routing protocol supports OSPFv2
• Routing interface provides per VLAN routing mode  

Quality of Service:

• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8 priority queues on all switch ports
• Traffic classification
  
  • IEEE 802.1p CoS
  • TOS/DSCP/IP Precedence of IPv4/IPv6 packets
  • IP TCP/UDP port number
  • Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic policing on the switch port
• DSCP remarking 

Multicast:

• Supports IGMP Snooping v1, v2 and v3
• Supports MLD Snooping v1 and v2
• Querier mode support
• IGMP Snooping port filtering
• MLD Snooping port filtering
• Multicast VLAN Registration (MVR) support 

Security:

• Authentication
  
  • IEEE 802.1x Port-based/MAC-based network access authentication
  • Built-in RADIUS client to co-operate with the RADIUS servers
  • TACACS+ login users access authentication
  • RADIUS/TACACS+ users access authentication
• Access Control List
  
  • IP-based Access Control List (ACL)
  • MAC-based Access Control List
• Source MAC/IP address binding
• DHCP Snooping to filter un-trusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• Auto DoS rule to defend DoS attack
• IP address access management to prevent unauthorized intruder 

Management:

• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
  
  • Console/Telnet Command Line Interface
  • 2.4” inch LCD touch screen
  • Web switch management
  • SNMP v1, v2c, and v3 switch management
  • SSH/SSL secure access
• IPv6 IP Address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
  • Firmware upload/download via HTTP/TFTP
  • Reset button for system reboot or reset to factory default
  • Dual Images
• DHCP Relay
• DHCP Option82
• User Privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network Diagnostic
  • ICMPv6/ICMPv4 Remote Ping
  • Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues
• SMTP/Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events) 
• SNMP trap for interface Linkup and Linkdown notification
• System Log
• PLANET Smart Discovery Utility for deployment management